Counting matching models…
A twist on the famous Moai statues on Easter Island. Use glue stick when printing. Also needs support. I used tree supports with 30 degree threshold angle from build plate only. Remove small overhangs.
Comes with two different twist options; form fitted and round. Use a bit of glue on the print surface to ensure good adhesion. Printed with 15% Gyroid.
Sturdy drumstick holder for an electric drum set. This clips nicely on the rack of my Roland TD-17 but should fit any rack tube measuring 40mm. Print with top face down on print bed. Did not require supports on my Carbon X1. Printed with…
Looks great sitting on desk. Use a bit of glue to ensure adhesion Printed with 15% gyroid
Print the “TopBladeless” file instead of “Top file” if you just want the fidget toy version instead of a sharp razor. Depending on which one you build, you'll need different parts: Parts List Utility blade version: 4 x M3x16mm cap machine…
Designed for organizing my ferrules/spades/wire nuts and similar small parts. Requires two M3x30mm machine screws to assemble. The clip brackets have one hole that's larger than than the one across from it. Start there with the screw,…
First attempt at this sort of fidget
Lid sides close with a snap and holds securely. Front lip is raised to allow your thumbs to purchase the lid while opening. I printed the Lid with 100% infill. Box is printed with 10% Gyroid infill. Generic PLA seems to work fine. Box…
The twist will pass through the outer part in any orientation but only one will line up flush. Add a bit of glue stick to the plate before printing. I'll post two profiles, one for .16mm and for .20mm layer height. Depending on what…
This headphone holder was designed to fit perfectly on the rack of my Roland TD-17 but should fit any rack tube measuring 40mm. The clip prints seperately, just add some super glue and you're ready to rock. The headphone holder itself…
Domino is fun to fidget with and easy to print. The Joint is print-in-place. If you want to print it in single color, simply erase all painting. joints should move freely right off the built plate, but if they don't just turn them to…
For Case: Wall loops: 4 Gyroid infill at 10% Top layer pattern is set to Archimedean Chords but you can change this to your preference For Lid: 100% Infill Concentric top surface pattern. Again, to taste but I like the way this pattern…
No brim needed but I recommend glue on the print bed. 8% gyroid infill Needs support. I used tree supports from build plate only. Remove small overhangs checked.
I used a section of Bambu's 6500K White LED Light Strip (KA004) along with female USBC ports to make it glow (soldering required). The hole in the back piece is designed to fit the female USBC port. After LEDs were installed, I superglued…
Stash your worthless trinkets in this box. Comes complete with layer lines, proof that it was 3d printed by the hard-working, indigenous peoples of…wherever. Just add a few M3x30mm machine screws to keep your trinkets safe. You're a…
Requires four M3x30mm machine screws for clasps. Profile is set to print in Bambu PETG HF but prints fine in PLA Basic
The tray measures 175x120mm and uses nine 15x2mm magnets centered on select sections of the tray. Upload has two versions objects; Magnetic and Non-Magnetic. If you don't want to insert magnets, just print the non-magnetic version. If you…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 168.67x253mm in size You may print at higher layer heights below the Min Depth of 0.24mm The Max Depth is 3mm and the Actual Depth is 3.1mm…
Case for the Talent Cell model PB240A1. Made with testing LED strips in mind (12v-24v) Hinges are print in place. Requires four M3x30mm machine screws to assemble clasps. Clasps are printed in Bambu PETG HF and the case in PLA basic. The…
These are all currently available results.
