48 models
Update 5/17: Added a bottom with a GoPro mount. With a couple GoPro arms you should be able to use my Yeti pop filter with this mic holder: https://www.thingiverse.com/thing:4234982 . Update 5/3: Added step file and 1/4" threaded bottom.…
Be warned, current version is large and heavy. It's still WIP while I'm trying to lighten it up and save printing time. The gauntlet has a 5" small opening and a 8.5" large opening and is about 10" at its widest width. The eight sections…
This is a collection of trays for the 2015 and above Chevy Colorado. There are very few (no?) commercial trays custom to the Colorado and since the Colorado does not have a sunken ridge most generic trays interfere with the closure of the…
So... a legitimate grit guard will likely run you less money than the cost of the filament to print this one and with Amazon Prime you'll likely receive it before this print would complete. However I'm sure someone will find themselves in…
This is a fine tip nozzle for the Ryobi low-pressure inflator. It's great for using the inflator to clean out small electronics such as a PC case. This is a simple design but it was used as an example of how to use the 'Sheet Metal'…
This is a gantry conversion kit for the TronXY X5SA 400. It should work with the other X5SA models however you'll need to adapt the length of the linear rail (450mm for X5SA 400). Check out the installation video here:…
This mount conforms to the dashboard and tray contours of the 2015 and above Chevy Colorado and GMC Canyon. There's room for double-sided tape on the back of the mount in the tray area and in the front of the mount on the stereo fascia -…
The clip that comes with the Boya M1 is perpendicular - ideal for zippers, button-up shirts, ties, etc but I'm often in a t-shirt. You can loosen and twist the included clip but it's a bit unstable in its other orientation. This clips…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/3DPrinterSystem.html These models comprise enclosures for control boards, mosfets, LCDs, etc as part of the Big Plans Printer System. LCD Front - Front panel…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/ZGantry.html Here is the gantry installed in an FT5: These models comprise a three-Z-motor gantry for completely automated bed leveling for cube…
The Big Plans Three Motor Z Gantry (https://www.printables.com/model/240093) is made to work in most cube style printers - the X5SA included. These additional parts make adapting the OEM X5SA to the Big Plans Triple Z gantry as cheap and…
With two steppers on the same driver you constantly have to worry about the steppers falling out of sync when unpowered. If you link them then things get a little better but you're in a big mess if you do skip a step or pull over a cable…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/Frame.html This is a collection of 2020 and 2040 joint plates mainly used for construction of a cube-style 3D printer frame. 2020 plain corner -…
UPDATE 11/28: A commenter on my YouTube review of this case ( https://www.youtube.com/watch?v=lrJwxctFG7Q&t=1s ) requested a perforated version so air could still be drawn in through the gap. Printing the perforated version is a bit of a…
Here's my Take on Oculus Touch grips for Beat Saber. I designed these to be as safe as possible - for a 3d printed design. The cups support screw tightening (m3) but also have a place to string the built-in controller tether as well as…
These simple little standoffs are good for attached and supporting electronic boards (including motherboards) to wood. They are designed so that standard motherboard mounting screws or #4 wood screws can be used to secure the motherboard…
The TronXY X5SA series printers come with basic acrylic motor mounts and poorly aligned CoreXY cables leading to the Y carriages. In CoreXY it is important that the cables leading to the Y carriages are parallel to the Y axis, otherwise…
The tiny front pocket in the dash of the '15 and up Colorado is nearly useless. Even if you shove a wallet or garage door opener in there it'll slide right out if you hit the gas at all. This 'pocket dock' for phone or tablet gives it…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/Mock.html These models comprise mock parts that represent many of the purchased parts used to build a 3D Printer including basic extrusions,…
These prints can be used with a galvanized 5/16 bolt, nut, and washer to mount a Lowrance transducer in the scupper holes of a Moken 12.5 Kayak. I imagine it could also be easily customized to other kayak makes and models if not used as…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/Accessories.html These models comprise accessories for tool and spool storage and organization. 2020 Spool Holder - mounts to your frame, holds a…
Bought the Ryobi 18v One+ shop Vac because it was both powerful and portable. Ideal for vacuuming out the cars or far corners of the garage. Home Depot sells a pack of precision cleaning implements for a 1.25" hose (seems to be typical on…
All of the models required to convert your Aquila or Ender 3 to dual extrusion are included here. The overall process is detailed in this video: At a high level: Disconnect and remove the old control board - there are not enough stepper…
As all owners of TronXY X5SA are aware, it can be very difficult to keep the bed level. The lead screws are attached directly to the shafts on the dual-Z steppers and with just a light touch one side can slide out of sync with the other.…
I created some amplifier circuits for my virtual pinball project: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/ I build them on small, cheap uxcell 4x6cm perf boards:…
If you do a lot shallow-water kayak (or small boat) fishing you already know what a stake-out-pole is. If you don't, a stake out pole is a replacement for an anchor in water that is more shallow than the pole length. You simply drive the…
Update 5/13: Increased the material around the female pin section of the case. Only 7segledcase1.stl has changed - pin size has not changed. Update 3/13: There was a 2mm border around each segment due to the backplay segments being…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/ZGantry.html These models comprise a two-Z-motor gantry for many configurations of cube-style printers using 8mm smooth and threaded rods. Smooth…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/Accessories.html These models comprise the CoreXY Gantry (motor mounts, pully blocks, y carriages) for the Big Plans Printer System. It is…
When you attach your phone in CarPlay mode you can't use it however you still don't want it rattling around in your console pockets. This case will friction-fit an OEM iPhone lightning cable and secure your phone in an easy-to-remove…
Given the excitement around Cyberpunk I wanted to add some related flair to my case. This design is pretty simple. It's a 'tray' in which to mount ws2812b LED strips and a press-fit 'frame' to stand the tray up vertically. The tray serves…
I'm using small push solenoids as strikers for my pinball cabinet project: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/ The solenoids I purchased did not have mounting tabs so I designed these little strikers. The horizontal…
This print allows you to mount a Lowrance fish finder (in my case a Mark-4 CHIRP) on any rail system. Definitely print with supports everywhere and with decent infill for strength. There are two STLs on this item. One that mounts the FF…
It may not be the most exciting mountain however it's one of my favorite places to ski and I was surprised that noone had made it before. The map screenshot should correlate pretty close to the model. How I Designed This Map section…
This is a collection of gadgets and tool holders I'm using on my personal printer. This includes: A handle-like model that I use to mount my webcam to for OctoPi A raised LED bar mount so that my lights hang above the CoreXY cables Tool…
Update 11/13/2016 - The topless versions require a new 'female' base. Added female and male bases. I've now installed the open-face chain and printed a couple test prints. If you want a complete, open-face chain I would suggest printing…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/printersystem/XCarriage.html These models are for a Bowden (single or dual via chimera/cyclops) X-Carriage compatible with the Big Plans 3D Printer System X/Y…
This is an enclosure for the DIY PiKVM kit consisting if: Raspberry Pi 4b: https://www.adafruit.com/product/4295?src=raspberrypi USB-C/PWR splitter: https://www.pishop.us/product/usb-c-pwr-splitter/ HDMI CSI-2:…
This is my design for a direct drive extruder setup on a TronXY X5SA (400 in my case) utilizing a linear rail (MGN12H) mounted on the bottom side of the X-axis 2020 extrusion. This gantry can use the supplied stepper, extruder, X…
Edit 9/8: One of the connectors on my TriGorilla mosfet melted and I replaced it with a smaller, cheaper version. It looks like there are two common styles, a 30A (similar to the original TriGorilla) and a smaller 25A which seems to be…
These models are part of the Big Plans 3D Printer System: https://lilmikey.com/3DPrinterSystem.html These models comprise a Direct Drive X Carriage using a standard sized 42n NEMA 17 stepper, a motor-mounted extruder like the BMG or…
!!!These items are still WIP!!! UPDATE 1/31: Added FT4, FT10, and FT10/FT4 Merged copies that fit the new idler design. I do not have the bolt and bearings to test with so feedback or suggestions are welcome. UPDATE 11/20: Added a number…
Have a bunch of folder labels, have a bunch of tool. Use the labels to tag the tools. The exact labels I'm using are no longer available but should fit these with no issue:…
This is a simple little box that holds a flyback diode for solenoid flyback protection in my virtual pinball cabinet: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/ The diode is needed to 'short circuit' any current caused by the…
Need to run eight light-gauge wires somewhere? Have spare 4x6cm prototyping boards and surface-mount screw connectors lying around? Here is a solution for you! I designed this to run thermistor, fans, and sensors lines to my hot end.…
These little enclosures are for the PCB-style ethernet breakout boards that are design for pin-headers. When you need a bunch of small wires I'm a big fan of ethernet cable as it's generally fairly durable, reasonable insulated, and very…
UPDATE 4/27: I still see a lot of folks downloading and liking this carriage. I'm glad people are finding it useful and it's still a great replacement for the stock carriage - especially if want to maintain compatibility with other parts…
Update 11/15: Switched to a BMG vlone and added a compatible part cooler blower channel for BMG+V6+Volcano. Piezo leveling is still working great and I have switched back and forth between the Aero and BMG with almost no adjustment.…
These are all currently available results.
