39 models
Now with 100% less motor Mounts!* The revised Body is through testing and now no longer requires fiddly motor mounts. The body works with both N10's and N20's, just clip the little tab out of the way if using with N20's. This works with…
Simple changes to the standard case - Parts are for LH, please mirror in printing to make RH parts. Now compatible with AliExpress PCB's too! Heat press inserts are removed and replaced with holes for a countersunk Polyfix or self tapping…
Simple Pinch trainer for climbing, I find it very similar to the Quad block, but a little harder to grip thanks to the layer lines on a print. There are two files available, one with a slight angle on the outside and one with a more…
Quick Tester for a larger Lego-Compatible Robotics Project. 2x Standard Brick Height, should work with anything lego compatible. Uses a standard plate on top to retain the motor. Early revision published 17/07/25.
Newer Version found here - https://www.printables.com/model/1216336-modulant-v2 This robot can be built up as a spinner, wedge, lifter, flipper, hammersaw etc. It's designed to fit near any wheel available, from 20mm to 46mm in diameter,…
This is a simple pusher robot, designed for use with Generic 44mm N20 Wheels. It was inspired by the powerloader from Aliens, and uses some design points from the movie prop as decoration. This can be built as high or low tech as you…
Simple Pot to hold knick-knacks and suchlike. Base diameter is 46mm, and internal height about 55mm so should fit a standard LED candle in there for spooky effects.
Printable Motor Mounts for N20 styled motors. The standard version uses 2x M2 nuts or M2 standoffs, with 18mm hole centres. There is a version designed for use with self tapping screws or Polyfix screws (3x8) which is slightly more…
Simple mono pocket trainer, stick some cord through the loop and increase the weight as required.
Simple Chip for your climbing wall. Uses two woodscrews to attach to a board, suitable sizes are from 3.5-5mm, or #6-#10, and I would recommend a minimum of 20mm or ¾ Long. Print with 4+ walls, tested in PLA at 0.2mm Layer height, 15%…
Hub for two pololu tyres to be mounted on a standard 3mm D shaft. I use these with N10's and a drop of superglue to hold them on with pretty good results. I have a 1.5MOD gear drive version which should be uploaded soon but still needs…
A simple and cheap pushing robot. For the other robot in the main photo please see Edward II . It takes 2x N20's with standard mounts, and can be ran either with a malenki, a dual ESC or even standard RC car hardware. Includes spots for…
Quick little Removable Link block. Uses hexagon spacers to stand-off from the top panel, the fastening screws can also be used to hold a link cover on. Update 30/01/25 I have included a link cover, and there is now a drill template to use…
Provolone Ranger - A simple 150g fighting robot, designed for a fun time, not to be a serious competitor despite its win rate. Uses 3x N10 motors, one for the manipulator arm and two for drive. Uses standard N20 mounts for the motors with…
Quick Model for a Sortimo/L-Boxx Case to add a standard ¼" thread on the lid. useful for mounting lights, magic arms, helping hands etc. Uses 3-6 x Polyfix Screws or appropriate self tapping screw to mount to the box, and a standard ¼-20…
Covers for FlySky Fs-6x and FlySky FS-i6x style transmitters to protect the gimbals and switches in transport. I've broken enough switches that it was time to get something more suitable for the abuse my gear goes through, getting chucked…
Wheel hub for 30mm Ranglebox tyres . Compliant, designed to be printed out of TPU, I use the same hub with a gear fitting on my competitive Antweights (150g). Since moving to these we've had significantly less motor failures due to the…
V0.1 - Untested 12/01/25 I needed a quick holder for some homelab parts, and here we are. I always assumed that rackmount hole spacings were even, and once I learned they're a repeating pattern which constrains you to 40mm tall modules I…
Inspirational signage for your washroom. Files contain a both the flat bottom sign, and a small stand piece if you want to display this on a shel, it will require a little superglue to attach. alternatively, command strips can be used if…
Simple model for a Can Holder, used as a prototype for sizing a model for work. Updated with a standard 330ml EU can version - I used the wrong model for Sizing
Simple Ice scraper - Tested in PLA, but you may have better results with a filament with a little bit of give to conform to the screen better. Wider version at 105mm for better coverage also uploaded
Simple mount for a Pi 400 to fit in a 10" server rack for homelab use and/or tinkering. Really thin form factor, great for non-fixed layouts like QuickRack or other extrusion based systems. First step towards a blade style Pi Cluster…
Wall mount ER32 Collet Holder to get your tooling up and organised!
Basic Antweight designed to use a Generic 8W soldering iron element and Generic 20A RC switch to melt its opponents! on 1000RPM N10's its incredibly nippy. This is a very old design, so it has a few Issues. These should be fixed in the V2…
Simple tyre mount for Lego wheels and Ranglebox/Repeat Hubs. Tested in TPU 95A without any issues, but not tested in full combat yet. I'd superglue the Rims to the tyres once installed fully, its quite difficult to get them to seat fully…
Generic ¼ Screwdriver holder. Designed to take any drive bit extension as its holder, just drive it in with a press or a hammer. Used the prototype for a few months now in the workshop without any serious issues Has a spinning palm cap…
Simple ER32 Collet holder in 3x3, 2x3 and 1x3 layouts - Untested as of yet. Perfect for organising a small selection.
A simple wheel hub for 2.5mm D shaft motors. I'd recommend a drop of superglue to hold them on the shaft
Dual-Tyre wheel for the Ranglebox 50mm Tyres and Mars Hubs Compliant when printed in TPU, I'd recommend attaching the tyres with superglue to keep them on when the hubs deflect. Updated Deep Hub Model 31/05 for better rigidity
Quick Model for a Wall mount for our transmitters - Couldn't find one online so I threw this together.
Simple Sleeve to grip the tapered shaft of a soldering iron Absolutely not a sponsored post
Generic Holder for a standard power supply. Can be mounted down to a board or extrusion, and removed with only 4 screws. Holders for M3 nuts on the inside of the panel for the XT60 and IEC. Not the best orientation for cable exit, but it…
Uses M6 Hexagon spacers to provide a fastening surface for top and bottom panels to robots. I have used these in a few featherweights, and haven't experienced a failure yet. A 4WD robot with these mounts has been tested up to 88Kg and…
Quick modification to let me use these screwdrivers in a little portable rack. I don't have the imperial set, but assuming the handles are the same size it should fit them too.
XT30 Link Insertion Tool Designed to allow for a more positive insertion of a recessed power link, leading to a more reliable device.
Simple Holder for R8 tooling for a mill Could be used to hold collets too, but this is probably overkill in that case.
A redesign of the Excellent Accu Bag Holder to better reflect its alternative purpose as a baked bean storage solution. It transforms from a simple bag holder into a practical food storage system, adding value for users who need a real…
Simple holder for the Generic Boring Head and R8 Arbor Combination
A Little holder for the Aeropress plunger. In my search for a grinder that fits inside the Aeropress for bikepacking, I realised that it doesn't have to fit in the plunger at all.
These are all currently available results.
