Counting matching models…
Edit from April 24th 2023 Per request, I've added holes which “ should” work with SCPH-3000x I don't have any other model on hands than my 39000 so do it at your own risk. I'm keeping the old ones working on 39000 for now.…
So after moving a Detolf, two feet broke when they got stuck into a transition strip. So I made a new foot. They are not quite exactly the same shape but similar enough and same height.
Note: I forgot to update but the thing need an hole/cable pass-through on the top of the tray or the top won't close. Here's all the 3D printed part I used to do this mod. There's are some part I used like the PCB for splitting the +5v…
The Mean Well LRS-600-24 is using a 12V fan, so it can be easily replaced with a quiet one, like a Noctua (you'll need an adapter for the JST PH 2.54 2PIN connectors) Two possibilities: LRS-600-24.STL : the fan is INSIDE (with grid). You…
NOTE: /!\ Installing the new housing on the print head is painful /!\ You'll need to make a splitter or solder on the Fan0 of the PCB. EDIT 2023-04-23 : Add an other vent for TMC drivers EDIT 2022-09-05 : Adding a zip files with SD card…
Here's a full frame for a Arcade Fightstick. It requires a large printer since the full dimension is close to 30*21 cm. I used a metal plate to close it, as long as some screw for closing the stick ( at least on must be short to avoid…
** Update from 11/Sept/2018 New version A lot of sizes corrections and position adjustments Adding space for GG Everdrive micro SD card Adding pegs to clips the to parts Adding TOP variations: a simple without logo, a SEGA and a Krikzz…
This is the housing for a Super Nintendo AV connectors PCB I've made. The connector is a drop replacement of the original connector. The PCB is hold with a M2.5x10mm screw. This is a great combination with Borti4938's NES I/O panel. You…
Here's a bezel for the Madcatz TE2/TE2+ . It's hard to find them so why not DIY? Since it's a big part, you need to assemble it. Mines were printed on a Kossel Linear Plus. Straight part is long but should fit in most 3Dprinters. You need…
This part tends to break easily. I made a replacement in two parts. I strongly suggest to do a 100% fill for the main part, and use a clear filament for the second. Note: you need to melt the 6 prongs of the logopart after mounting it.…
Here's a drill guide if you want to use a SNES Multiout connector with a Virtual Tap on your Virtual Boy. Dimensions are for fitting Laser Bear's Panel Mount Snap-in Multiout (check his website here…
This is the small part which is going on the back of the D-pad on a Dual Shock. Note: The part is thin, not sure if a FDM printer can print it. Category: Video Games
Here my version of the enclosure for a SuperGun Minigun. There's multiple variations: a 2 parts (Full and Bottom) a 3 parts (Top, Frame, and Bottom) Each have version with holes on the top or not if you want access to the RGB/LowPass…
Replacement of the D-Pad for the Hori Fighting Commander 4 with microswitches. You need : The top and bottom 3D parts, PCB should be in 1.6mm, 4 Microswitches (recommand omron D2FC-FK(50M)), Male 5 Pin JST PH Connector,…
I was looking for a cheap boom-mic arm, but they either good quality and expensive, or cheap and a bit crappy. After looking on the Vesa arm mount, I design this adapter, so you can put any cold shoe adapter (such as flash) or with a 1/4…
This support is to avoid the NESRGB PCB from eTim (Tim Worthington) floating when you install it in a Front Loader NES. No screw needed, just put it on the side of the board. It's designed to avoid the components. Category: Electronics
Here's some wall stands for the gscartsw from SuperG, where you can just slide it in. I took in count both plexiglass and the small rubber pads for the height, so it should just sit nicely. You need at least two of them, up to 4 to…
The switches support of my range hood BROAN QP130WWC litteraly broke down like a chocolate barre. After looking for a replacement, the part number is S97017729, and since I'm a cheap bastard, rather than pay 25ish dollars plus shipping…
The top of my cheap dicer bought on Amazon (branded as "Lyizci") broke after the 3rd use (link amazon https://www.amazon.ca/Vegetable-Chopper-Mandoline-Container-Choppers/dp/B09NLS4B51 not affiliate, just as a ref to see which model I'm…
I have a Billy as a frame for my custom computer desk. I needed a holder for my headset and other cables. So here it is. Category: Organization
If you have de Madcatz TE, SE or TES+, this quick connect board is supposed to help you link the buttons to the main PCB. However if like me you're modding stick, it's possible other peope get rid of this thing. Here's everything you need…
Top filament spool holder for my Anycubc Linear Plus. This is similar to other spool holder you can find here like: https://www.thingiverse.com/thing:1989704 Two parts to fix on the top, the middle just clips between as a bridge, the…
Change the orientation of the Retrotink 5x. See project on Github/OSHPark for the PCB. 2x M3*10mm screws for the PCB 2x M2*5mm screws for enclosure https://github.com/TRP-Retromods/SCARTFlip https://oshpark.com/shared_projects/eteopb15
Here's a feet cap compatible with the Chiron Feet Famper here: http://www.thingiverse.com/thing:3225296 You may add a bit of double sided tape to hold the feet. Category: 3D Printer Parts
I didn't want to drill holes on the wall in my basement for the center speaker. So I made a stand which you can put on the top of your TV like a webcam. I used an acrylic rod for the main articulation but you can 3D print it. I used two…
These are all currently available results.
