P
PrintablesDrakarah
Voron 2.4 nozzle brush using Bambu Lab's A1 silicon brush (Formbot kit)
With my formbot kit the brush was 7mm too wide and 3mm too high, and now it sits flush with the bed and the bucket.
- Downloads
- 127
- Likes
- 12
- Rating
- 0
All models
Counting matching models…
P
PrintablesDrakarah
Brackets for Z umbilical with PUG
There are other solutions but I couldn't really find one that uses PUGs and didn't have the toohead umbilical routed so I made my own clamps. The bottom clamp can be used on the gantry side as well if you don't have the wires routed in…
- Downloads
- 102
- Likes
- 22
- Rating
- 5
P
PrintablesDrakarah
Fysetc Hexa Distro Fusion backpack
Backpack for the Fysetc Hexa Distro Fusion board. Interfaces with N3mi Umbilical Exhaust plates v2 ( https://github.com/DraftShift/CableManagement/tree/main/UserMods/N3MI-DG/Umbilical_plates_V2 ) Uses a PUG for cable strain relief…
- Downloads
- 85
- Likes
- 24
- Rating
- 0
P
PrintablesDrakarah
EBB36 v1.2 CW2 mount with PUG
Update 2025-08-05: I've made some small changes: The bolt holes are now in the middle of the retainer The bracket mounts EBB36 1mm higher to prevent the backside through hold solder joints from interfering I've also designed a wire cage…
- Downloads
- 60
- Likes
- 12
- Rating
- 5
P
PrintablesDrakarah
Formbot LED bar holder with slit
I already routed the wiring, didn't want to cut or resolder, so I added a slit to push the wire through
- Downloads
- 47
- Likes
- 5
- Rating
- 0
P
PrintablesDrakarah
Stealthchanger shuttle Z endstop
See https://discord.com/channels/1226846451028725821/1401451184723595264
- Downloads
- 26
- Likes
- 8
- Rating
- 0
P
PrintablesDrakarah
Drag knife toolhead - compatible with StealthChanger backplate
I wanted a vinyl cutter for my StealthChanger build, I wrote about it https://github.com/drake7707/Drakarah3DPrinter/blob/main/journey-to-stealthcutter.md if you want more details how to use the toolhead
- Downloads
- 23
- Likes
- 15
- Rating
- 0
P
PrintablesDrakarah
Wago CAN distribution box for N3MI Umbilical plate
Uses a PUG for cable strain relief https://www.printables.com/model/378567-pug-parametric-umbilical-gland Uses https://www.printables.com/model/506687-wago-221-415-mount to mount wagos. Mounts into…
- Downloads
- 21
- Likes
- 7
- Rating
- 0
P
PrintablesDrakarah
Bambu nozzle brush with tray between The Filter bed fans
I wanted to add bed fans with The Filter but that meant my old Nozzle wiper was in the way, I positioned it to be on top of the extrusion and designed a tray around it that does not interfere with the fans of The Filter. Update: made a…
- Downloads
- 21
- Likes
- 5
- Rating
- 0
P
PrintablesDrakarah
Large yarn bobbin
Bobbin to keep multiple strands organised in your workpiece
- Downloads
- 19
- Likes
- 3
- Rating
- 0
P
PrintablesDrakarah
Tough latches with space for 1.8mm dowel pins
Despite the dowels being advertised as M1.5 they were not 1.5mm diameter but closer to 1.7-1.8mm I remixed both 4mm and 6mm versions by punching cylinders through the holes to cut a wider hole in FreeCAD. Probably not the best way to do…
- Downloads
- 16
- Likes
- 0
- Rating
- 0
P
PrintablesDrakarah
Fly D5 side backpack
I'm using a Fly D5 as a motor board for my feeders and this is the mount I created to mount it to the back of the printe
- Downloads
- 9
- Likes
- 1
- Rating
- 0
P
PrintablesDrakarah
Clockwork2 filament feeders
Use the bracked to mount them to the top extrusion Use cable clips to clip the mess of wires in a cable shroud to the extrusion to route it to the board.
- Downloads
- 9
- Likes
- 3
- Rating
- 0
P
PrintablesDrakarah
Vine holder
I wanted to route my vine-y plant along the ceiling lights in a more fashionable way than just a piece of string and a washing pin, so I designed this. I wanted to make it modular so it would be easier to print and assemble Uses heat set…
- Downloads
- 8
- Likes
- 2
- Rating
- 0
P
PrintablesDrakarah
Annex belay array mount
Mount for belays to the side extrusion
- Downloads
- 8
- Likes
- 3
- Rating
- 0
P
PrintablesDrakarah
Flute/kalimba hooks
I used 3M double sided tape, works well, had to iterate on the hooks a few times to make sure it could carry the weight, the load had to be in the middle so the plastic didn't flex and peel off the wall. Hooks of the kalimba is matched to…
- Downloads
- 6
- Likes
- 1
- Rating
- 0
These are all currently available results.