Counting matching models…
I needed a three way connector for my X1C when using the AMS, an external spoolholder and a Filament drybox. This is the design I came up with. For external parts you need 4x PC4m10 bowden tube connector. Make sure you have the connectors…
Housing for ESP32 Cam modul (Tinker board) Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0,2 Infill: 100% Notes: After printing you can use female breadboard connectors with the plastic…
A potato slicing tool to make nice potato spirals for the deep fryer. Printing: The Cutter is printed in PLA with 0.16 mm layerheight The handle is printed in PLA with 0.2mm layerheight Usage: You need a metal pike with 2mm diameter. Put…
Primary I designed this Hexagon tile set to hide my cables from the TV. So there is plenty of space for cable management behind the tiles. There are four eyelets on each base plate for using zipties. Since the Tiles are featureing magnets…
Simple ID-Card / Key-Card holder. Fits standard 86x54mm key cards. must be printed with supports (enable supports on print plate only)
With this handy little tool you can clean your carbon rods even when the lid of your bambu printer is closed. Just put Isopropyl alcohol on the sponges, snap it to your carbon rod and move it back and forth a few times till they are shiny…
Router Radius Jig / Template with mountable holder R5, R10, R15, R20, R25, R30 Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Infill: 40% Category: Hand Tools
This is a scaled flyable micro version of the ASW20 sailplane from Schleicher. The model was created to be lightweight and printable in normal PLA. Because of it's lightweight behaviour it's a little bit fiddly to get it together properly…
Micro Reverse Compound Crossbow Really fun for shooting on a magnetic dart plate. The parts are printed in PLA and PETG at 0.2mm layer height. Additional Hardware: 2 mm wire (I used a 2mm stainless steel tig welding rod) magnet D:6mm…
The model consists of two parts: shovel handle It can be printed without supports if you orient it like shown in the picture. The connection between the handle and the shovel is a tight fit. Optionally it can be glued in place with some…
Not another Heli launcher! But this one is different, it features an 1:9 gear System for full Power supportet by 608 ball bearings. External Hardware: Assembly Press Bearing Press a 608 bearing into the hole of the middle housing. This is…
This flying Bat prints with 0.2mm layerheight and 100% Infill. The 100% infill is needed to make sure the center of gravity is in the right spot. After the print you have to fold the wings like in the pictures. You can use a lighter to…
This is my first prototype of a reverse compound micro crossbow. After Printing there are some problems with the clearances. On the triggermechanism some holes have to be drilled out to work without friction. Also there is some sanding to…
Drum sanding attachment for your powerdrill. External Hardware: 2x 608 Bearing 1x M8 nut 1x M8 threaded Rod (90mm + Drumheight) Print Settings: 0,2mm Layerheight, 4 perimeter, 20% Infill Assembly: Add 608 Bearing to the upperside of the…
HUGHES MD - 500 (flyable pullcopter) Externals For launching the MD-500, you need to make the “ Overpowered Heli Launcher ” before: Printingsettings Print as light as possible. I used 2 perimeter, 0.2mm layerheight and 10% infill on the…
Propeller toy in the shape of a flying saucer. Fun toy to play. Even with more weight than the normal propeller it still flys very high. On the shown GIF I didn't pull the rack all the way because I didn't want to demage my ceiling but…
Quantity Walls 2x Connect 2x Caps 6x Marker 1x Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: No Resolution: 0,2 Infill: 30% Grey Parts, 100% White parts Category: Hand Tools
print in place leverlatch for all kind of boxes and furniture doors. no need for supports print it in the given direction with a little force you should be able to break it free after bed removing Print Settings Printer Brand: Creality…
Low Profile Spoolholder for sidemounting to the bambulab AMS. With the bowdenconnector it adds just 34mm to the AMS in width. Fits spools from 140 to 200mm diameter. Never unplug the AMS again when printing from an external spool.…
Keep your spices always with you. This little container wich can be filled with any spices you want, fits on a keychain ring.
Wallmount for Ryobi 18V ONE+ 25-30cm cordless grass trimmer. The Wallmount also features a holder for the sense trimmer blades, an extra spool and the sense trimmer adapter. Printing: Print Flat on the Build Plate and enable supports.…
Mosquito Net Magnets. Magnets size: D: 6mm, h:3mm the Magnets are pressed into the holes and locket with ca glue. The Windowmagnet can be ca glued on a strong adhesive tape, wich is then glued to the window frame. The mosquito net is…
Storage box for ER20 collets. Also included is an Gridfinity Insert for the storage box wich also uncludes space for 2 wrenches.
Featherboard for the circular saw for mounting on the fence and the sliding table on a Felder/Hammer K3/B3
Spool holder for frictionless spool rolling. use with 608 Bearings Category: 3D Printer Parts
608 Roller bearing adapter for router sled Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: Machine Tools
Throttle with 7 Axes and 24 buttons (32 -> 2 HAT Switches) This project uses an Arduino Micro and 2 MCP23017 shift register for all the buttons. Since I am very lazy on documentaton i added the step file also. For the electronic part just…
Dowel Jig for 8mm dowels Adapter Plate to fit 25, 22, 19 and 16 mm thick material. For the drill hole you need 2 608 bearings. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0,2 Infill: 40%…
Now you can transport your delicous egg without the fear of crushing it! Printing: This is a print in place model. Activate supports, but block it on all the hinges, otherwise they can bind up. Postprocessing: Remove the supports and…
Found this Idea in the video of pocket83 and had to do a 3D printed version of it The model prints without supports if you use 0.2mm layerheight. For furhter hardware you need at least 2 M5x20mm hex nut screws. You can screw them directly…
This is a spring suspended drag knife holder for the CNC machine. It fits directly into the spindle with an SR20 collet. It's made for this cheap "Roland Drag Knife Holder" https://www.amazon.de/gp/product/B09DSHZH5F/ The spring…
This cat flap fits to your mosquito screen door. External Hardware 24pc - M3 x 12 mm Counter Sunk Screw 24pc - M3 x 6mm Brass Heat inserts Installation Add the brass heat inserts to the bottom frame by putting some Superglue to the…
angle grinder holder for pegboard with 50x50mm raster and 8x15mm holes To tighten the pin, you need a 3x18mm woodscrew. For the older Makita anglegrinder you have to print the legacy version, for the new one you have to print the 30mm…
Hose Adapter for Vorwerk Kobold VK200 Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: Yes Supports: Yes Resolution: 0,2 Infill: 20% Category: Household Supplies
Invisible mounting bracket for mounting a shelf to the wall and get this floating shelf effect. For alignement there are two holes wich fit an M3 heat insert and some M3 screws If you are using a CNC for milling the space for the insert,…
Tray for the Wrench and the Allen keys for the sawblade change on your Hammer K3/B3. Mounts under the sliding table. To fix it in place, simple use double sided tape.
Tungsten electrode grinder for tig welding fitting on a dremel tool. The parts can be printed without support. in addition you will need 4mm thick acrylic glass. you can use the standard adapter for the electrodes, but this will melt if…
The 3D printed CNC Plotter Penholder is a specialized attachment designed to convert a CNC machine into an accurate plotting device. It mounts onto a 62mm spindle motor (2.2kW) and accommodates a standard ballpoint pen mine. The penholder…
A little container in the shape of a bowling pin which can be unscrewed to hide stuff in it. Printed in 0.12mm layerheight
Fidget RotaryClickSpinner Spinner with two magnetized rotary knobs and a very satisfying ratchet mechanism. External Hardware: 1x countersunk screw M2.5x12mm 1x countersunk screw M2.5x20mm 2x M2.5 x 4mm brass heatinsert 2x 608 bearing 14x…
Spice bottle with openings on both ends. Print Settings Printer Brand: Creality Printer: CR10S PRO Supports: No Resolution: 0,12 Infill: 100% Category: Household
Organize your keys like a swiss army knife. You can either print the version or if you have a CNC mill you can make a milled version of it. the dxf for the milled version is provided. For the printed version you need two M4 bolts and two…
This is a tactical laser attachment which fits on your Bug-A-Salt 3.0. Read the Instructions before you print anything! External Hardware: Printing: The front plate print features an mid print insert. Print out the provided…
Cat Collar for holding the Samsung Galxy SmartTag2. The Cat Collar features a safety latch which opens at about 4kg of pull in case of the cat get stuck somewhere. Measuring: Measure the circumference of your cats neck to get the right…
Holder for the Nozzles of a solder rework station Fits Nozzles with 22mm inner diameter. Uses magnets with 6mm diameter and 3m thickness.
just a hook to store your clothes horse to the wall Fits for <6mm diameter screw and clothes horse with 15mm diameter pipes
Print in Place hose adapter for Einhell TE-VC 1925 SA (TH-VC 1930 SA) for 38mm hose (outer diameter 46mm) Without guarantee (i just have the TE-VC 1925 SA) but i think it should also fit on TE-VC 2230 SA BT-VC 1500 SA YPL N.G. 1500 BT-VC…
Neje A40640 laser air assist with optional safety. Attention: even if the guard blocks most of the light, you still have to use goggles for your own safety. Don't print the guard too big, because the smoke still needs some gap to escape.…
Chilli Bottle to Go Small Bottle for spices like chilli Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0,12 Infill: 100 Category: Kitchen & Dining
Mosquito Net Magnets. Magnets size: D: 6mm, h:3mm the Magnets are pressed into the holes and locket with ca glue. The Windowmagnet can be ca glued on a strong adhesive tape, wich is then glued to the window frame. The mosquito net is…
Holder for the heat inserts insertion helper tool. Can be mounted with two screws to the wall. Print it in standing position otherwise the clamp may fail If the clamp is too tight for the soldering tip, you can heat it a little bit and…
For the pikes you need a 2mm stainless steel rod cut to ~30mm lenght. I used a stainless steel tig welding rod. For sharpening you can put the pikes into a drill and use an angle grinder. The holes are a little bit undersized to guarantee…
welding helmeht holder for pegboard with 50x50mm raster and 8x15mm holes To tighten the pin, you need a 3x18mm woodscrew
Since the original holder for my Bestway Flowclear Skimatik skimmer was too bulky and too long for using it with the Hottub and closing the cover was also not possible with it, I had to design a new hook for it. For the threads on the…
A simple diy solution for MQL(Minimum Quantity Lubrication) part cooling for CNC machines. For external hardware you will need: Pressre reducer 4mm PTFE Connectors 4mm PTFE Tube 2mm brass pipe 4mm brass pipe Teflon Tape Corona Test Bottle…
Slider with 608 bearings wich can slide on a 6mm glass panel. Wheels are printed in TPU. Hardware: 2x 608 bearing 2x M2,5 counter sunk screw 2x M2,5 brass heat insert
A Touchprobe for CNC in normally open mode made from an PT31 plasma cutter electrode and nozzle and a spring. Can be mounted directly into the spindle for Z-probing the workpiece surface. Since the isolator part between the electrode and…
just a simple hook for securing your bike in the car for save transport. The hook should be reinforced with a 2mm steel rod
Fidget toy with spiraling balls moved by magnets. It is a print in place model, where you have to pause your printer to put the magnets and the balls in. Additional hardware: 3 x 4mm steel balls (can be found in 608 bearings) 3 x 6x3mm…
Intake for a Laserbox for blocking the light and letting the air in Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0,2 Infill: 20% Category: Parts
simple model for storing batteries in all sizes.
Holder for mounting a huawei b593 router Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: Electronics
replacement button for thermoplan s'whipper cream machine wich was broken.
These are all currently available results.
