Counting matching models…
Remixed. Includes button tab integrated into main unit. When printed with flexible material, flexes to allow button to compress. Used Goop glue to secure to Edge. Requires trimming back of white casing to fit. Printed with NijaFlex…
Picked up a Press Play universal phone mount and modified with this insert modelled after the ND2 (likely the ND) cup holder inserts. The top insert area is specific to the Press Play phone mount but can be easily modified. Props to…
You can use this to hold 2 LED's and mount it on your quad. Low profile and light. More cool stuff @ http://www.plastibots.com This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/aYbwqSqHA3W Category: 3D…
A nice 3rd hand option to help with soldering and other electronics work. Magnifier adapter is a crude unit. Idea is you get a magnifying glass, cut the arm down and glob the glue in to merge the two. The other end of the adapter fits the…
Skyline 5862 Mini Helicopter Tail rotor. More cool stuff @ http://www.plastibots.com This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/fhT1pHS5CVq Note - the center pin hole is ~ 0.70 mm in diameter is…
This is a 5" bezel you can use for the Nextion display. For details and pictures on how this was used, visit www.plastibots.com. It allows for the mounting of the display flush on a wall with only a need for a hole near where the serial…
A remix of the Adafruit Pi stand for 3D Printers. I added a power switch. Both parts were glued together using Goop. More details at http://www.plastibots.com/index.php/2018/06/02/adding-tft-lcd-to-raspberry-pi-octopi-rig-touchui/…
Needed a mount for my Logitech C270 and LEDs for monitoring / recording prints using OctoPrint. Note, this requires a mount for the C270 (or your IP cam) as well as an interface to the mounting arm. I used flex arm parts and did some…
Remixed. Original part fit is for iPhoneX. Also note that it fits small for the silcone case I have. Instead I use it without the case and add elastics to hold it in place. Opened up middle area to allow access to phone control (camera…
A case for mounting the Sparkfun Fingerprint Scanner outdoors - https://www.sparkfun.com/products/11792 Check out my IoT Garage Monitor Opener Project here:…
Full write-up at www.plastibots.com. 3D printed parts for my WIOT weather project and IoT Blynk notifier. Consists of the following: Controller unit baseplate and cover (both connect together and cover can swivel open/closed. Main unit -…
These are the files for the custom Arduino fan controller case I built for my LulzBot Mini. Full write-up, schematics, parts and code are at…
This allows you to mount the FatShark TVL600 (or similar) FPV camera so it can be rotated by a servo on the FeeYoung ZX-250 quad frame. The flange is printed 0.2mm wider with a 0.5mm support. Once printed and cooled, you have to twist the…
This is based on the assumption that you have a Quattro (or similar) 4in1 ESC mounted to the bottom of your quadcopter. It houses a bubble level and holds the quad in place for calibration of the accelerometer (or just working on it).…
Low profile base mount for flip32 or flip32+. http://www.banggood.com/Naze32-Flight-Controller-With-32-bit-STM32-for-Multicopter-10Dof-p-953849.html?p=R90804949020201412E4 More stuff at http://www.plastibots.com This thing was made with…
You can use these mounts to hold a set of small ESCs in place on your quad. These were made for a FeeYoung ZX-250 frame and mount the FVT LittleBee 20A ESCs. However, they may work for others. Requires glueing.. Hot glue or Goop (my…
These are all currently available results.
