Counting matching models…
This is a replacement for the air stripper and baffle assembly on the Umarex Gauntlet pellet rifle. Prints in one piece, muzzle-end-down with no supports needed. I saw a noticeable decrease in firing noise after replacing the factory…
I needed a spot for my headphones, so I designed this to hook onto the triangle mesh in the front of my 4000D airflow computer case. It should fit any other Corsair computer case that has the same triangle mesh (which is quite a few). I…
I needed a desiccant container and none of the designs I found online met all my needs in terms of shape, dimensions, and ease/speed of printing, so I decided to design my own. I took inspiration from PsychProd's in-spool desiccant…
This is a panel mount for a pair of Amass XT-30 connectors. I needed a way to mount one male and one female XT30 to a panel for use in a large power bank, one for charging the internal battery, one for supplying power to external devices.…
Most flashlight clips/holsters I've seen have the flashlight vertical, which tends to make them dig into one's side when sitting down. This one has the flashlight sit along the belt, which is more streamlined. I use it for my EDC every…
Got sick of my shower curtain falling off the open rings it came with, so I made these. They're print-in-place and stay shut pretty tightly. I've included versions with 0.25. 0.3, and 0.35mm clearance, so you can find the one that prints…
I use a Nite-Ize #3 locking S-biner on my keychain, and one of the little plastic locking slider pieces went missing. Rather than buy a whole new carabiner, I designed and printed a couple of these replacement sliders. It's slightly…
A minimalistic and quick-to-print mount for a Rift CV1 tracker. Designed to be stuck to a wall with 3m Command Strips or a similar double-sided tape.
The XT90-shaped hole in the original was off center. This one is not. Category: DIY
Adapts from a generic DIN rail clip (three holes in a line, 0.5"/12.7mm spacing) to Mesa interface cards for my CNC machine conversion (94mm hole spacing). Prints without supports but needs bridging on the top, the best solution I found…
I bought a rubber jack pad online, which turned out to be too large to fit nicely on my jack. I designed this to print out of TPU and snap onto the jack, and then the jack pad slips over the adapter. I printed it from 95A TPU with 90%…
Spacer to widen an MBS wheel hub. Best printed in something tough and impact resistant like nylon or ABS/ASA, but PETG would probably be fine too. Once installed it's backed up on both sides by the hub halves, and under compression from…
A modular electric skateboard battery and vesc enclosure. Suitable for flat packed battery packs. Can be arranged in multiple ways, such as 5, 7 or 3 piece arrangements for different length decks. Standard design was intended for 40"…
One of the tools I carry with me almost every day is a precision 4mm bit driver, and various driver bits to go with it. The driver originally came with a holder that attached right to the driver itself, but it eventually broke and I…
This is a recreation of the Cetus Mk2 standard Z-axis endstop holder. When mine broke, I searched online and found a set of files for most of the printed parts on the cetus, including this piece - except it's wrong. I printed the version…
I found these neat circuit boards designed for an 18-watt 5v/9v/12v USB-PD power bank, and decided to design a shell to hold one of them, and two 18650 li-ion cells. It has a recessed button to avoid accidental activation in a pocket or…
This is a minor remix of LUCKYCO's FlyGun to make the piston seal more effectively and with less friction than the original. All the same files as the original are untouched (and not provided here) except numbers 15, 16, 18, 19 and 20…
These are all currently available results.
![XT-90s Loop Panel Mount (Small) [remix]](https://media.printables.com/media/prints/196361/images/1817579_201e6a6a-41e6-4033-b3f5-1c63fc058215/large_display_xt-90-s_panel_mount_sm-fixedstl_196.png)
