Counting matching models…
Video of this in action, with context: Check out online recipes for making the mixture, using sawdust, potato starch, etc. A PDF is also attached here in the files section, with the recipes from the linked video. This print is done in 3…
Simple spacer washer, M3 size. On the Ender Extender, I needed to space the Y limit switch away from the adapter bracket that was provided due to the through-hole solder blobs clashing with the bracket. Two of these on each screw solved…
Simple tool which slips over the injector, and then you shove the straw from your injector cleaning solution on the other. This is designed to fit over a standard Bosch EV1 or EV6 type injector with ~14mm nominal O-ring size. Use a hose…
Remixed from this CR-10 tensioner on Thingiverse. It is perfect for the Ender Extender converted Ender 3 (Pro and non-Pro). When you installed the Y-axis tensioner from your Ender Extender kit, they gave you a longer M8 bolt. This kit…
This houses 4x lithophanes, each one should be 100mm x 100mm x 4mm. They are sandwiches between the 2 halves, and you use M3 screws to hold it together. The backlight plan was designed for a 1m LED strip - this wraps around the center…
This is a simple bracket to offset the PSU off from the Z-axis upright, making way for a 2nd lead screw. It mounts to the 4040 extrusion using M4 screws and T-nuts. Print it with the side which faces the PSU facing down on the bed. No…
I didn't want to pay $200+ for a Sir Tools P234 arbor so I whipped this up. I sell these for $15 if you do not have 3D printing capability, but I am offering it (for NON-COMMERCIAL usage) here. That means you are not printing these and…
If you have a CR-Touch, the Satsana remixes that have the integrated BLTouch mount will NOT work! The position of the wiring connector is right between the 2 mounting screws. This is also for the Ender 3 V2 using the Micro Swiss Direct…
Based on the excellent Y-axis belt tensioner by donnyb99 on Thingiverse , for the CR-10 originally. However there are some changes: Added holes for a T-nut on each side, since the original design is wobbly. I didn't have any M5 hex bolts,…
Partially original, partially remixed (attributions later in this section). Provides a solid dual-Z conversion using parts you may already have laying around, or are at least cheap and easy to get. This was for my Ender Extender converted…
Based on this model by Passat250. I shaved the top so the fan shroud wouldn't smash into it during homing. The spacer is in case the Z-axis carriage clashes with the back of the drawers. You can use this spacer between the back of the…
This slips onto your extruder stepper shaft (with the flat machined into it) to act as a knob. Ender 3, Ender 5, etc. Very detailed Fuchs model, recommend a 0.4mm or smaller nozzle and fine slicing. You will need supports: print this with…
The front speakers need to fit a very specific profile, which is unfortunately not common. Most 4" x 6" speakers will slightly interfere with either the sheet metal cut-out dimensions, or they protrude too deep, so they clash with the…
This is an organizer for seed packets, that may be larger than the ones at local hardware stores. For example, Baker Creek uses a larger size. The top isn't hinged, it just slides onto a ledge. Uploaded the Solidworks files as well, if…
Remix of sirhc's case found on Thingiverse here . This is optimized for mounting on the side of your printer, either on a 2020 or 4040 extrusion. M3 screws are used to join the two case halves. The mount installs to the lower half using…
Uploading this to address 2 issues with the status quo, affecting any 924 or 944 with the steel front control arm design. Note that this is discussing the outer bushing, at the control arm. Stock rubber bushing will only work with the…
This converts your transaxle linkage to a thrust bearing design. Has been installed on our rally car for over a year and has been perfectly fine (printed in ABS - see more info in printer settings section). Installation instructions are…
Secure saddle for a typical 2.5" hard drive on a RVL-001 Wii. Simply print 2x of these brackets, and use M3 screws to attach to the threaded holes on the bottom of the drive. There is also a (decorative) top cover for the drive. One…
Cover the area where the distributor used to go, using this part. There are 2 version uploaded: One is designed for using thread inserts with. One is designed for using M6 heat-sert / knurled nut inserts (as seen in pictures). The OD of…
This is a modification for an Ender Extender (400 x 400) with the AC heated bed. The original strain relief included with the kit started to droop / creep after a few months of use, and I did not feel this would adequately protect the…
I originally started selling these in 2022, but decided to release the files for free. PowerFlex blatantly copied my design in 2024, so now there is very low demand. So, as a gesture to PowerFlex (perhaps a gesture involving a certain…
The Ender 3 V2 screen doesn't work with Klipper (at the time of this upload). There's a way to connect the RPi GPIO pins to it and get it to at least display a few things, but it was buggy for me and kind of crap overall. So I made this…
I was tired of clamping the accelerometer onto the edge of the build plate so I made this. You will need the following: 2x M3 screws, roughly 5 to 10 millimeters should work. ADXL345 accelerometer. Magnetic adhesive sticker, trimmed to…
Add a 7" touchscreen to your Ender 3 V2 with this printable mount. You need to flip the top and lower sections upside down in your slicer to avoid supports! Sorry, missed that in Solidworks. Native SLDPRT and STEP files also included. Top…
If you have installed the Ender Extender 400 kit, this fills in the huge empty space on the front right of the printer with a useful storage bin. It mounts using M3 hardware and T-nuts; there is room left for the display ribbon cable to…
Obviously a multi-material print, unless you want to paint it. You can add a magnet strip to the back. If it's going on your car, ASA is the best choice.
This was originally a project for adapting a Megasquirt 3 Pro (Gen 1) ECU to the mounting panel in my 944 Turbo. It's called the Megasquirt Interface & Layout Frame (M.I.L.F.) However I'm uploading a few different versions, so others can…
You can cover the QR code on your Ender 3 or CR series printer with this. It should also fit over standard NEMA 17 stepper motors, however you'll likely have to cut a small opening for the electrical plug on 1 side. Suggest printing with…
I had a cheap Sabrent HB-MCRM USB hub (4-port) to fix the problem of my Orange Pi Zero2 only having 1 USB port without getting an expansion board. I printed with TPU and this works well, however my edges came out a little sloppy due to…
This is intended to fix the issue where the lower dish rack wheels pop off when you open or close it. Instead of relying on the push-clip style retainer, it is converted to a bolt + lock nut for each wheel. Good luck falling off again!…
These are all currently available results.
