All models

Counting matching models…

Ukelele Wall Mount (no screws)

I wanted to mount my ukelele to the wall, but I can't drill into it. So I made this mount which used 4 3m command strips from costco.

Downloads: 79
Likes: 26
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Keyboard Slider Knob (Yamaha Montage 8)

I needed a replacement knob for the yamaha montage 8. Plus it was a good excuse to add a bit of color to the design.

Downloads: 54
Likes: 8
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Bowling Ball Mold (cement)

I designed this mold for making a concrete bowling ball for a competition.

Downloads: 45
Likes: 14
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Potentiometer Knob (Yamaha Montage 8)

I needed a replacement knob for my yamaha montage 8.

Downloads: 38
Likes: 7
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

I wanted a pellet press like the one NileRed uses in his superconductor video, but they were too expensive for me. The first one I made (not shown here) was PETG at 100% infill and it was able to survive up to 12 tons, but now I'm testing…

Downloads: 20
Likes: 1
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Breville Portafilter Handle

This is a replacement handle for a breville portafilter. I used PETG for this, but I will switch to Polycarbonate IF the heat from making espresso ends up deforming the handle.

Downloads: 17
Likes: 3
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Screw jack protective Pad

I made this to avoid scratching the stuff I want to lift with this screw jack. This may involve heavy equipment, so use at your own risk.

Downloads: 11
Likes: 3
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

UwU Car Badge

I designed this for a toyota scion. So the font and letter sizing was as close as I could get to the original style of the badge for the car.

Downloads: 10
Likes: 0
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Car Jack Wheel (Duralast 3 Ton Low Profile)

The inner part is made with PETG, and is pretty much all walls and no infill, while the outer part is TPU and is 50% infill to allow for some squishing. Since I wanted a tight fit to avoid using glue or epoxy, I needed to use a rubber…

Downloads: 6
Likes: 0
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Manna 64oz Bottle Cushion

I made this because I was tired of having to be extra careful when placing down my water jug while in quiet places.

Downloads: 4
Likes: 1
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Scosche Iphone Holder

This is for a scosche magsafe phone charger. I use it with the airvent holder. It is sized to an iphone 13 pro max without a case. I printed it in PETG at 30% infill to avoid deformation from heat inside of my car. The back part is…

Downloads: 3
Likes: 0
Rating: 0

Order a print of this model

PrintablesArturo Pizarro

Screw Jack Drill Attachment

I made this drill attachment to power my screw jack. I have yet to test it under load, but I plan to use it when lifting a piano. Since this deals with potentially heavy and dangerous machinery, use at your own risk.

Downloads: 3
Likes: 0
Rating: 0

Order a print of this model

These are all currently available results.