Counting matching models…
I accidentally dropped my wolfbox blower with the long nozzle attached, and managed to break one of the sliding tabs on the bottom that lock it into the base. So I grabbed some calipers and opened fusion 360 and got to work! 😆 I decided…
The lever on the battery door of my Olympus em5 mkii broke, so what's a guy to do? Why, model a replacement, of course! I'm not sure if other Olympus camera bodies use the same lever or not, but it works with the em5 mkii at least.…
Sometimes when using the shaper origin in tight spaces, the vacuum hose can stick out and get in the way. This is a 45 degree elbow adapter that allows the hose to come out at a less obtrusive angle. It's not recommended for continual…
A 5x5x5cm weighted companion cube, designed specifically for the Prusa Multi-material printer. After receiving my Prusa Multi-material upgrade, I needed a project to get acquainted with multi material modeling and printing. This is that…
Just a little feeding bowl I designed to put in one of my roach bins. The flat part goes up against a wall, and the sloped sides allow easy ingress/egress, while keeping the food in place
NOTE: I've uploaded a newer version that is optimized for semi-flex material, and uses openSCAD, for ease of customization. https://www.printables.com/model/207250-integral-mesh-vent-cover-v2 --- This is a mesh vent cover that can be used…
This is a 3d printed mesh that can be set into a deli cup with a layer of plaster on the bottom, to form a compartment with spaghnum moss, for culturing springtails. I've used this setup with great success for many species of non-arid…
This is an updated version of my original vent cover. This one has been converted to openSCAD for ease of modification/customization. The default values are also optimized for a vent that works well when printed in a semi-flex material.…
This is a hide meant to hold moist sphagnum moss, for use in a low-maintenance arid springtail enclosure. It is sized for a Karat 8oz clear PET deli cup to fit onto. (e.g. https://www.amazon.com/dp/B0BT9HYYPR ). For an arid springtail…
This is an adapter that screws into the trinocular port of a Swift SW380T microscope, with a component that can attach to a micro 4/3's camera (e.g. modern Olympus cameras). It may work with other Swift or other brands of microscopes that…
A suspended feeder for feeding slime mold to slime-feeding springtails, for a 16oz deli cup. The feeder is attached to the wall of the deli cup via magnets embedded in the print, and a couple of magnets adhered to the outside of the cup…
This is a modification of the magnetic handles and base for Dominik Císař's Prusa enclosure ( https://www.thingiverse.com/thing:2864118 ). I tweaked the design to use some 1/2" x 1/16" disc magnets that are readily available in the U.S…
A suspended feeder for feeding slime mold to springtails, for an 11.8 cup mainstays tritan food storage container This should be printed with supports enabled. This rests on a small lip near the top of the container, but for best results,…
A suspended feeder for feeding slime mold to springtails, for an 8oz deli cup. This should be printed with supports enabled. The idea is that you suspend the basket over the substrate and place slime-mold covered oats in the basket, and…
A suspended feeder for feeding slime mold to springtails, for a 16oz deli cup. This should be printed with supports enabled. The idea is that you suspend the basket over the substrate and place slime-mold covered oats in the basket, and…
This is my knob design for a Nerdy Gurdy . It is comprised of 2 parts which screw together near seamlessly. You can barely see the seam, and can't feel it with your fingers. You can barely even feel it with your fingernail. It only needs…
A modular stand for holding the widely available 5ml plastic vials. It can be placed horizontally on a flat surface, or vertically with an additional base part. The clearances are pretty tight on the dovetails. It works well on my printer…
These are all currently available results.
