Counting matching models…
Filament Roller, this design uses 4x 626Z bearings and two carbon fibre tubes to join the sections. I originally design this using rolled carbon fibre tubes that I had spare as it looks far superior but yo can use the STLs to print your…
UPDATE 13/1/19 Sorry to all who I have tried printing this and then realised i screwed up the instructions on the use of supports. The side part does indeed need supports, as there is are cylindrical parts that extends out from the side.…
This is a model I designed as a cake decoration, I have split the sail in to 2 sections that can be printed flat and then glued together and dropped in to the hull. When I designed this I intended to resin print the hull and FDM print all…
Use standard Prusa slicing.
This is designed to hold a Phantom 4 battery on a different drone. The mounts are designed to fit 10mm rails at roughly 60mm apart. This is designed to take a DJI P4 power board that sits on lugs at the rear. The lugs can be then melted…
I designed this to fit on one of the straps of my Camelback, it made it realy easy to find when I needed it. PETG or PLA 20mm layer Height
This is based on the Karma ring but with some important changes: Flipped the nut mount point - makes access much better when wearing chest plate Thicker mounts. 2 Extra grip pads. Longer mounting arm. Vertical support ring. Cutout to…
I was really disappointed with the Spektrum DX8 Monitor mounts I have found, so I decided to design my own. I have designed this primarily for use with the Flysight Black Pearl monitor but it should fit most others. I have also designed a…
MK3S+ Style X-Motor end with new belt tensioner for MK2.5 printers that use the microswitch Print instructions print as per any Prusa Printers part
Intended to fit the WaveShare CM4 IO board with Raspberry Pi 4 Compute Module, a redesign to allow for access to the GPIO connector. The case has a 40mm fan design to blow air across the top then around the side and to the bottom to cool…
print upright with support on build plate only, I would suggest 20% infill and PETG. The Led rear light is found as an addition to many front lights being sold on Amazon at the moment. I designed a front mount for the main light and wasnt…
I was really disappointed with the Futaba T8J Monitor mounts I have found so far, so I decided to design my own. I have designed this primarily for use with the Flysight Black Pearl monitor but I will be modifying this design in the…
Overview NOTE This is V1, See V2 for the redesign ! I was really disappointed with the Futaba T8J Monitor mounts I have found so far, so I decided to design my own. I have designed this primarily for use with the Flysight Black Pearl…
Quickly made this to replace the broken strap on my watch, printed using flexible filament. Update 22/9/18 I have added the other parts of the strap but these have not been test printed. Print instructions Category: Sport & Outdoors…
I printed on PLA at 0.2 layer height 100%. Mainly as the White PLA I had was somewhat transparent and I wanted to get good solid colours. for A4S !
Just for fun 3D Benchy sliced in the middle. print in 2 colors, black for the base and red for the body.
Experimental mount for GoPro and also base Futaba mount Print instructions Experimental - Not yet printed. Suggest 0.2 PETG 30%
I remixed the origonal to better fit where you are using the PC4- M10 front plate https://www.printables.com/model/551600-mmu3-selector-pc4-m10-front-plate this also has a seperate pointer that can be printed in a contrasting color.
I printed this in Prusament PETG at 100% infill using the textured plate. I have also included the original version I designed without the speaker.
Bike mount for Victoper LED Bike lights found on Amazon. The original mount was terrible and causes the light to flop around on the handlebar. I designed this mount to fit my Cube Stereo 160 and place the light in front of the bar. There…
M16 bolt with 3 sided head commonly used in camping equipment. I would suggest using PLA / PETG with 0.2mm layers, 4 perimeters and a high level of infill.
The light rings are quite cheap and just need a 24V feed which I took from the power connectors on the Rambo board. I have mounted mine in the middle under my MMU3 and this gives good illumination to view the printer from Octoprint. I…
Bike handlebar mount to fit the cheap Go Outdoors Eurohike 1W hardtorch. This should fit handlebars around 32 mm. Feed the tiewraps from the bracket trough the mount plate and back. Click the plate in to the back of the head torch. I…
A part that joins the frame sections of a dring rack. The frame rods are approximately 6mm diameter. I printed in PLA but other matrials may suit, even a stiff flex material might work. Print with the top down, basically legs pointing up.
Bracket to hold the upholstry brush and hose on a W86-DD-B carpet cleaner. Will reguire 2 X M3 bolts and nuts.
These are all currently available results.
