Counting matching models…
GOAL : Mount a display (phone in this case) below the monitor in my home office. This display shows my agenda, provides controls for lights, AC and shows temperature/time. In the (near) future it will provide more controls and info.…
Print approx. €1.30–€1.59 excl. taxPreliminary estimate for one variant
Based on the great model by @ KaliM. UPDATED VERSION v3 on December 1st 2024. Changes : Walls are thicker (3 layers) Vertical hole at the front is bigger: easier to guide tablets going in Hole to retrieve tablets is bigger (vertically &…
Print approx. €4.43–€5.41 excl. taxPreliminary estimate for one variant
This is a remix with the following changes: - removed text and shapes to make it easier to clean Not every car uses fabrics that can be used with velcro. I have tested it with a 2022 Tesla Model Y and that works fantastic. As you can see…
Print approx. €3.43–€4.20 excl. taxPreliminary estimate for PETGSource material: PET
Great for : tissues, phone, remote, nasal spray, small book, keys, small trees and melons. Print parameters Printer : Prusa Mini+, FW 6.1 Material : PLA Nozzle : 0.4mm Layer-height/profile : 0.2 mm speed Supports : none Input shaper :…
Print approx. €10.48–€12.81 excl. taxPreliminary estimate for one variant
You can buy a stand for the Osmo Mobile 3 for around €20 or you can print it in 2 hours :-) It works great. Note that this is a re-upload of a model that I could not find on Printables but as it works so well it should also be here! :-)
This model holds your Ikea Tradfri switch in place. First I created 1 model with an angular exterior (which in my case holds the switch even better). For other folks I also created ones with a flat top. Tradfri-swtich-holder 7 mm height…
The original could not be printed on the Prusa Mini because of its max print size: 180x180x180mm. So here's the adjusted version. I have printed it in PETG and not in PLA because of temperatures in the car in the summer. The car however…
Main goal : make the drawer printable on an 18x18x18cm printer like the Prusa Mini. It has some improvements over the original model (see differences section). The left and right rails are different so you need to print them both as in…
Updated the case to have enough space for the USB cable some soldering wire and possibly a small tool. This gives you 1 box with all you need to do basic soldering. The LID file is the same as the original. Print parameters Printer :…
Dishwashing brush holder. This holder perfectly fits on the kitchen wall or on the inside/outside of a cabinet door. It can hold 2 (Ikea) brushes. v3 - original v4 - original + smoother edges and stronger v4 smaller - like v4 but for 1…
This adds a Hex key holder to the (great) display back cover. Now your Hex key is always close to your printer. Want to add the Hex key holder to other (back cover) models? Look at the “part 1/2/3” files. “Part 3” is a ready to use hex…
This adds a Hex key holder to the (great) display back cover. Now your Hex key is always close to your printer. This version is compatible with the original screws of the display! Want to add the Hex key holder to other (back cover)…
Just a lovely wallet for 3 cards. It is quite tight but I hardly ever have to take them out as everything is done by the phone. I added 2 “ribs” on the back to make it stronger plus a hole to make it easier to slide them out. The first…
I published 4 sizes 3mm (I used this but should have used a thicker one) 4mm 5mm 6mm Of course you can take any of these models and resize them in your slicer.
Sprinkle / Hagelslag challenge Many sprinkle cartons leave behind small powdery dust - IN YOUR CLOSET. And that's where it should not be so I designed an easy-to-print, easy-to-use 2-sizes tested with 5 different brands. They all seem to…
These are all currently available results.
