Counting matching models…
Let's face it. Everyone has had a bad night where the dice just don't roll your way. And we all know who's to blame. It's the dice!!! When your dice are being really bad, teach them a lesson and put them in jail! Print Settings Printer…
This piece links up to existing Lego tracks. To secure this piece to existing track, I used 1x2 plates on either side of the railroad ties.
This is a revision of a nice DM Screen. The only changes I needed to make were to resize to use some existing 8x10 chipboard. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: .2 Infill: 100…
Borrowed the wings from https://www.thingiverse.com/thing:375110 . All other parts were designed in TinkerCAD. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: .2 Infill: 15 Filament:…
I like to mount different accessories to my printer like my Octopi, Buck Converter Cases, Tool Holders. With these rails, you can reuse all of those cases and mount them to anything you can screw into.
A set of risers. ranging from 0mm to 50mm in height. These can be used to create an overpass or to create a smooth supported incline. The models are also designed to work with Bachmann EZ Track. Printing The bases do not require supports…
This combines a bed handle with the bed level knob locks. Bed Locks are labeled for easier install... LF = Left Front RF = Right Front LR = Left Rear RR = Right Rear Tested on Ender 3v2 but might work for Ender3/3Pro and possibly CR…
This model is an N-Scaled model train girder bridge designed to fit Bachmann EZ Track. This model comes in 3 sizes (200mm, 150mm and 100mm). Assembly Print Part. Attach to track. Slide EZ Track into bridge, the fit should be snug while…
Similar to Watto's chance cube, 3 sides show Rebel insignia and 3 show the Empire insignia. Dimensions are 25mmx25mmx25mm with rounded edges. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .12…
This model is an N-Scaled model train truss bridge designed to fit Bachmann EZ Track. This model comes in 3 sizes (200mm, 150mm and 100mm). All part should be grouped by their size in the filename. Therefore base_100mm goes along with…
I designed this model to hold my brushes while drying or painting to allow the brushes with the tip side down. I printed the base, pillars and snap peg in PLA, while printing the Upper/Lower Rings in TPU. The Snap Peg is optional to be…
Check out the latest version at the links below... This design has been broken into 2 separate things. DecoderToken - https://www.thingiverse.com/thing:5261467 DecoderRing - https://www.thingiverse.com/thing:5261464 There are 2 versions…
Remixed the original create a hollow compartment in the bolt to store a secret message. Also separated the Decoder Ring and Decoder Token into individual things. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No…
Remixed the original to increase the inner ring diameter and strength. Also separated the Decoder Ring and Decoder Token into individual things. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No…
This Tool Holder is designed to hold 1 Spatula, 1 pair of Snips, and 2 Brushes (purchased from Harbor Freight). To attach to printer... Feed M3*8 bolts from front face through back offset mount. (You may need to screw the bolt through the…
Small Parts Container with wiring slots for V-Slot 2020/4040 mount. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: Hatchbox PLA Black / Gold Silk Notes: I used this to…
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner…
These are all currently available results.
