Counting matching models…
This rests on the inside of a car door and holds a portable two way radio next to the side window. The belt clip on the radio holds the radio in place. This holds the radio very near the window, where the radio should perform much better…
This screws to a 100mm x 100mm VESA mount on the back of an LCD Monitor to hold a HP Elitedesk G3 desktop computer. 4x screws are required to attach the bracket to the back of a monitor: M4x10mm. M4x12mm should work as well.
I designed this battery case to fit the Yaesu VX8DR ham radio. It also fits the FT1dr, FT2dr, FT3dr, and FT-5dr. It takes 18650 Li-ion cells. I will link to some of the parts I used below. This is designed to use unprotected cells. The…
This is to manage cabling that runs up the side of a 19" rack. This attaches to the rack using rack screws that hold the device to the rack. This is 1U high.
This is a simple wallet that I made in TinkerCad. It's designed to hold three cards on either side. Or cards and cash. Use a length of 1.75mm filament for the hinge. I used a soldering iron to melt the ends of the filament after it's…
I printed this in TPU. I created this pipe bung because I was repairing my gas fired hot water tank. There is approximately 5' of gas line between the shut off valve and my hot water tank. Last time I had it disconnected, it took a long…
The print does not require any supports. I printed with PLA for modelling, but will print with PETG for the final rev. PLA should be fine if the transceiver never leaves your shack. PETG is going to be required if you plan on leaving it…
This mounts a Reolink security camera into a corner with two vertical surfaces and one horizontal surface that meet. Includes a cavity to bundle up the cabling. I had to mount a camera in a corner that was two heavy beams that I was not…
Comically large hook for Yaesu Microphones. I needed a large hook for my particular application. Uses the same screw to attach that holds the button for the OEM mic hanger.
This is a very simple dipole for UHF frequencies. I designed it to hold 70cm elements, although I've also built it as a 1.25m antenna. I haven't tried elements for 2m band yet, I believe they would be too long. I have another design that…
This is a 3S battery pack for the QRP Labs QMX Transceiver. It holds 3x Li-ion packs I purchased from Amazon. It also includes rails to protect the front panel knobs. If I don't count the rails, the battery pack only adds 8mm to the…
The slot in the t1000e is not sufficiently large for paracord. So I made this simple loop so I could hang the t1000e from my backpack with paracord. I printed the example in the photos using PLA. I held it in the heat gun for a few…
This is a faceplate / trunnion for a Motorola XTL1500 to hold it into a 10" rack. I based this on the 10" rack that many homelabbers are using for Ubiquiti gear. I thought a 10" rack would be perfect to hold two way mobile radios. The…
This is a faceplate / trunnion for a Yaesu FTM-100D to hold it into a 10" rack. I based this on the 10" rack that many homelabbers are using for Ubiquiti gear. I thought a 10" rack would be perfect to hold two way mobile radios. This…
I made this j-pole to connect to my SDR scanner. The included STL's are for the 3d printed radome and the base. The antenna element is #10 bare copper ground wire. I purchased some 10' long SMA Male to SMA Male assemblies off amazon and…
I made this to hold cables and power strips under my desk. I used 1" drywall screws, to attach it to the privacy panel under my desk. It will hold cables, power strips, and even power supplies. It just keeps them up off the floor so I'm…
These are all currently available results.
