P
Printableseveve05
Ratcheting Capo (stronger)
Print without supports After printing you have to break-loose the hinge. Optionally you can add a softer material (electrical tape/heat shrink) to the arm and body.
- Downloads
- 941
- Likes
- 53
- Rating
- 5
All models
Counting matching models…
P
Printableseveve05
Radial/rotary engine toy (print in place)
This model can show both a radial engine (rotating crankshaft with a stationary body) and a rotary engine (stationary crankshaft with a rotating body).
- Downloads
- 743
- Likes
- 151
- Rating
- 4.75
P
Printableseveve05
Wankel rotary engine (print in place)
Print at 0.2 mm layer height.
- Downloads
- 646
- Likes
- 61
- Rating
- 4.5
P
Printableseveve05
Torture stairs
Print with 0.1mm layer height to make it easier. If you have stringing problems it's going to look messy. Good luck
- Downloads
- 492
- Likes
- 62
- Rating
- 5
P
Printableseveve05
Harmonic drive (print in place)
Only tested with PET-G, PLA might not be flexible enough. Hole for a 6mm Allen wrench. Raised model has two small sections raised 0.6mm above the rest of the model. Print in different colour for best results. This harmonic drive consists…
- Downloads
- 476
- Likes
- 107
- Rating
- 4.75
P
Printableseveve05
3 way trammel
Parts: base handle stone x 3 pin x 3 Assembly: put pins in stones put stones into their tracks put handle on pins check if everything moves freely connect handle with pins, you can use glue, I used a soldering iron set to 120 ° C (for…
- Downloads
- 258
- Likes
- 109
- Rating
- 4.75
P
Printableseveve05
Spring powered propeller launcher
Printing: (red parts - C-TECH premium line PETG, black parts - Sunlu neat winding PLA) everything printed with 2 perimeters 10% lines (rectalinear) infill spring and ratchet should be printed with PETG propeller use HIPS or ABS if you…
- Downloads
- 196
- Likes
- 54
- Rating
- 5
P
Printableseveve05
30mm shell piggy bank/storage box
Print settings: 0.4 mm width @ 0.2 mm layer height for the top and body an ( outer) brim is recommended you need to add custom supports if you are using piggy bank models without pre-made supports Versions: storage box doesn't have a slot…
- Downloads
- 187
- Likes
- 20
- Rating
- 0
P
Printableseveve05
Contrarotating mechanism
If you added a gear to the body you would create a differential. (I only realised that when my dad told me) Parts: body bottom gear top gear cage x3 inner shaft outer shaft pin x3 side gear x3 The way I designed the parts to be connected…
- Downloads
- 118
- Likes
- 63
- Rating
- 5
P
Printableseveve05
Motherboard with components
GCODE ONLY FOR MATERIAL AND PRINT TIME ESTIMATE The original idea was a toy to get a child into pc building, but in my opinion, the result also makes for a great decoration. For a better look, I recommend to print with multiple colours.…
- Downloads
- 111
- Likes
- 13
- Rating
- 0
P
Printableseveve05
DaVinci power hammer
Assembly: red pins are bits of filament, bend the ends to secure them in place (PETG is ideal as other filaments tend to snap) the knob just loosely sits on its shaft, glue it if it bothers you
- Downloads
- 58
- Likes
- 7
- Rating
- 0
These are all currently available results.