Counting matching models…
I needed an extendable/portable stick. I couldn't find one that matches my needs so here it is: A highly customizable telescope stick. The following aspects can be configured: number of segments radius, length, wall thickness inner/outer…
It improves unwinding as it improves the spool edge smoothness and stability. Simply put one on each side of the spool. No glue needed. You may want to add a clip or screw at the holes if it fits too loose.
The FreeCAD file is included to make it easier to fine tune the parameters. The original spring was way too weak to turn the propellers. I decreased the number of turns and increased the thickness and growth to make this part stronger…
I needed a matching thread for the cap of a Bosch AKE 35-19 S chainsaw. The result is this parametric threaded round cap which was designed in FreeCAD. Use the spreadsheet within the FreeCAD file to adjust the various parameters.
It is recommended to print it in the given orientation with 0.12mm layer height.
Just change the parameters in the spreadsheet within the FreeCAD file. I created this because I wanted to use countersink screws on the outside. The hole for the PC4 is not threaded but worked just like a threaded one. An already…
These clips/spacer are designed for the Snapmaker 2.0 laser bed and provide three functions: Keep the workpieces at a certain distance from the laser bed to avoid contact with residue from laser cutting. Keep the workpiece from moving…
Enclosure for a standard sized 5.25" optical drive. Change the drive depth and/or printing tolerance in the spreadsheet within the FreeCAD file to match your needs. You need to drill ~3.4mm holes at the sides for the M3x6mm screws to…
Both mounting hinges broke, therefore, I made a replacement loading ramp for the shown flat bed trailer. Printing: Layer height: 0.12mm Infill: 100% Support: yes Orientation: same as STL Material: PETG Make sure that you get a good…
The original part was lost somewhere. This is a full replacement. Printing: Layer height: 0.12mm Infill: 100% Supports: on build plate only Orientation: same as STL The one in the image was printed with transparent PolyLite PETG.
Attachment for the Dremel 3000 to aid orthogonal drilling with limited drill hole depth. Printing: Layer height: 0.2mm Infill: 15% Seam Position: Random Orientation: same as STL Printed Guide and Mount with Maertz Budget PLA Pro and Base…
A minimalistic case for the USB-TTL module HW-417, which uses FT232RL. This is widely available on AliExpress and co. The modul needs no support and assembly is done without screws or other tools. Printing: Layer height: 0.2mm Infill:…
This is designed for the Snapmaker 2.0 A350 with enclosure. The FreeCAD file is included for easy modification. Tested with initial layer height 0.3mm and general layer height 0.25mm. Used Snapmaker Luban profile "normal quality" as…
Printed with PLA+ and 0.2mm layer height in the given orientation. P.S.: I didn't get the scissors to cut paper even after sharpening it with a rasp. But thin cardboard worked.
A size matching nut is used to apply the needed force. This improves the possible tightness significantly compared to a directly cut in screw threads. Printing: Print with rafts to get a proper rounded edge or without for a smooth surface.
The original part broke at the connection to the trailer. This is a full replacement. Not really suited for an FDM printer in terms of durability but works good with an SLA printer for example. Update 2023-03-06: increased thickness at…
Most properties can be configured. Like holes for wall mounting. The locks are used to hold all pieces together. Or use glue instead. Using locks, however, has the advantage of having exchangeable name plates. Notes: Proper bed level,…
The temperature/humidity meter it is designed for is widely available and cheap. For example: https://www.ebay.com/itm/112620555830 https://www.aliexpress.com/item/1005003771979525.html https://www.amazon.com/dp/B094FMCKFR/ Printing:…
The angle helps to prevent fraction on the enclosure hole. It also lowers the force needed to pull in the filament. All parts printed without support. No additional hardware is needed for assembly. The parts just snap together. This was…
Cap for the safety bar hole of the old version of a Stokke Tripp Trapp chair. You may need to wind some tape around it for a tight fit. The holes have quite some tolerance. Printing: Layer height: 0.15mm Infill: 20% Orientation: same as STL
A case for the TTGO T4 v1.3 ESP32 development board. Only two of three buttons are available as the remaining one is also connected to an internal sensor and therefore not fully usable as user button. Furthermore, boot and reset switches…
A ruler for the Capricorn PTFE tube cutter to easily cut pieces to a specific length. The dimensions of the ruler can be adjusted in the provided FreeCAD file (spreadsheet "Param"). A 65mm example ruler is included as STL file. The actual…
Adjust the dimensions in the spreadsheet within the FreeCAD file as desired. Two different design approaches are included. Printing: Enable the ironing option for all surfaces to get a smooth and waterproof base.
A small magnetic mount for a common temperature/humidity meter. Requires: temperature/humidity meter https://www.ebay.com/itm/112620555830 https://www.amazon.com/dp/B094FMCKFR/ 4x ⌀4x2mm or 2x ⌀4x4mm neodymium magnets…
The hitch broke in the middle of part that extends to the axis and at the sides at the ejector pin marks. Glue alone does not last long, therefore, I made a splint to keep the parts together. Printing: Layer height: 0.2mm Infill: 100%…
The included FreeCAD file can be easily adjusted to match the desired size and parameters for printing. Layer adhesion is important to avoid the stick from breaking off. Cut off the bristle support pipe with a little knife after printing.…
This is a replacement ramp for Majorette station. Printing: Layer height: 0.08mm Infill: 15% Orientation: thick end to build plate Support: recommended Print with Cura tree support with the thick end facing down or in the giving…
I have printed this model up-side-down (i.e. in the given orientation) with the following settings: 0.2mm layer height 0.45mm line width (0.4mm nozzle) 110% flow rate vase mode 1mm bottom layer This took 6.5h at 40mm/s. Vibrations started…
The quick mounting clip of my curtain rail broke (see picture). This was made to replace the broken part. Use at your own risk: I recommend to replace this with the original part as soon as possible. Printing: Layer height: 0.12mm Infill:…
This TAN USB PWR adapter allows the modification of the KOBIL "TAN Optimus comfort" to power it directly from USB instead of using batteries. Perform the steps described here to build such an adapter. Please note that soldering is…
These are all currently available results.
