Counting matching models…
My wife started hanging grocery bags on the kitchen cabinet door. I decided I could do better than the door handle and designed a couple of brackets that fit the door and sort of held the bag open. Not being completely satisfied with how…
Needed cable clips for my Next Level Racing GTELITE. Found one I liked but it didn't fit my 4040 profile, so I made my own from scratch, copying the same basic shape.
Made hooks wider and deeper for better retention. MOved mounting tabs inboard and resized mounting holes for M3 screws. Installed with 4040 M3 T-Nut by Olafelch - https://www.printables.com/model/217606-4040-m3-t-nut. Printed with organic…
These were sized using Safariland Comp III speed loaders for K frame and L frame revolvers. Also works for Ruger GP100, which is the same geometry as an S&W L frame. Printed in Elegoo PLA. 15% infil, adaptive cubic, three perimeters. Not…
Edited: Use the new (much better) version here: https://www.printables.com/model/653554-ender-3-v3-se-c270-camera-mount A Logitech camera mount for the Ender 3 V3 SE. Glue the two dovetailed parts together with CA glue. Mounts to the 2020…
Mounting bracket for Sabrent 10 port USB hub. Mounts with a screw at each end. This is not and was not intended to be rigid enough for you to yank cables out of the hub, just sufficient to hold it vertically on my sim rig. Printed in…
Simple press together mount to add a light to Lee Six Pack Pro reloading press. Retaining ring just snaps onto the base. Easiest way to do this is to place retaining ring on flat surface and press the mount down onto it. Retaining ring…
Shift gates to be placed over the standard 8 position shift gate. Extrusions on the back help to keep in place. These are sized tight for my shifter, requiring some sort of tool to start prying them off. Printed in PLA or PLA+, 15%…
Picatinny rail for a vintage 1965 Crosman 760 Pumpmaster. Mounts to the barrel using the iron sight screws as well as clamping to the barrel using M3x16mm machine screws. Printed with Elegoo PLA, brim, 90% infill. Chased through holes…
Simple foot rest. Printed PLA, 3 shells, 15% grid infill. Organic supports on the large holes. Print support on it's side, pedal flat. M8 screws and T-nuts to mount to extrusion. Two M3x20 screws to attach the pedal. 2026.04.20 Added…
The Quest 2's habit of sliding down my face whilst sim racing because it's unbalanced was driving me nuts, so I made these. Counterweights for KIWI design Comfort Head Strap for the Quest 2. Designed to snap onto the back on either side…
Mounting brackets to attach a Fanatec CSL DD 8 newton-meter power supply to 4080 aluminum extrusion. Used M6-16 screws and printed T-nuts available here: https://www.printables.com/model/922383-updated-sabrent-10-port-usb-hub-mounts
As I often switch between cars using sequential and h-pattern shifters, I grew tired of how long it took to remove a shift knob and then screw another one on, so I created an interrupted thread version that goes on and off with ¼ turn.…
Hang a Logitech K400 PLUS keyboard mount under Next Level Racing GTELITE wheel deck. Uses M4 x 16 mm screws threaded into printed “nuts”, which fit in the 8mm x 60mm slots in the wheel deck.
2026.03.26 I've reworked this a bit. The straight dovetail mount loosened over time due to PLA creep (aka plastic deformation), so the latest version uses tapered dovetails. As it loosens it just sits a tiny bit lower in the mount. Also…
I decided I didn't like the feel of the original paddle shifters on the WRC wheel so I duplicated the outline of the original, but thicker with more rounded edges. Fit is the same as the originals, but needs slightly longer screws.
Underwear works well to manage all the USB and power connectors on my sim racing rig.
A counterweight to balance an Oculus 3 with the KIWI design K4 head strap. Printed in PLA, 3 walls, 15% infil. Top and bottom attached with M3x12 countersunk screws. Added lead to make the total weight 285g, which feels about right to me.…
Threw together a Wyoming Satellite using the Slacker Labs tutorial . It works just fine, but the components do not fit in case he referenced, so I designed my own. The Pi screws into the base with M2.5 screws. The hat is just supported by…
Note: after using it a while I decided it needed a bit more resistance when shifting and just stuck another magnet on the magnets in the cups. Flash the Arduino following the instructions provided by SimHub. SimHub Arduino setup -…
A simple case for Raspberry Pi4, SSD and Homerun Adapter. Consists of the main case, a side panel, and an adapter to connect Pi4 and SSD. Pi4/SSD combo connected to case via the SSD's side mounting inserts. All hardware except M2.5 screws…
This is a simple stand which allows the rollers to be used in place rather than rolled on the floor (my wife's preferred use). Print the base, two of the uprights, and the bar. No glue required. Just slide the uprights into the dovetails…
A 4080 hanger for the Oculus 3 with Kiwi Design head strap and my counterweight attached. This will likely not work well without the counterweight on the strap as it moves the CG to just behind the swivel points. The arm is attached to…
If you have arthritis in your hands those new stubby little plastic-saving short caps they put on milk / half&half / etc. are painful to remove. This makes it easy to break them loose. I've saved several of the old-style tall caps and…
I replaced my plastic pour-over with a Melitta porcelain pour-over. I'd been using a small bowl to catch the last few drops but the new pour-over was very unstable on it, so I designed and printed one that uses a small jam jar to catch…
These are all currently available results.
