Counting matching models…
This cover/cap is for the Makita 18V X2 (36V) LXT Brushless 6-1/2” Plunge Circular Saw, model XPS01. The cover is very precise. It will keep dust from escaping through the side opening, thus improving dust collection. Be sure to check out…
I use these clips currently to keep the wires around my desk from getting caught under my desk chair wheels. The clips self-lock when closed. Print them on their side, no supports. I recommend printing them with several walls so there is…
I realize that there are several other version of these guide rail end caps. This is my own version that I quite like. These were designed with the Makita guide rail specs and should work with Festool and Powertec guide rails, possibly…
I think I've worked out a pretty decent solution for a track saw guide rail rack that doesn't require any additional hardware. Every piece is printable with little or no supports. The only piece that I print with supports is the primary…
A simple modular tool organizer for any toolbox. Dividers clip onto 1/4" steel rods (or something similar). The design includes blank dividers and interchangeable labeled dividers. The labels and clip are designed to be printed on a…
My wife wanted to be able to customize our drawers in the kitchen. She found some ideas on Pinterest, but I decided to make a system for all of our drawers. We purchased some poplar planks (1/4" x 2 1/2" x 48") and cut them to the various…
Simple ergonomic knobs for M5 or M6 bolts/nuts.
I was in need of a scribing tool on the last set of shelves, so I made this one before I finish the next set going in. This simple scribing tool has two ends to help scribe various surfaces: The ball bearing end is made for flatter, less…
This is a series of clamp pads for the Microjig MATCHFIT dovetail clamps. The green rendered pads are for the swivel end of the clamp. The blue rendered pads are designed for the dovetail end of the clamp. Simply invert the clamp and use…
Simple, minimalist Makita 18V LXT tool mount. There is a slight downward slope to the back of the holder to allow gravity to help hold the tool snug. Print standing up with no supports.
Simple, minimalistic battery mount for the Makita 18vVLXT batteries. Batteries can be inserted from either side and the battery locks in place. Print flat, with supports.
Dovetail track pieces that can be used either with an M5 bolt or an M5 nut. These work well with MatchFit workbenches. I've included three sizes: 40mm, 50mm, 100mm Print with the narrow side down, no supports.
Simple, minimalist mount for Porter Cable batteries. Print standing up, no supports.
Another featherboard for you to consider. I designed these years ago and have been using them ever since on my table saw, band saw, and router table. There are several different sizes to choose from to fit your needs. I use them with my…
This is a center finder and edge marker. Most standard pencils should fit. Squeeze the sides to hold the pencil in place while marking the center line. Flip the center finder over and use the markings to measure and mark 1/2, 3/8, 1/4,…
This spool holder is made to go on the outside of a Flashforge Adventurer 3. This allows you to use third party spools of filament. You will need two 608 ball bearings for the roller to complete this build. Print the spool holder parts.…
I'm always losing or destroying the clamp pads for my collection of Harbor Freight Quick Release Bar Clamps. Fortunately all of the various sizes use the same size clamp pads. These clamp pads are a little heftier than the originals, but…
I made this for a handful of loose router bits that I have. They are all 1/4" shanks. This caddy uses two pegs to connect to a standard pegboard. The pegs fit fairly snug into the back of the caddy but I still used some super glue to be…
I needed a quick offset t-nut for the Ender 2 Pro. It uses an M3 nut.
Miter/mitre inserts - one style for flat head bolts and the other for standard hex bolts. 18.7mm x 76.2mm / .75in x 3in
Simple bandsaw inserts for the Ridgid BS14002.
Here is an easy to print cookie cutter to divide up your favorite big cookie into four pieces for sharing or for easier eating.
This is a custom t-slot track. It will be used on a crosscut sled for my table saw (will post photos soon). I can print 3' of this for a few dollars vs $30+ for an aluminum track. The tracks print around 6" and have two tapped screw…
This is one of those few designs that worked the first time. I needed a custom swtich box to fit the new safety switch I installed on an old Duro table saw (as seen in the pictures). The box is 73mm deep. I've included the STEP file if…
I found a great idea from a teacher in California named John Umekubo on Twitter. This is a remix of his original. You can find his version and other designs here on Thingiverse. It is a simple setup to turn any laptop or iPad front camera…
These are all currently available results.
