Counting matching models…
This is a remix of ElementalFocus's ( http://www.thingiverse.com/thing:3421594 ) clamp cover. I resized it or scaled it down to fit the small size trigger clamps. The test piece is used to verify the slot opening on the clamp mechanism.…
Battery Cap Dust Cover. This is specifically for the VELOTRIC Discovery 2 e-bike battery compartment to keep dirt and du
Replaces carpet clip on many GM cars and SUV's
For those with sensitive skin these finger grips will isolate the heat from the bet plate. This is specifically for the Sovol S06. But can be adjusted for other PEI plates by increasing the width and height. Print Settings Printer: Sovol…
If you use those Sterlite 32 quart / 32-liter airtight totes, you know the handles readily break off. The little nub breaks. This solves that problem. Use a 13/64 drill and be sure to drill the hole centered of the broken one.
Operate two seperate light switches with one lever. I have a bathroom with a two gang switch plate. One swicth is for the light. The adjoing one is for the fan. Family member don't seem to undersatnd that when using the shower/tub or the…
The lever for the clutch release on the Cub Cadet and MTD snow throwers to allow freewheeling will sometimes get hit and break. Though not very expensive to replace, this is a 3D printed version that is an almost exact duplicated.
Those cheap hot melt glue guns don't have a very good base to stand on. So I decided make one. Print instructions Category: Hand Tools
Print Settings Printer: Crane M3D Rafts: No Supports: Yes Resolution: high Infill: high Filament brand: any Filament color: any Filament material: ABS Notes: I use this to fill with moth balls then insert it into a plastic bag lined…
This is a replacement lid for the RIVAL slower cooker. Will most likely fit most brands. You should use stainless steel nuts, bolt and washer. Updated the slow cooker handle replacement. Nothing like actual field testing. Wife says the…
Edit 4-1-2024: Added a style without the internal structure. That allows for better washing during the dishwasher cycle and uses less filament and quicker print time. If you use those DIY KEURIG K-cups, then you know how annoying it is to…
This a mounting block for an endoscope (8mm) and protective cap. The mounting block can be glued to various arms or mounts as fits the situation. This thing was made with Tinkercad. Edit it online…
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/k7m7u7Cp5zT Print instructions Category: Audio
Universal rear bike light clamp for carrier rack. Does your rear bike storage pack block your light attached to the seat down post? This clamp is sized to attach to the rear carrier frame. It can be positioned in horizontal or vertical…
This is very specific to the FARO UNIT 1 bike helmet turn signal module that attaches to the handlebar. Make switching the module from bike to bike very easy. Use zip ties to mount to handlebars.
Best to use TPU. But it's kind of tricky to print with. If using any other material, I suggest you clip off the male peg or keep it very short so as not to break it off inside your connector.
A safe place to store those nozzle cleaner needles. Two dia. sizes depending how well you printer can print a small hole. 1.5mm or 1.69mm Print in the vertical position and use a brim to ensure bed adhesion.
Summary Replacement male clip for the GORILLA dog slip-resistant car seat protector. Gorilla would not replace the clip, so I made my own. Use PLA+ or better still PET-G
Used Tinkercad Pet-G for extra strength
This is a work in progress. The plastic is not as good as the original metal cleats. I plane on making a design that can take a metal insert such as a dull nail. Use concentric supports at 10% and .2 separation. use a brim Print in ABS or…
03-18-2024 Added version 6.1. Although the previous version is slick because the leash slips into the holder, I decided to eliminate the leash slot and just use zip ties to lash the leash to the holder. This has several advantages. First…
Nothing is more inconvenient than holding a poo bag and walking the dog. Especially if you walk two dogs or your dog does multiple jobs in one walk. This was to be a single print, but it became too complicated with supports, so I divided…
A safe place to store those nozzle cleaner needles. 2 dia. sizes depending how well you printer can print a small hole. 1.5mm or 1.69mm Print in the vertical position and use a brim to ensure bed adhesion.
Recharge stand for Philips Norelco Shaver Model 2600 series Shaver came without a charger stand. I was too cheap to buy the one with a stand. I made one. Now all I do is place it in the stand and walk away while it recharges for the next…
Replacement clip for Energizer Head lamp I broke the head band clip on this headlight, I liked the headlight so much that I decided to make a new clip. Used Pet-G for strength. 95% infill. Used support but not necessary to remove support…
This is specific for the Velotric D1 Plus e-bike. It’s to cover the battery terminals on the bike when the battery is not installed. Should be used when transporting bike by car or for storage when bike is not in use. There are two…
These are all currently available results.
