Counting matching models…
I changed the model to accommodate more batteries, added reinforcements on the sides and the battery logo on the top. Printer settings: 0,2mm layer height 4 shells no support for box, recommended for lid with logo Added new revision V2…
Stand for 30 milling cutters, diamond burs, polishing rubbers and many others. Holes adapted to a diameter of 2.35mm, 15 degrees of inclination. You can glue rubber feet for better stabilization.
Two feet to raise the XBOX Series X console horizontal by about 17,5mm. Easy to print and lightweight. Rubber feet as always are optional to use.
Standard case without feet for JBL Charge 5 and with side protection and reinforcements. Screws needed for assembly: 6xM4 8xM3 with nuts (use glue to hold nuts in right place) Print options: Print with PLA or PetG with layer height 0.2mm…
A simple adapter for quick installation of the original Karcher WD3 vacuum cleaner hose. The connection of the elements is loose enough that insulating tape could be used to seal it. Printer settings: 0,2mm layer height 4 shells use tree…
Round styrofoam cutter - 67mm of diameter. Connect with two M8 nuts and sharpened threaded rod.
It's very difficult to find a good phone holder for my car, which is a KIA Ceed GT. The standard phone shelf is not comfortable at all. In my previous car, I always had the phone in front of my eyes. Here it's hard to mount the phone to…
...to atach speakers straight to the wall.
Cable management for HSW for placing the cable at the top or bottom of the HSW.
A simple remix of two existing printables projects. Created for cleaning car air conditioning. Used hose comes from a water treatment system and has an external cross-section of 1/4 inch / 6,4mm. Remixed models were enlarged and adapted…
It's a remix of two great models into one even better Print vertically and use brim for better adhesion. For a better look, draw a seam inside the model in Orca slicer. I printed mine in PLA.
I designed a monitor light bar for my desk. It's my first design so I am not an expert but all parts fit close to perfect. Cable chain and nuts are not my projects so I refer to the pages:…
Those hooks fits a 16L Curver box - 39x30x21 cm, but they may probably fit others. The top height of the edge of the box is important. Each hook is attached to surface by 4 screws.
Wheel bolt cover 21mm for KIA CEED (in my case GT version), PROCEED and others. I suggest printing one model to check the fit, there are 2 versions to choose from - normal and tight. Print with ABS or ASA - prefered.
Wallmount for LiitoKala Lii-500 charger, compatible with HSW
Cooling system with 3 x 60x15 mm fans and W1209 thermostat with sensor. It allows you to reduce the inverter temperature by approximately 10 degrees Celsius. Mounted with 2 screws to the wall, does not interfere with the existing…
A slightly modified model to suit my needs. I added slots for SD cards with a reader, USB A and USB C pendrives, an OBD2 diagnostic tester that I sometimes use, USB cable and 2 pen holders to prevent noise while driving. I left 3 coin…
An M14 threaded rod is used as the basic handle, it is strong enough to hold a bucket full of water. I printed it in PLA but I recommend PetG or something more durable.
Remove the OBDII socket from the housing and insert it at a 90-degree angle using an adapter. Now you can close the fuse cover and have the scanner permanently installed. Use supports and 0,2 mm layer height.
It's a 3D scan of the original part of the vacuum cleaner handle. I used an Anycubic Basic grey resin and DLP printer. Fits like the original part, two elements are required.
Simple remix for Unitak3D Direct Drive conversion for better cable management
These are all currently available results.
