Counting matching models…
This is a Sighting-in rifle rest that I made for my Savage Model 64 22LR caliber. The fore-stock sits in the yoke very nicely. The drawing PDF file has the assembly details. The feet I used in the pictures were re-used from an old clothes…
Here are some 22LR storage boxes and trays. These are designed to be able to arrange large amounts of bulk 22LR ammo into either a 50Cal or 30Cal standard ammo boxes. I designed one model so that three boxes and 15 trays can be stored in…
At 1:1 scale makes a figure about 6" (15cm) tall. Joint tolerance should allow to snap parts together and have a slight friction.
A set of simple but strong shelf brace mounts. Suggested size use: 75mm: 4" boards (3.5" finished or 89mm) 110mm: 120mm boards 125mm: 6" boards (5.25" finished or 133mm) 180mm: 8" boards (7.25" finished or 184mm) Note: Picture is of…
My wife wanted something to keep cell phones from just laying on our kitchen counter while they were charging. This wall unit is what I came up with. This unit is compact and is capable of holding 3 phones at once. The slot trough the…
Yet another ANL fuse holder. This one has a smaller foot print ;) (excuse to punt) because the mount hole are under the actual fuse body. The detailed parts list is included as a PDF file. IMPORTANT NOTE: the exposed ring terminals must…
Here are some 9mm x 19mm Parabellum storage boxes and trays. These are designed to be able to arrange large amounts of bulk 9mm ammo into either a 50Cal or 30Cal standard ammo boxes. I designed one model so that three boxes and 12 trays…
This is a small gravity feeder I made for our Guinea Pig cage. The cage we have is the one from Living World as seen in the picture. The cage has tapered walls for it's base tub which this design accommodates for. The picture in the cage…
Use 3mm screws to assemble side plate to base. Holds 48 AA batteries easily. This was my first attempt at designing a dispenser of this type. I have adjusted a few things in this version from the original prototype I printed. In all it…
I needed a dispenser for chlorine tablets for my pool. the one that came with my pool used only 1 inch pucks, and those were to small and were more expensive (as I was using 3 or 4 pucks every 2 days and could only buy smaller quantities…
Just be aware that in order to use the XH-M229 breakout board in this enclosure if will require some de-soldering and re-soldering of the switch and power indicator diode in order to mirror the mounting of the board. However, this then…
Here are some 5.56mmx45mm NATO (or 223 Remington)storage boxes and trays. These are designed to be able to arrange large amounts of bulk 5.56mmx45mm NATO ammo into either a 50Cal or 30Cal standard ammo boxes. I designed one model so that…
As requested here is a AAA version of my AA Battery Dispenser. This should hold over 48 AAA with ease. I haven't had a chance to print this one yet, but based on the lessons learned from my AA dispenser prototype, this AAA dispenser…
Knob for slide potentiometer 1x4mm tang used on DJ and audio mixers. Picture is of the ones on my controller and have my logo embossed into them, but the model included does not (keeps them universal for every one to use). Enjoy!
This is a small box I made to house my XL4015 DC-DC Buck Converter. This enables me to plug-in any DC power supply up to 32V and then step down the output to any voltage from 0.8V to 30V DC. This unit can have its maximum output current…
Part Cooling Fan Duct upgrade for the TronXY P802MA printer Category: 3D Printer Parts
This will fit a 3/8 inch plastic water line. The same type used for refrigerators and dishwashers. The inner diameter is 0.371 inch, this allows for a snug fit and no glue is required. You could always scale the part from the base…
Great way to mount and incorporate a universal inline water filter to your appliances. Enjoy!
Simple 92mm to 80mm computer fan mount adapter. This adapter as a as a 20mm height with a cowling to direct airflow. Version 1 has 2.5mm diameter screw holes, and version 2 has 3.5mm diameter screw mounting holes.
Here are some 7.62mmx51mm NATO (or 308 Winchester) storage boxes and trays. These are designed to be able to arrange large amounts of bulk 7.62x51mm NATO ammo into either a 50Cal or 30Cal standard ammo boxes. I designed one model so that…
These are based in my 50Cal and 30Cal Ammo can boxes and tray organizer system.
Here are some 45 AUTO (ACP) storage boxes and trays. These are designed to be able to arrange large amounts of bulk ammo into either a 50Cal, 30Cal, or PA108 standard ammo boxes. I designed one model so that three boxes can fit either the…
The grommet from the umbrella hole in my patio glass table top was broken, so I printed a simple replacement. This bushing will accommodate a 2" hole in the table top, and an umbrella pole of 1.5" diameter. Category: Outdoor & Garden
Wanted to share the display stand I designed for my FAB 365 Star Destroyer ( https://fab365.net/items/505#inform ). This stand works with a model that was printed at a scale of 1:1 for the FAB365 files, if you changed the model scale for…
I had to mount 3 fuse holders for a project, I found it difficult to cut and drill the precise rectangular holes with the small screw holes right beside each other. During the cutting of my first rectangular hole my panel cracked. The…
Here are some 44 Magnum storage boxes and trays. These are designed to be able to arrange large amounts of bulk 44 Magnum ammo into either a 50Cal or 30Cal standard ammo boxes. I designed one model so that three boxes and 12 trays can be…
Needed a plate to mount multiple rocker swtiches to a North American electrical box, this is what I came up with. here is a link to the same style of rocker switch I used (model KCD3-102N):…
I made two sizes. As I realized that the 185mm x 185mm would fit better on my printer.
Use this simple adapter to mount a 2.5in Solid Sate (or old laptop disk) drive into a 3.5in drive bay.
This version is in-line and therefore as no requirements for a jack at all. Category: Electronics
Needed a plate to mount Europeen style power socket to a North American electrical box, this is what I came up with. here is a link to the same style of power outlet I used:…
Mount Plate for 2 MOSFET RAMPS for TronXY P802 series REPRAP 3D printer. For use with MOSFET Mounting holes 62.8mm x 37.8mm apart for 3mm screw Link to MOSFET board on ebay:…
Vertical frame brace for the P802 series 3d printer from TronXY. Made to fit on the Right-hand side of the printer. Category: 3D Printer Parts
12VDC SRD Relay PCB & 3D Printed Case Project This project is a compact and reliable 12VDC relay control module designed for general-purpose switching applications. It includes both the custom PCB design files and a matching 3D printable…
These are all currently available results.
