Counting matching models…
I made some changes to the original Design: Added Ender 3 version of Y-Axis tensioner Uses M4 screws and insert instead of M5 Made the bearing holders slide into their housings easier Extended the length of the bearing holders so the…
Remixed version of the original, 2 cm higher to accommodate more space for silica gel pearls at the bottom of the box. Watch my video about the new version here: As a cheap dry storage box for filament, IKEA Samla boxes (57x39x28 cm) are…
IKEA Skadis compliant wall panel with 6x6, 5x5, 4x4 holes and other sizes. The standoffs are 25mm. The front will be 30mm from the wall. Mounted with 4x screws, ideall sunken head. Print with 10% gyroid infill, 3 top, 3 bottom layers, 3…
This version is fixed to the Ender 3 v2 X-Carriage using the two upper roller wheel screws instead of the BLTouch mounting holes. Remixed from: Biqu H2 Mount + Cover - Ender 3 CR10 https://www.thingiverse.com/thing:4740250 BIQU H2 Ender 5…
Print with 3 perimeters for stability Use 4x M3 Threaded inserts, outer diameter 5mm, length 4mm: https://s.click.aliexpress.com/e/_DmG9Lyz
Updates: 2023-03-25 Added Top Grill with flat surface (no power button cutout) Added Body with smaller cutout for flat IO panel mainboards (note: this only works for mainboards that have no protruding border around their IO panel. 99% of…
I remixed the fanconnector as it was too small for my WinSinn 5015 fan and my part cracked upon insertion of the fan.
Replacement part (Pillar) 30225762 for Playmobil 5568 This part is not available from Playmobil anymore. Can be printed with PLA but I recommend PETG or ABS/ASA for more stability. Print in 0.2mm or thinner layers. Prints with no supports…
A quick remix to fit the BTT PI V1.2 case to the VESA 750 pi mount backpack from Justin Vallely: https://www.printables.com/model/431027-sovol-sv06-backpack
These 100mm or 200mm protruding arms will hold your tube lights nicely on an IKEA Skadis wall panel. Print them in PLA with 3 perimeters, 3 bottom and 3 top layers, 15% gyroid infill There is a 100 mm and a 200mm version available. The…
This version has been tweaked so the belt insertion slots are 0.2mm tighter to hold GT2 timing belts.
Print in 0.2mm layer height, 25-50% infill Print upright, no support. Brim optional. Using PETG, ASA or ABS is recommended 1-2 Screws to wall-mount.
This is a remix with more space for the new wingnuts of the Anet A8 Model 2018, also I reduced the size of the inner wheel because it collided with my frame. Don't forget the support because I added a little extrusion to distance the…
I've designed this turntable to fit on a standard 3/8" tripod mount. Used it on the Edelkrone Head One to shoot fotos for photogrammetry. Check out my YouTube Documentation about the process. Print instructions Category: Camera Print…
This is my first release of a 3D printed teleprompter with NATO rail mount. It works perfectly with phones and small tablets. I am using a Smallrig articulating 11" arm on my camera rig to hold it in front of the lens. This makes it easy…
Added some clearance in one of the racks as I found it to be too tight, even with a well tuned printer.
Modified mount for the The 100 printer front bottom frame. Print with strong infill (25%, 3 perimeters) as you have to use longer screws for going through the mount and the front connector into the frame.
Watch my end-to-end process here:
Should be cut in two pieces for printers smaller than 300mm build plate size. Prints fine on the Bambu Lab plate but still too large for 220x220 plates if cut in two pieces.
Shortened the connectors by 20mm to 156 to fit my smaller wall panels Also added a longer 236mm version but beware to not overload those Prints best with 3 perimeters and gyroid infill. Supports: optional Brim: depends on your printer, I…
These are all currently available results.
