P
Printablesdick
IKEA Skadis Board Connector, side-by-side
Exactly the same as the original model - but sideways! The sources are also on Tinkercad
- Downloads
- 418
- Likes
- 44
- Rating
- 5
All models
20 models
P
Printablesdick
Skadis T-Nut mount for Stanley Fatmax snap-off knife in 9mm
This is a mount for holding a Stanley Fatmax 9mm snap-off knife (model 0-10-475) on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need only one nut and the M2.5 hardware to attach it. I use an…
- Downloads
- 114
- Likes
- 8
- Rating
- 5
P
Printablesdick
Skadis T-Nut mount for Klein Wire Cutter and Stripper
This is a mount for holding a Klein Wire Cutter and Stripper on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need two nuts and the M2.5 hardware to attach them. I use M2.5x16 screws. No supports…
- Downloads
- 91
- Likes
- 8
- Rating
- 4.67
P
Printablesdick
RMU Mk3 mount for Original Prusa Enclosure (upper)
This is an upper mount to attach the Wedge RMU Mk3 to the right side of the Original Prusa Enclosure. It uses the tool holder model for mounting. That uses: M3x8 screw (2x) See RMU Mk3 mount for Original Prusa Enclosure (lower) (…
- Downloads
- 87
- Likes
- 11
- Rating
- 4.5
P
Printablesdick
Gridfinity holder for Ring batteries
A container for Ring batteries, in the style of Definitive Collection of Battery Holders (Gridfinity, Stackable & Labelled) by xavierly (although this one is not stackable!) It holds two batteries in a 1x2 Gridfinity container. The base…
- Downloads
- 85
- Likes
- 5
- Rating
- 5
P
Printablesdick
esp32-case with countersunk mounting screw hole
This is the Mihai esp32-case, but with a countersunk mounting screw hole added to the base. I borrowed the hole design from https://www.printables.com/model/275743-parametrised-power-strip-mount-with-rounded-corner
- Downloads
- 77
- Likes
- 7
- Rating
- 0
P
Printablesdick
RMU Mk3 mount for Original Prusa Enclosure (lower)
This is a lower mount to attach the Wedge RMU Mk3 to the right side of the Original Prusa Enclosure. It uses my Original Prusa Enclosure corner mount model ( https://www.printables.com/model/345660-original-prusa-enclosure-corner-mount/ )…
- Downloads
- 67
- Likes
- 7
- Rating
- 4.33
P
Printablesdick
Tool Holder for Original Prusa Enclosure (left side)
This is the original tool holder, but flipped to mount it on the left side of the enclosure. All I did was load the original model into TinkerCAD and click the mirror button. See the original for printer settings and mount instructions.
- Downloads
- 61
- Likes
- 10
- Rating
- 5
P
Printablesdick
Original Prusa Enclosure corner mount
This is a mount for the corner holes between two sheet metal sections of the Original Prusa Enclosure. It is not useful in its own right, but it can be incorporated into other models. I've uploaded the OpenSCAD file to make this easier.…
- Downloads
- 37
- Likes
- 6
- Rating
- 0
P
Printablesdick
Skadis T-Nut mount for soldering flux container
This is a mount for holding a container of soldering flux on the IKEA Skadis board. It's a remix of the Skadis holder for tip tinner (Thermaltronics, 20 g) by Rai but made bigger. Thanks Rai for publishing the FreeCAD file, it made it so…
- Downloads
- 35
- Likes
- 4
- Rating
- 5
P
Printablesdick
Wheels for the Prusa enclosure
This replaces the supplied feet with an adaptor to mount small wheels instead. Each corner uses: M3x12 screw (4x) to attach the wheel M3x10 screw (2x) to mount to the enclosure M3n (6x) The wheel I use is this:…
- Downloads
- 30
- Likes
- 13
- Rating
- 0
P
Printablesdick
Skadis T-Nut mount for Molex Hand Crimp Tool
This is a mount for holding a Molex Hand Crimp Tool on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need two nuts and the M2.5 hardware to attach them. I use M2.5x16 screws. No supports are…
- Downloads
- 30
- Likes
- 5
- Rating
- 0
P
Printablesdick
Skadis T-Nut mount for Asus ZenWiFi AX
This is a mount for holding an Asus ZenWifi AX on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need two nuts and the M2.5 hardware to attach them. I use M2.5x16 screws. There are also countersunk…
- Downloads
- 27
- Likes
- 2
- Rating
- 0
P
Printablesdick
RMU Mk3 base mount
This is a mount for the base of the Wedge RMU Mk3 filament buffer. It is not useful in its own right, but it can be incorporated into other models. I've uploaded the OpenSCAD file to make this easier. For mounting to the RMU base this…
- Downloads
- 24
- Likes
- 1
- Rating
- 0
P
Printablesdick
Washer for 3mm longer body and shaft
I used the 3mm longer remix ( https://www.printables.com/model/301787-3mm-longer-body-and-shaft ) of the Ratchet toothpaste tube squeezer ( https://www.printables.com/model/265248-ratchet-toothpaste-tube-squeezer ) but found a bit too…
- Downloads
- 22
- Likes
- 3
- Rating
- 5
P
Printablesdick
Skadis Secure Clip mount for the Engineer SS-02 Solder Sucker
This is a mount for holding an Engineer SS-02 Solder Sucker on the IKEA Skadis board. It also includes places to store the spare silicone tubes. It uses the IKEA Skådis Secure Clip System Template from mkingery , and a pair of the clips…
- Downloads
- 18
- Likes
- 3
- Rating
- 0
P
Printablesdick
Skadis T-Nut ring with 18mm inner diameter
This is a horizontal ring with an inner diameter of 18mm for mounting on the IKEA Skadis board. The included freecad file should be parametric enough to create any other sizes required. I use it to secure the end of a digital caliper, to…
- Downloads
- 17
- Likes
- 5
- Rating
- 0
P
Printablesdick
Utility Meter Pulse Optical Counter (Home Assistant Glow) with wall mount
This is the Utility Meter Pulse Optical Counter (Home Assistant Glow), with a few additions: A wall mount with an alignment guide The base is 2mm taller, to allow more space inside for wiring A reset pin. Accessing the pin hole is quite…
- Downloads
- 13
- Likes
- 1
- Rating
- 0
P
Printablesdick
Gridfinity stackable holder for Ikea Braunit batteries
A stackable container for Ikea Braunit batteries in the style of Definitive Collection of Battery Holders (Gridfinity, Stackable & Labelled) by xavierly It holds two batteries in a 1x2 Gridfinity container. The base OpenSCAD model is…
- Downloads
- 9
- Likes
- 3
- Rating
- 0
These are all currently available results.