Counting matching models…
Update Aug 20 2025 In response to comments about the fit of the threads I am now including renders with increased thread tolerance gap. You can also make custom adjustments to the fit by editing the value of the ThreadToleranceGap…
Fender washers in all of the sizes typically sold in assortment packs. Parametric f3d included for custom sizes. Public domain license. UPDATE 2026-05-14: Re-rendered all STLs with correct inner diameter. Previous ID was set to exact…
Parametric f3d included for making custom sizes. These spacers are designed to match the width of the screw head. Public domain license. Part of Metric Screw Spacer Mega Pack 1 - Sizes M1.6 - M12
A Duct-Extended v6 Printhead for the Stealthburner The Voron Stealthburner toolhead includes a printhead module that is compatible with a standard v6 hotend. In this mod I attempted to replicate bythorsthunder's mod for the Stealthburner…
This model is designed for 320mm or larger printers. It can be printed at a smaller size, but you may need to drill out the screw holes if they're too small. When printed at 100%, the two main sections can be assembled using 4 x brass…
A shallower remix of my Triple Shelf with Honeycomb Storage Wall Sides 220mmW x 150mmD
A remix of my Double Shelf with HSW Sides 200mm in a larger size with an added middle shelf. 320mmW x 150mmD x 316mmH.
Wall-hanging double shelf with Honeycomb Storage Wall (HSW) sides to store more things.
A clip for clothes, fabric, curtains, etc.
This is not a calibration model, it's intended for use once you already have your Pressure Advance (aka Linear Advance) tuned and you are ready to fine tune it with a more advanced challenge. The outer facets are designed to visualize…
Smaller remix of my Triple Shelf with Honeycomb Storage Wall Sides 320mmW x 150mmD
I wanted to add a pot to Hitsman's Low Poly Bulbasaur Planter because it's designed to hold a separate pot, and it doesn't hold much soil on its own. I ended up making it look like a Mario pipe, extending the pot down to the floor for…
A remix of my Clothespin Clip that has a screw hole designed to fit a tapered screw like a drywall or construction screw
Parametric f3d included for making custom sizes. These spacers are designed to match the width of the screw head. Public domain license. For smaller sizes get the Metric Screw Spacer Mega Pack 1 - Sizes M1.6 - M12
The actual outer diameter of the fitting is 1/8" smaller than nominal size so that it can fit inside of flexible duct. Disclaimer: Not yet print tested. Printing Notes Lightning infill is advisable because of the large empty void.…
If blobs are seen on the strings between the posts, the filament is definitely wet. Strings are ok as long as they are smooth and fine.
A functional prop inspired by the look of the Advanced Wiring Kit item from Subnautica. Printing Instructions No supports are required. All pieces can be printed with lightning infill. Glue is recommended but most of the pieces, aside…
Decorative obelisk found scattered around areas where Precursors had been working. Tree supports are recommended. The two-piece version uses less support material and can be glued together.
Prints without supports but make sure to turn down the speed on overhangs - the largest piece has a challenging overhang. Use CA glue to assemble. Some sanding may be needed where the lower 2 pieces fit together, especially if your first…
A conveyor belt styled shelf to help keep your factory tidy. Print and Build Instructions This shelf is designed to be built using the included printed fasteners without any extra hardware or glue, but can be glued for more strength. Hot…
Prints without supports but make sure to turn down the speed on overhangs - the two largest pieces have challenging overhangs. Use CA glue to assemble. Some sanding may be needed where the lower 2 pieces fit together, especially if your…
This panel has screw holes on all 4 sides so that it can be hung in 4 different orientations. There are several different tile designs that are used throughout the QEP, but this is one of the most interesting and most frequently used…
Tested as small as 50%. At smaller sizes the tabs can break off more easily. Flexible filaments will be able to go smaller than brittle ones. At 50% (as pictured,) a USB cable can easily be fed through.
Cap fitting for 1-1/2" DWV pipe
I remixed this adapter plate to make it possible to raise and lower the Stealthburner and BL Touch
KitBox is my attempt at creating a free and open platform for customizable tool cases. Core Features / Project Goals Sturdy outer Shell Modular Inserts for customizable storage Integrated handle Cam-locking buckle closure for smooth and…
This panel has screw holes on all 4 sides so that it can be hung in 4 different orientations.
Connects a shop vac hose to a miter saw dust port. Most likely will fit many other tools like belt sanders, planers, etc
I sized this to fit my 400mm printer but it can be scaled in the slicer to fit your printer and step height. Printed with Polymaker Army Beige PLA, 10% gyroid infill, zero bottom layers so that it would bond well with the liquid nails…
The non-knurled option prints fastest.
This is a challenging print. For best results use organic supports, making sure that the Branch Angle is set to a high enough value that the overhangs get fully supported all the way around . A branch angle of 60 degrees seems to work…
These can also be used for ducting, cables, conduit, etc. I usually install these with acrylic painters caulk, adding some to the inner circle and around the outer edge for a finished look and air tight seal. Can easily be primed and…
Print with the model oriented vertically, and scale to the desired height in the slicer. Brim or raft may be required in order to prevent movement and detachment during printing. For best results use a printer that supports Pressure…
This model can be tricky to print and assemble because of the fragile corners of the “shell” piece. At 100% this model will be fairly large. It can be printed as small as 50% (pictured) but it is more difficult to build at that size…
Print with the model oriented vertically, and scale to the desired height in the slicer. Brim or raft may be required in order to prevent movement and detachment during printing. For best results use a printer that supports Pressure…
The countersunk screw hole is designed to fit standard #8/#9 drywall/construction screws. Update: Now includes 2 variants, with or without tabs. Single cable remix here: Wall Cable Holder for 1 x 1/4 In Tubing or Coax cable
Includes 105 pre-rendered STLs in 21 sizes x 5 weights, as well as the fully parameterized f360 source file so you can tweak the parameters and create custom brackets. Update: Modified the model to use fillet on the top and chamfer on the…
Hangers for suspending plumbing pipes, 1/4" to 12". Parametric f360 file included for making custom hangers.
Print standing vertically with the mounting plate sitting flat on the printer's build plate. No supports required. Brim is advisable, though I was able to print the one pictured without any brim. Size test print included for dialing in…
Print with the model oriented vertically, and scale to the desired height in the slicer. Brim or raft may be required in order to prevent movement and detachment during printing. For best results use a printer that supports Pressure…
Square notches in 1/8" and 3/6" on the 2" sides and optionally ¼" notch on the 3" side.
The two halves fit together and can be glued onto the wall using acrylic or silicone caulk. A variety of flange widths and weights are included. Scaling All included STLs are rendered for a pipe diameter of 100mm. In your slicer, scale…
Several heights are included as well as a hollow variation. The planter in the photo was printed with Overture Silk Neon Green.
I designed this bolt to go with my miter saw crown stops: Crown Stops for Miter Saw Included parametric file can be modified to create other sizes of bolts. The flat channel down the center of the bolt allows it to be removed with a…
Includes 5 height variations as well as a No Support version. With enough cooling it is possible to print the regular version with no supports as well.
Inspired by the shape of Resin/Plastic/Rubber/Silicone resources in the game Astroneer.
Includes multiple pre-rendered weights as well as parametric source files for making customizations or remixes. Print sizes start at 308mm.
I made this to connect a Makita XDS01Z to a BucketHead wet/dry vac. Tapered fit to 31mm OD on both sides.
Designed to work with most drywall or construction type screws.
I'm printing this with 2 perimeters, 2 bottom and 4 top layers, 10% cubic infill. Cost is 61g. Public domain license. ♡
Glue and smooth into place using paintable caulk eg Dynaflex 230. The tapered foundation should be recessed behind the trim. Paint to match the wall. Includes 2 extra variations: "Short" lacks the tapered foundation and is useful for…
You may need to scale this to fit your closet's knob - by default it fits a knob w 28mm base. Print with wood filament or paint to match. 3 designs plus plain included, along with source .f3d files.
Scale the center connector vertically as needed, multiple pieces may be required to fill the space between the two end parts. The end pieces still will have a bit of a corner that might need to be sanded down. Alternatively they could be…
These are all currently available results.
