Counting matching models…
I was looking for a minimal case for the Heltec LoRa 32 module. The cases I found either also offered room for a LiPo and a power switch, were not designed for the new solid LoRa antenna, or the module just did not fit properly. So I…
Do you still have some strips of 110 film that were used in pocket cameras back in the 1970s and 1980s? And do you have a Plustek OpticFilm scanner? This is a film holder for 110 films. Just place the film strip into the holder, put the…
This is a very simple fume extractor for soldering. It uses an 120mm PC fan. The air is filtered by activated carbon filter sheets that are used for kitchen hoods. New: There's also a funnel now. It replaces the fan grill. Printing…
This is a case for Sven Petersen's Diag64cart , an open diagnostics cartridge for Commodore C64 and C128 computers. The main work was done by Laurence Gonsalves who published the OpenSCAD source code of a customizable C64 cartridge (CC…
This is a simple frame for the ByteDelight ZX Diag Cart for the Sinclair ZX Spectrum. I didn't want to use the rubber feet, but preferred something that was looking a bit more professional. 😉 The diag cart is just clipped into the frame.…
SFX form factor power supplies are a good replacement for the original Amiga 4000 Desktop PSU, because they fit well into the same space. This printable is a frame that fills out the empty space below the PSU, gives room for ventilation,…
This is a remix of the Gotek Floppy Case by NEMike . What I changed: The four mounting holes on the bottom are extended to fit M3 screws. There is room for M3 nuts on the side of the frame, so the M3 screws hold firmly. This is required…
This is a frame set for the Retro Chip Tester Professional (RCT) by 8bit-museum. The display frame is used to hold the display in place. I used an OLED display having mounting holes with 2.5mm diameter, but 3mm holes should work as well.…
The thread in the original cap broke, leaving a puddle of silicone grease on my shelf. To my surprise, I found no models for plain replacement caps, so I made one. This is a simple modification of a lube injector cap from uepsie that I…
The Ultimate II+ Cartridge by Gideon's Logic has an optional Tape Adapter. Unfortunately the adapter does not come with a beautiful case. I looked for case models, but found none that I liked or that could be printed without supports.…
PowerShark is an USB-C power supply for the Amiga 500, 600, and 1200. Unfortunately it is delivered in a “dust grey” case that does not really match to most Amigas. With this replica case, you can now print your own case in any color.…
This is a frame for a luftdaten.info compatible particulates sensor. The original sensor is housed in drain pipes, which is cheap, but also looks quite like that. 😉 This construction uses an OBO Bettermann T60 junction box, which looks…
NOTE: This model does not fit to the GOEX drive r.2023 or later. After adding a RGBtoHDMI converter to my Amiga 500, I had the problem that I had to get the HDMI signal out of the case. There is also a GOEX SD disk drive simulator in my…
The original Atari ST PSU can easily be replaced with a MeanWell RD-35A . However, what I disliked was that the mains wires were not fixed, and the terminals were not protected from accidental touching. Read my blog article about the…
This frame is used for an iRiver iHP-100/iHP-120/iHP-140 CF card modification. The CF card and CF card adapter is smaller than the old 1.8" HDD. This frame can be used to fill the space and keep the CF card from loosening. See this blog…
NOTE: This model does not fit to the GOEX drive r.2023 or later. After adding a RGBtoHDMI converter to my Amiga 500, I had the problem that I had to get the HDMI signal out of the case. There is also a GOEX SD disk drive simulator in my…
This is a replacement for the Braun Juicer 4161 switch spring (part #81262218). The original part got some fatigue cracks over the years. I was unable to obtain an original spare part, but I didn't want to throw away a good juicer, so I…
As an alternative to the ZX Spectrum TV modulator, redhawk668 created an S-Video modulator board. The original construction uses two nuts to keep the modulator board separated from the mainboard. I prefer to use this 3D printed base…
This is a rear trapdoor and a holder frame for the HDMI output of the Individual Computers Indivision AGA MK3 on an Amiga 1200. The design is specially made for A1200.net replica cases, and may not work for classic Amiga 1200 cases. It…
This is a PC slot bracket that holds a Gotek floppy drive emulator in place at the back of a PC case. Bill of Materials This print, of course Gotek board 3x Self-tapping screws for plastic, lens head, 3.0 x 8 Printing and Assembly I used…
This is a control panel that is meant to be mounted to the front of a Commodore Amiga 1060 “Sidecar". It controls a Gotek drive that is mounted to an expansion port slot . Bill of Materials All three printed parts A Gotek drive (with…
Are you annoyed that the TaoTronics TT-DL12 desk lamp can only be rotated within a narrow angle? Just print this ring and put it on the lamp base. After that, you can rotate the lamp in any angle. No modification on the lamp required.…
These are all currently available results.
