Counting matching models…
Vent is separated to three parts and they are joined together with M3 screws. As insect protection you can buy cheap insect protection screen, cut it and glue from inner side. For assembly you will need 8pcs of countersunk M3x10 and 8pcs…
Part numbers: DBC101690, AWR6711, DBC101680, AWR6712 --------------------------------------------------------------------------------------------------------------- On thingiverse is similiar model, but without locking hook. I had done…
Few hints for Land Rover Discovery II sunroof repair: I recommend silicone grease for rails parts. Use butyl tape as outer sunroof to car body seal. I used this tape also for sealing the four window nuts. Seal drain corner with quality,…
10inch rack holder for NVR unifi protect instant. Printed from PETG, holes are 5.8mm, so M6 screws can be directly used. Use big zip tie in the middle, as shown on the photo. Tight litle bit more, for firm hold. NVR can easily slide…
I didn't find LR part number for this, but this part should be same as BMW 17111719190 Replacement for water expansion tank holder (bracket?). Should be printed from high temperature resistant material, because of higher temperatures in…
Lay tilted on bed for better layer strength:
Because I have sleeping bed and foldable table in car, the original inner door handle was inaccessible and closing was problematic. So I created this handle which can be used also as handle for tailgate opening or closing. Installation is…
I wanted to add oil pressure, ACE temperature, engine head temperature “watchdog” in to my car. I found device called UTCOMP-PRO with possibility to connect OLED (SSD1322). This holder fits (snug "click") very nicely. to dashboard, thanks…
The windscreen service man lost nuts, plugs and crack hooks. So i remodelled missing components of the cowl (PN: JAK000010PMA ). Plug - product number ECZ100000 Plug can be printed from PETG on textured sheet with small supports on. PETG…
10inch rack holder for Mikrotik. With this it can be mounted only from behind, because hAP ac3 (ax3) is too wide to stitch it between rails. Printed from PETG, holes are 5.8mm, so M6 screws can be directly used. Use organic support for…
I printed it from PETG (3 perimeters) and sandpapered. O-ring sizes, which I used: Recommended material FPM75 (Viton). Smaller: ID:25mm TH2.5mm Bigger: ID:27mm TH2.5mm…
Some another clutch tips: TD5POWERSLAVE is really good for long travels. Pedal is much softer. On some LH cars is clutch pressure sensor on the right side. It is possible to mount this sensor directly to unused hole inside of a main…
Seal can be pushed with old or new nut. When the tool is fully in, the securing part of nut is still outside of thread. FTC4939 text was added in PrusaSlicer. FreeCAD file attached. I used PETG, 4 perimeters, 30 % infill.…
Print 4 pieces fron ABS or PETG and use long enough zip tie.
Animals can be stacked each to other. Side animals are connected with wooden sticks (3mm diameter). Narrow tapes can be placed on ears or tail of smaller animal on top. ---------------------------------------------------- Zvířátka se dají…
Should be printed from TPU. FreeCAD file attached
My MPCNC had noticeable backslash on Z axis, so I added same lead screew nut to the bottom of Primo core. This model is created in FreeCAD and project file is available for download. Should be printed from PETG with layer height 0.2mm.…
Output shaft seal installer tool. Seal must NOT be pressed fully in, because there is oil hole behind (as you can see on photo). Works even with the ring installed. Internal grooves prevent the shaft from rotating during tightening.…
I used PC/ABS blend and 6 perimeters. PETG should be also fine. For best strenght you can print nut as one piece (and also add the bolts). But removing the leadscrew endstopper can be tricky. For replacement without removing endstopper,…
Print from TPU, because it is flexible + good layer adhesion. Horizontal_floor_nut_lockut-nut_lockut_RTC3746 you can use, if your material layer adhesion is poor. Should fit on: Discovery 1 (1989 - 1999) Discovery 2 (1998 - 2004) Range…
These are all currently available results.
