P
Printablesttt126
191853696 Tow hook cover front Golf 2 VW
Tow hook cover at the front as it is no longer available, a 3D part was made. not quite original but good enough. PETG printed.
- Downloads
- 416
- Likes
- 50
- Rating
- 5
All models
Counting matching models…
P
Printablesttt126
Unifi AC 6 Pro Stand
A stand for an Accesspoint 6 pro from unifi. The lan cable can be routed through the bracket. The aim was to place the AC point on a high shelf. It is printed in 2 parts and glued together with a sleeve.
- Downloads
- 389
- Likes
- 67
- Rating
- 5
P
Printablesttt126
Anchor Handling Tug boat, the Fairmount Summit Bridge Top
Comes in two Parts. The upper Bridgepart of a RC Scale Boat, around 1:45 Scale. Takes 8.5h one Part. The main house are 3 parts.
- Downloads
- 306
- Likes
- 31
- Rating
- 0
P
Printablesttt126
Tow hook cover back Golf 2 mk2
Tow hook cover back Golf 2 mk2, not needed but nice to have
- Downloads
- 254
- Likes
- 25
- Rating
- 5
P
Printablesttt126
Subaru Outback 2024 Gen.6 Phone Holder
The only resonable place to attach a telephone is on the center tunnel on the right (with left-hand steering). Made from 2 parts so that you can adapt the holder to a different mount. I use a 40mm magnetic mount. Printed with Gyroid…
- Downloads
- 214
- Likes
- 36
- Rating
- 3
P
Printablesttt126
Golf 2 holder for ignition cables and injection lines
holder for ignition cables and injection lines in the engine compartment 6,5mm Ignition and 7,7 Injection line.
- Downloads
- 195
- Likes
- 28
- Rating
- 5
P
Printablesttt126
Garmin Zumo GPS Mount Husqvarna Norden 901
Modular Mount. Baseplate to be added to a GPS Mount/Stant for an Garmin Zumo. Can be changed to a differnet GPS by doing a new GPS Stand. V2 of Garminhold is 1 cm lower above the TFT so it didnt block the airflow.
- Downloads
- 140
- Likes
- 5
- Rating
- 0
P
Printablesttt126
pi 3 rack mount 10 zoll OLED
pi 3 rack mount 10 zoll with OLED for a Volumio Instalation in my Garage. It will be equiped with a AMP2 hat. OLED really not necessary but fun :-) Bus is 3c for the OLED plugin.
- Downloads
- 112
- Likes
- 15
- Rating
- 0
P
Printablesttt126
Reolink Doorbell Roof
A rain cover for an angled mounted doorbell from reolink. There are 2 versions available. One for right and one for left angled. A sheet of zinc is glued into the circumferential groove. I used 2k glue. The projection and shape of the…
- Downloads
- 93
- Likes
- 20
- Rating
- 0
P
Printablesttt126
Free falling Winch RC Ship
Free-fall winch for RC boats, featuring a slip clutch. Simple construction. Required components: two 11x4x4mm ball bearings, one spring, brass tubing (4mm outer diameter, 5mm outer diameter with 4mm inner diameter), and one microswitch.
- Downloads
- 58
- Likes
- 11
- Rating
- 0
P
Printablesttt126
Typ XXI RC U Boot 1:48 Motorcompartment
A few additional RC parts for my Type 21 U boat from rcsubs.cz. A waterproof motor nacelle to accommodate two 35mm brushless motors. Shafts sealed with 15x6x5 oil seals and a screwed-on cover. Can be bolted to the original mounting points…
- Downloads
- 54
- Likes
- 7
- Rating
- 0
P
Printablesttt126
Heater vent key 5mm square
Heater vent key 5mm, nothing else to say
- Downloads
- 39
- Likes
- 2
- Rating
- 0
P
Printablesttt126
Key for cover to adjust ignition timing
If you want to adjust the ignition timing, you need a 27mm nut to open the cover to the sash gear. this is a key for exactly that. It should only be tightened hand tight.
- Downloads
- 37
- Likes
- 1
- Rating
- 0
P
Printablesttt126
Gyroscopic stabilization System
A gyroscopic stabilizer for RC model ships. Built around a G-Power BL motor, 2225, 2000KV, 6-11.1V. Two versions available: large with approximately 110g flywheel mass and small with 50g flywheel mass. Each uses the same drive.
- Downloads
- 34
- Likes
- 4
- Rating
- 0
P
Printablesttt126
Allskycam housing pi4
I wanted to build a motorized allsky camera. The basis is a Pi4 and an HD camera as usual. The motion control is regulated via an Arduino Nano with Steppershield and DHT22. During the day, the camera should not be exposed to strong UV…
- Downloads
- 28
- Likes
- 3
- Rating
- 0
P
Printablesttt126
Graupner Rau IX
A few parts for a Graupner Rau IX. See photos.
- Downloads
- 25
- Likes
- 3
- Rating
- 0
P
Printablesttt126
Battery Box for Norden 901
Battery Box for Norden 901 to house a LiFePO Pack with Balancer, 150x87x105mm, plus left hand, m3, petg
- Downloads
- 23
- Likes
- 1
- Rating
- 0
P
Printablesttt126
weatherstation esp 8266 D1 mini
Weather station built around an ESP8266 D1 mini. Rain sensor rs12. For mounting on a 40mm mast. 12v input is brought to 5v with a dcdc step down converter. It is important to read the BME280 max. every 5 minutes, otherwise it will heat…
- Downloads
- 23
- Likes
- 6
- Rating
- 0
P
Printablesttt126
Subaru Outback 2024
small part for a Subaru Outback 2024 Small insert for the compartment in the center console to hold a remote control for a garage door. with indentations to cover it with leather.
- Downloads
- 22
- Likes
- 9
- Rating
- 0
P
Printablesttt126
Unifi AC Pro Raincover
A rain cover for horizontal installation under a small roof overhang. To be used with the original holder.
- Downloads
- 21
- Likes
- 2
- Rating
- 0
P
Printablesttt126
Aqara FP2 Wall mount
Aqara FP2 Wall mount 45 Degrees. Power supply goes inside a so called “UP-Dose” :-)
- Downloads
- 20
- Likes
- 1
- Rating
- 0
P
Printablesttt126
Riva Aquamarin
Cockpitframe for illumination Riva Aquamarin from Amati
- Downloads
- 15
- Likes
- 0
- Rating
- 0
P
Printablesttt126
Subaru Outback (Gen 6) Cargo Area Light Upgrades
A revision of the light upgrade by Justin Lamply with a black frame and transparent lens. Rear unit also converted to star board. Both parts are connected with a drop of superglue. Lenses needs support. update: After I was unable to…
- Downloads
- 12
- Likes
- 8
- Rating
- 0
P
Printablesttt126
Art déco ceiling floodlights
A lamp project based on the art deco period. Lampshade printed in PETG, lense in clear PETG all other parts in PLA. Covered with gold and aluminum metal. Foot filled with screed concrete, approx. 5kg. Height of the lamp approx. 175cm…
- Downloads
- 11
- Likes
- 2
- Rating
- 0
P
Printablesttt126
BMW R 100/80 GS Voltmeter
Ein Gehäuse für den Blindschalter einer BMW R GS. So kann man ein 0.28 zoll LED Voltmeter einbauen um die Ladung der Batterie zu überwachen.
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
Printablesttt126
Signallight Mount Front R100GS BMW
Its just a simple Mount for LED Signallight on an BMW R100GS. M8 Mount.
- Downloads
- 7
- Likes
- 4
- Rating
- 0
P
Printablesttt126
Druckraumheizung 3D Heating
Eine Heizung für den 3d Druckraum aus einem Steckdosenlüfter 500w und einer Temp.Regelung. Wenig Lötarbeit. Alle Teile der Geräte werden weiterverwendet. Die orginal Rgelplatine des Lüfter regelt nur bis 30 Grad, wird ersetzt durch ein…
- Downloads
- 4
- Likes
- 1
- Rating
- 0
P
Printablesttt126
Synchtester 2v BMW Boxer R100GS
A synchronization tester for a 2-cylinder boxer engine (R100GS), built with an Arduino Nano and two pressure sensors (5V, MPXH6115AC6U). The reset button is accessible externally to reload the program at any time for a neutral…
- Downloads
- 2
- Likes
- 2
- Rating
- 0
P
Printablesttt126
Mount for a Hella auxiliary headlight - R100GS
A mount for a Hella (HELLA LED Lightbar Black Magic Zusatzscheinwerfer 6,2 Zoll mit Zulassung) auxiliary headlight on a BMW R100GS. The mount clips onto the crash bar rather than being screwed on, making it easily removable. It needs to…
- Downloads
- 0
- Likes
- 1
- Rating
- 0
These are all currently available results.