Counting matching models…
I love this design by mbrady because it sends air where you want it, rather than randomly blowing it away like the top down models do. I oriented my Octopus so this blower shoots the air straight out the back of the base. I used a nice…
This is a Dremel / Rotary tool cutting mount for precision cuts of rods, screws, bolts, drill bits, tubes and more. I wanted to do the Pin Mod on my Voron 2.4r2 and I didn't have an accurate method to cut the pins to size. I ordered the…
I was concerned about heat for this Sovol SH02 dryer at the hottest temperature so I made a riser. I kept it open as I wanted airflow underneath. It simply inserts over the existing feet (with decent tolerance so you won't have to worry)…
I just wanted some braces for my 2.4... then I went for a single piece front door without any clips to secure it. I didn't like the hit on my input shaper results when I made this change and so I designed these. Let me be honest, it…
Remixed to make useful with a Eureka Mignon on a tilted base. It may also be useful for people who want the holder to retain the dosing cup more securely without a tilted base. Have also included a version for different size dosing cup…
My dad always told me you don't #### where you eat. Different principle, but probably best to not do it where you clean also. I have a little bin where my nozzle is cleaned by a brush at the back of my 2.4 350 enclosure. This bin works…
This is a nozzle scrubber with a bucket / bin for Voron 2.4. I use it on a 350 and it lines up with the edge of the bed. This remix addresses two issues: The original wasn't wide enough and I would find bits would fall out the side The…
This lightweight tablet stand will support your tablet in landscape or portrait with or without the case on. I've tested with an iPad pro 11 inch and Android 10 inch tablet. I would suggest printing with the following settings: 15% infill…
The serial bot wasn't producing so I made my own to fit a neat little spot between braces on my v0. I figured other people may want it as well. I went for something subtle in black. The length is designed for the gap I had. I have also…
I've created a fresh set of napkin (serviette) rings that will look very at home on any dining table. They will add that finishing touch to the table for a celebration event (like Christmas). I had cloth serviettes growing up. I actually…
Designed to a minimal size for integrating into other prints. Excuse the bridging quality in my photos!! I printed in ABS and so printing in other materials might introduce slightly more tolerance, but still good fitment. I have used…
Cam lock that visually shows you when it is in the open direction. I had found my v0.2 r1 cam lock would often move out of alignment when the lid was open. With a hex this was hard to tell. The arrow points to the opening to resolve this.…
This is an insert for the Sovol SH01 that works with 3010 blower fans directed through ducts directly at the source of heat for significantly better air distribution and improved heating. The result is faster heating, less hot spots in…
Flextail Max Repel 3-in-1 Tripod Stand. Stand. Protect. Mount. I needed something small to take the Flextail Max Repel on a holiday to deal with mosquitos carrying disease I don't want to catch. I also needed to be able to use it in…
Some times you just need to slap a wago on a print to connect wires. Grab the stl, add it to your slicer and WAGO! I created a mount designed for integrating with other designs for the 221 Wago Wago 221-413 / 221-412 / 221-415 Simply…
I wanted a large tray for my center console to store things I needed. I found the one that came with the car too small and reaching in too difficult to find key things. Print with supports for the lip so that you get a good quality base.…
I needed a cover for my Samsung SmartTag 2 so it wasn't going to be accidentally pressed when travelling overseas while in a bag. This cover could have a phone number imprinted in it. I also have a little name sticker underneath with…
When I built my Voron 2.4r2 I attached the exhaust housing as per the manual and began printing. About 100 hours in I realised that my back panel had begun to make contact with the rear belts causing minor defects on prints. With closer…
This is a cheap and effective webcam for the Voron V0. The module only costs ~$5, cable a few dollars and the result is excellent. I remixed the one by SvB to create more clearance for the longer leadscrew on my Moons Motor (included in…
A simple screw sorter that integrates measurement for M2, M3, M4, M5, M6, M8 as well as lengths up to 24mm. Version 2 I spent 2.5 hours sorting screws, bolts, washers and discovered I would do things differently and wanted to be able to…
Update - I have now moved to a new design that better suits my needs. https://www.printables.com/model/757443-eureka-mignon-dosing-cup-holder Simple setup for a dosing cup for use with a Eureka Mignon. I always weigh before I grind into a…
Attach a 2020 extrusion to a 2020 extrusion like a roof rack or a VHB mounted something. There is also a 2020 wire guide. All are oriented for printing. These mounts have feet and plug in firmly without even using a bolt and so they are…
My intent is to help or inspire v0.2 builders. Send me a PM or drop a comment and I'll try to help. This is a catch-all for some of my previously unreleased mods to make them available. I've also listed some of the mods I used from others…
A simple print to fit the need of getting the wrists at the right height for typing. These leather rests work with a particular ergonomic padded product that isn't high enough, but super cheap at places like this…
I wanted the cirque as close as possible so that I didn't have to reposition my hand to use it. The original ZodiarkPi had it mounted higher. This case is the result of my reworking. Parts Used Based on the ZodiarkPi my Aleblazer. PCBs…
I bought what I can only assume was a fake FA-400. Either way, it had a look only a mother could love (or a fanboy) and a sound that needed taming. First I installed silicone washers. This worked well, but I found the shape inconvenient…
I wanted to be able to carry my drywall / plaster saw without worrying about it ripping up my bag. Currently it has a super deadly double-sided blade. It also switches with standard reciprocating saw blades for manual versatility. This…
I have a Soocas X3 toothbrush and the battery life is ridiculous. As a result I don't use the charging stand very often. This original stand is bulky and has a power cord attached. My design is compact and has a holder for the Soocas…
I have a kmart anko rectangular bin and the hinge broke. This meant the lid kept falling off. So I designed a quick spare part. Very satisfying. This is the bin https://www.kmart.com.au/product/30l-white-rectangular-bin-42747918/ It was…
These are all currently available results.
