Counting matching models…
Exhaust duct for my Elegoo Centuari Carbon and painting booth. Needed a solution to split in-line 4" fan to both so I remixed this very good design created by @DOOM. Each inlet has a check valve with a lever. OD: 3.8"/96.4mm Parts Needed:…
I changed the holes so you don't need some crazy screwdriver or additional holes through the other side for the screwdriver to reach the screws to mount it. Now you simply loosen the screws a little and slip the slide on. This is a little…
Print with the smallest nozzle and layer height possible with a brim. It's a pain to remove the brim, but it fails without it. I use scarf joints on the seams. The diameter of the gas port on the barrel I was using this for was ~1.8mm,…
This allows you to mount your Allen wrenches (hex key wrenches) to multiboard. Designed specifically for the harbor freight SAE wrenches: 3/32", 7/64", 1/8", 9/64", 5/32", 3/16", 7/32", 1/4", 5/16", and 3/8"sizes. Designed for 0.2mm layer…
This is a wall mount for a Shark hand held vacuum with a charge port. This should fit the following models CH901, CH950, CH951, and CH955. I added a recess for the AC adapter so it stays put.
Mount for the Midwest Industries AR-15 Lower Receiver Block on Multiboard. Connects to multiboard with snap fit. All I did was take a lower receiver STL and cut it up, it's quick and dirty but works. Print using your standard settings.
This is a wall mount for a Shark hand held vacuum with a charge port. This should fit the following models CH901, CH950, CH951, and CH955. I added a recess for the AC adapter so it stays put.
Very simple part, probably impossible to mess up. If you don't have AMS pause at the top level and you can change the text color. The inside dimension is 17.5mm and it fits snug on the post I have however there are different post sizes…
Name says it all. I printed it in ABS with supports. There's a million of these out there but none were exactly what I wanted so I threw this one together.
I scaled this to fit the air duster. The original 3d object was 2mm across for some reason. Upgrade your workspace or garage setup with the Fanttik NEX B8 Ace Wall Mount , a durable and sleek storage solution designed to perfectly hold…
Single Piece - No lid to accidentally come open Secure - internal geometry makes it nearly impossible for blades to fall back out. Space saving - 45x45mm footprint Tall - Holds larger blades like “window scraping” blades IMPORTANT Print…
Simple storage caddy for the Last Meter Epoxy Mixing Tray. Fits both the original and remix.
A multiboard organizer for gun cleaning jags and brushes. Holds jags, bore brushes and chamber brushes, with the standard 8-32 thread. Pockets on the sides hold Pro-Shot muzzle guards.
A holder for 5.56 & 6.5 Creedmore Go, Field & NO-GO Gauge with a multiboard snap mount.
If you're like me you constantly lose these and have to sacrifice an allen wrench every time to make a new one, so I made a dinky little mount to hopefully prevent that from happening in the future. Simple as they come. If you need help…
Pretty simple and straightforward, I printed in ABS with supports, but anything will work I'm sure.
This is a charging cradle for the Xiao nRF enclosure for sma antenna meshtastic meshcore by @dremial_8 which I created combining the stand and this model by @BradAustin which allows the device to stand upright while charging or while it…
I'm not a medical professional but I am an Eagle Scout and in an effort to be prepared I needed a way to prominently mount an emergency bleeding kit so I created this simple model. It's nothing special but it gets the job done. I prefer…
I added holes for the LED's. You may get the back cover from original design page.
Combination of both the LED cutout and switch provision versions of the integral antenna model. This is the switch on Amazon: https://a.co/d/0gSnlvK3 . clip off 4 of the 6 leads, and shorten the other 2. needs a tiny drop of superglue to…
Very basic mounting arm for the Black&Decker model HFVB320J27 Lithium Flex 2 Hand Vacuum. (probably a bunch of other models too, they made a bunch with the same form factor) No frills or anything special, but it works. I printed in PLA+…
See original model for info and printing instructions. BC-250 SteamOS — Turing Smart Screen 3.5" Setup If you're using a Turing Smart Screen TURZX 3.5" with your BC-250 Steam Machine, there's an excellent open-source monitoring dashboard…
These are all currently available results.
