33 models
All components to print a center insulator, end insulators, and line tensioners to build a QRP dipole antenna for ham radio. I designed this for use with 6-32 screws, 18 gauge wire, SO-239 connector and 550 parachute cord. The antenna…
Prints a bolt ¾" long along with a matching nut and washer all ¼" x 20 thread.
Storage of 550 parachute cord, 2 slots allow the ends to be secured.
Jersey barrier model scenery for slot car or train layouts 1/24 scale. The example shown was printed 100% the model is scaled 1/24 but changing the printer size could modify it.
Slot car or train layout scenery. If printed at 100% it scales 1/24. The examples shown where paused during printing to change fillament colors.
Stencil, A - Z, 0 - 9, Common symbols. Prints a stencil with capital letters and numbers .5" high when printed 100%. Printing in transparent PETG would make this stencil easier to use.
If printed at 100% the scale is 1/24. The examples shown where paused during printing to change color from black to orange.
The clips will push into the aluminum work surface used on the Snapmaker machine when set up for work with laser. One side pushes against thick work, the other will hold down paper or cardboard. I found the rubber pieces that Snapmaker…
Key fob will print 3.75" long at 100%. The printing is indented, I suggest printing this with 2 filament changes. The model in the photo was printed with red then white and then red so the lettering shows well. Added a blank version to…
The 2 STL files will print the 2 halves of a storage device for the probes used with a meat thermometer used for grilling smoking or roasting meat. I designed this around the ThermoWorks probe so the probe will store neatly without velcro…
If printed on edge no support is needed but bed attachment can be a challenge. Eye on top will accommodate a thin cord to allow easy removal and a way to secure the stick into the bag.
A simple lid pry tool designed to open standard size mason jar lids. Properly sealed jars can be difficult to open and I have chipped the glass brim by using a bottle opener. This tool made of plastic will be much less likely to damage a…
These 2 stl files will print a form and plunger to make 4.5 inch meat patties. I find this size good for ¼ pound hamburger patties.
Prints a bowling pin and ball in small scale. The pin can be printed in one piece without support. I added color stripes by pausing the print and changing filament. The ball is in three pieces to avoid support on the exterior surface. The…
Drilling jig to help hold and align round stock or tube when using a drill press.
Two silverware drawer organizers 12" x 9.7" and 7.5” x 9.7” when printed at 100%. The two separate organizers both are 9.7” wide. One is 12” tall with 7 compartments the other is 7.5” with 3.
A total of 15 parts need to be printed, no support necessary. All individual parts are included along with a card that will print everything at one time. My printer did a better job when each part was done individually. Added a slightly…
The two parts of this print along with an m3x10 hex head screw allow the replacement of the hanger loop on an ICOM microphone. Example IC-7300 radio.
Simple key chain fob that looks like a WW2 jeep grill.
Simple key fob that is patterned after a Jeep Wrangler front grill
Used double edge razor blades are still very sharp and dangerous to throw out. This container offers a safer way to deal with used double edge razor blades. Container will hold many blades and can then be disposed of when full. I…
If printed at 100 percent the bobber will be 1.4" in diameter. It will screw together, can be glued as well. The classic colors are red and white as shown in the attached photographs. Red top, white bottom, white center. Following up on…
A simple lid pry tool designed to open wide size mason jar lids. Properly sealed jars can be difficult to open and I have chipped the glass brim by using a bottle opener. This tool made of plastic will be much less likely to damage a…
Some parts must be printed twice, this is noted in the file descriptions. Printing all parts in the same color adds to the challenge. With correct positioning during printing only part 1 requires support.
I needed to mix small batches of epoxy glue so I drew up a little cup and stir stick. The walls on the cup .stl are thin .02" but I print this using the vase or spiralize mode to save plastic and speed the printing. The cups in the photo…
These holder/labels work as accessories to the QRP dipole antenna center and end insulators. When cutting a wire to make the two elements of the dipole antenna I like to cut about 12” longer than expected to allow for tuning. After lacing…
The post skirt is a 2 piece design to allow replacement of original 1 piece Timbertech post skirts that are cracked or missing without dismantling the railing or support post. The inside and outside profile closely matches the original.…
Files will print a ship's clock case that will accommodate an inexpensive quartz movement available from Klockit or Amazon. Included are multiple spacer and shim options for different clock shaft lengths. The clock face requires a…
These 2 stl files will print a form and plunger to make three inch meat patties. I find this size good for “sliders” and pork breakfast patties.
Our new vehicle is larger and judging how far to pull into the garage is a bit of a challenge. I drew up and printed this plastic ball to help. Suspending it from the ceiling with a light string at a distance that just touches the…
Similar to other post skirts I have drawn, these are 4" and 6" tall. 2 are required to trim a post. Note the interior dimension is exactly 3.5 and 5.5 inches. They may fit easier if printed a couple percent oversized.
Adapts 2 1/4" shop vac hose to a Dewalt radial arm saw eliminating the sawdust bag. Its offset to allow the hose to clear the saw. I found it prints best with the small diameter down.
Prints all components needed to assemble a model of a lateral navigational aid. All parts printed in red or green PLA except the light lens used clear PETG It can be wired to light with a 3mm flashing LED by using the following parts. I…
These are all currently available results.
