P
PrintablesIrons
Talon Magazine Bumper Thick Bottom
The bottom of the bumper is too thin, so I increased it too 1mm. Category: 3D Printing
- Downloads
- 203
- Likes
- 24
- Rating
- 5
All models
Counting matching models…
P
PrintablesIrons
Nerf / Worker Swordfish 21 Amp Switch Converter Plate
Switch plate and lever assist to convert the Worker Swordfish to use 21A microswitches. Make sure the thicker side of the lever assist faces towards the rev trigger. Category: Sport & Outdoors
- Downloads
- 31
- Likes
- 8
- Rating
- 0
P
PrintablesIrons
Nerf SPAMF Holster v2 (right leg)
Version 2 of my holster for the SPAMF. Uses velcro from velcro bundles in addition to straps that come from traditional holsters. I have not printed this myself yet, but it should work. I based it off of my older design. I use this…
- Downloads
- 27
- Likes
- 8
- Rating
- 0
P
PrintablesIrons
Nerf Mega Motostryke Paddle Mag Release
Replaces button mag release in Motostryke. Take out button and lever, but keep the piece that interacts with the magazine. M1 is a simple paddle. M2 is a slightly longer paddle with an extended bit for the index finger of the rand hand to…
- Downloads
- 23
- Likes
- 6
- Rating
- 0
P
PrintablesIrons
Nerf Rival Finisher Magazine Upgrade
This is a replacement tube that slides into the magazine for the Finisher. It enables the magazine to be opened, even with it empty. Simply unscrew the two screws on the top of the mag, and slide out the original tube, then replace with…
- Downloads
- 19
- Likes
- 5
- Rating
- 0
P
PrintablesIrons
Nerf Rival Kronos Pump Grip Picatinny Rail (for exposed magazine)
This is designed to be fitted over 1 3/4 inch PVC and the exposed magazine. The slots take 1/8" by 3/4" aluminum fat bars. The holes that fasten the bars are designed to take M3 screws, but can be bored out to take larger screws.…
- Downloads
- 15
- Likes
- 6
- Rating
- 0
P
PrintablesIrons
Caliburn U - Tuf Sear
A modified sear which takes the same size hex standoff included with the Caliburn U (1/4" x 1/4") There is a crack in the back of mine when I installed the standoff, but it runs reliably so far.
- Downloads
- 15
- Likes
- 3
- Rating
- 0
P
PrintablesIrons
Flared + Minimized Nameplates for Talon / Katana Magwell - Nerf Caliburn U
Some flared plates for the talon magwell version of the Caliburn U.
- Downloads
- 13
- Likes
- 3
- Rating
- 0
P
PrintablesIrons
Caliburn U - Durable IVI Stock
I added the newer geometry that holds the tube in place to the frontbutt, but without the picatinny, so that it doesn't snap. Category: Toys & Games
- Downloads
- 13
- Likes
- 1
- Rating
- 0
P
PrintablesIrons
"Nerf" Worker Swordfish Selector Hole Cover
This is a simple piece that slides into the hole in the Swordfish if you choose not to install the full auto kit. Category: Sport & Outdoors
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
PrintablesIrons
Caliburn U - Rail Delete Talon Mags
Simple smoothing of TCOG Back piece.
- Downloads
- 7
- Likes
- 1
- Rating
- 0
P
PrintablesIrons
Caliburn Name Plate - .50 Caliber
Name plate for U Channel Caliburn, indicating the size of the dart. Category: 3D Printing
- Downloads
- 6
- Likes
- 0
- Rating
- 0
These are all currently available results.