Counting matching models…
This is a gimbal and switch protector the the Flysky FS-I6X Transmitter. It clips on where the lanyard would go. It may work with the Flysky FS-I6 but I don't have a transmitter to test it on. If someone prints it for the I6 and it fits…
loved this case but the little knobs whore out almost immediately so I made it so that the cover has a nice and lasting snap fit Print instructions Print just like the original
Ipad Mini mount that uses double sided sticky tape. Uses 2 M3 Screw for hardware, holes are flashed over for better print quality. Category: Tablet
This is a filament dry box I made for printing nylons. It is inspired by the Markfoged drybox but way cheeper. This uses a Monoprice 9.9 L waterproof hard case and some PTFE fittings and tubing. It can hold two spools of 1KG filament. You…
Replacement numbers for Foosball table counter that uses 6mm rod
This is a lens cap for the AKASO EK7000 4K action cam. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: .15 Infill: 20% Category: Camera
Just made the screw flange surface thicker
Material: PLA layer height: 0.2 Shells: 3 Infill: 30% Electronics: Nema 17 with a Mechaduino controller, this is overkill but I had it on hand. Magnets: These are also overkill and too powerful, I would find smaller magnets and redesign.…
This is a little tool used to get the nuts of transmitter switches. This specific one was made for the taller tapered nuts found on the FlySky i6 transmitters. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No…
This was optimized for rigidity, by doing so the build plate is reduced by 5-10mm in the X axis. I also added an additional 4010 turbofan for added cooling as I am running this printer at fast speeds. If you are running a slower printing…
Description This was a fun project that was inspired out of a need. I had a very small bar with limited bottle space and eventuality ran out. I added these to expand the storage without taking up table top space and they worked fantastic.…
This is a modular mount for the Square Contactless Chip Reader. This allows you to easily move the reader to different locations, it is based off of the current Square system that they sell. You can put this anywhere like on the back of a…
USB Hub: https://www.amazon.com/dp/B09GJXVHVK?psc=1&ref=ppx_yo2ov_dt_b_product_details
If you don't care about seeing the filament or about it looking as nice here are the window files to print. I simply imported the DXF into Fusion 360 and extruded by 3mm. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No…
This is a stand for the RCA Voyager 3 Tablet. This is a terrible tablet to use in general but works perfectly as a nice cheep Octoprint display. The handle uses a 1/4-20 bolt and heat-set insert. Heat-set Inserts:…
So this is based of the Nurse Jamie Uplift massaging Beauty Roller. The significant other asked me to make it so she didn't have to spend an absurd amount of money for such a simple tool. This is the link for actual tool this is inspired…
This is an LED mount for the Matek Systems 7 Colors RGB LED board, I got them off of Amazon .It is used with the Usmile 250 quad also found on Amazon but should work with any quad that has the bars spaced around 31.5mm. LEDs:…
This can be made with all middle prints if desired, I included end pieces as well for those who really need it. works really nice because the dowels are 48" there is no modification, print parts, buy dowels and screws, then mount I print…
This is a remix of poofjunior base for his cable driven tool changer. With this version you can print the full base without needing the delrin reinforcements. This should be able to be printed as before with no supports Note: this is…
These are all currently available results.
