Counting matching models…
Here's a simple, two piece model to update your Ender style hotend mount to direct drive. It looks great and lines up really well. Kind of a bear to install, but I was able to do it without taking anything off other than the bolts holding…
This is a remix to fix the bracket to match the MK3S+ version X axis tension built in, as well as bringing it enough away from the bearing tube for my liking. This also fixes the mounting for the camera to use M2x8mm screws instead of…
I've been hunting for a y-axis tensioner that looks like it would be stock, but haven't found anything not insanely over-engineered. Like always, I finally landed on one I liked enough to remix. This time, it's from Thingiverse:…
Update May 10 2022: So it's been a year or so now since I made these. And I have to say, clearly no one printed it. I was reprinting in .10 layer height as well as printing thread into the pull instead of tapping it, just to refresh the…
Update: Ok so, after a summer of driving, this piece has definitely melted a bit. I assume literally being on top of the valve cover is not helpful. If printing this, you'll either need to make a new one every few months (or more in hot…
UPDATE: I did create a newer, slightly easier to print version of the left side emblem that also uses a rising sun instead of my duck. It's set up to only print a single color at a time. Find it under the ‘Single Color - v3’ folder. I…
My Datsun 620 is... weathered. I decided, instead of purchasing some decent used sun visors, to take my one good base and remake it. I initially tried printing with supports on the bottom, but it turned out really horribly. I hate…
I have an Icom IC-2730A, which uses an HM-207 mic. I had already created a nicer hanger for my Yaesu mic, but this one has a molded-in “bar” in which you are supposed to hang it from. Being cheap and thin sheet metal, I'm not one to use…
I really like the case design, but figured it needed a more "Prusa" flair, so I make the holes into hexagons! Also removed a bit of material in the captured nuts holes, since the way it was designed before, it would be a super thin wall…
On my quest to stop paying for things that can be easily made for my truck, my next stop was to model the inserts that hold the grille to the body, using the holes in the nose and tabs on the sides of the grille. Materials needed:…
I have a couple Yaesu radios, which use an MH-31 and MH-48 mic. The original hanger is cheap and thin sheet metal, which easily bends, so I created this holder. I believe I made this for #8 wood screws, due to naming the model the way I…
I needed a gasket for my original oil fill cap for my Datsun 620. The original part number 15270-78500 is now discontinued, so I looked at a picture and took some measurements, then made my own. My part number here is 15270-78501 to…
This is a holder for the ignition switch on a Datsun 620. My original clamshell is not in great shape, so the switch has been zip-tied to the column for quite some time. This just makes it look vaguely less… ratty? Created with a 5 degree…
If you need the adapter from the booster to master cylinder. I don't think you actually need the thin boss to use this, so the DXF doesn't contain show that at all. If printing, go with something high temp. I'm unsure if PETG would hold…
Just a DXF of the flange for a Nissan/Datsun exhaust manifold so you don't have to trace and cut. I will be sending this to a shop with a water jet to cut out of ½" or 12mm stainless. My Subaru exhaust pieces from Grimmspeed are ½", so…
Work in progress of a coil pack bracket for my Datsun 620, which has an L20B engine. It's designed with a 10 degree cant to help with the “approach” angle to the plugs. It's touching the upper heater hose, I so would recommend adding a…
This will replace the end caps, spacer, and create a mounting point that uses existing holes where kick panels go on a Datsun 620. I plan to mount on the right side (passenger side in the US and left-hand-drive countries), but I believe…
These are all currently available results.
