Counting matching models…
As the USB connector on my Sonic Pad always moves a bit downwards, I decided to create this extension. It clips onto the pad (as well as possible with the low profile of the Sonic Pad): The hole for the USB connector is made for this…
As I had some problems with removing (and inserting without a hammer) different types of inserts, I made my own version. This version has to be inserted in the correct way as it has a top (the thick side, see arrows on the back of the…
The holder with V2 fits to most machines, I tested with my tools like TE-CW TE-CD (2 different types) TE-CI The version V3 is 5mm more height than V2 and fits bit better to TE-Z machine, but the V2 works too. The holder fits tight, so the…
Because all the similar visualizer I found are either much to big (hit the fan on extruder head) or need magnet or fall off or are just “to much” I did a fast create of this small and easy version to clip on (5mm axis) the stepper motor…
Handle replacement. The M6 thread for the cables has to be cut by hand. For the 3 front screws, I heated the heads of the original self-tapping screws and turned them in to "melt" a proper thread form. So the holes are a bit closer, 2mm.…
Because I need to be more flexible with my cable storage and the usual comb design does not hold the plugs and connectors in place and the cable gets bent, I created this version to be placed on my HSWs. Basic elements: 3 slots, for…
I built a box for shelly Uni because I use them for tripple-temperature monitor and for save plug-in-sockets I use aviation sockets which are bit bigger than jack-plugs or like that. But I can screw them to keep in place and with…
I bought a PTC heater to build my own filament dryer that would allow the hot, wet air to escape instead of being trapped in the box like "professional" dryers do (bad design!), but the mounting was not very user friendly, so I created…
A case for a well known active balancer board. I used melt-in threads, the board comes "upside down" because the parts that can get hot are on the other side. Make sure the cover is placed correctly over the transistors.
Because I had problems with the original version of this good design (they fell out, maybe tolerances on the containers too), I took the idea and redesigned it from scratch, but added some sort of "springs" to it so it fits tighter. I…
To mount the BT dongle of my Daly BMS, I made a holder that also holds the USB plug in place. It fits tight (depending on printer tolerances of course) - but it should be a one-time thing - so I like it. Maybe scale it up by 1% or so if…
To protect the original Key from Kia cars I designed that protection Cover. I printed of TPU 98A, I used supports, depends on the bridging capapility of your printer. To insert the key flip in the bottom end first. The key should fit to…
The original never was sealing enought, were not stable to keep the gutters “in line” and had a step inside - doesnt make me happy. So I designed that one, for using a 2mm foam rubber (available self adhesive in diverent versions) as…
To hide the ESP32 for my WLED project I designed this case that fits for ESP32 Mini versions. I used an DC-Plug 5.6/2.1mm that comes from my Power supply, an XT30 plug to connect the stripe to the power, so that everything can be…
I built some hooks for a ordinary ¾" garden hose to keep them in place where i wont and not disturbs me (on top of a lawn edging stone - wont drill holes and screq in something). I did 3 versions, a shorer one with about 120mm for direct…
The original are not stable and break soon, so I created more stable. Focus to mount on 50x80mm square timber. I did two versions - up and across. I suggest to print like slicer-screenshot shows, tried 90 rotated flat on bed too, but then…
Replacement for lost axle. Bit hard to print because of the fine details in the center and the supports that are needed. Tree support seems to work better than normal, need a bit of expermiments whats fits best. I also tried upwards print…
Because my old posts get rotten slowly I decided to build a cap to protect them. The posts are 65mm square with head like to see in picture. So I designed them fitting. If you need another post size just scale in the sclizer to what you…
I did a simple way to just clip on a ESP32Cam board and put it on the z-axis on my Ender. The cam is fixed inside, so that you can easy use a focus tool (after preparation like remove sealing). Supports are neccessary and may be a bit…
Needed some replacements for old and broken contacts. I did a version for thinner and one for thicker cables. Only the hole on the top is different. Print in TPU. Did mine in 0.2mm layers which is good enought for the “grip section”.
Because I have some towels and other fabric stuff that do not have a loop on it to hang on normal hooks and thinks like that I created a version where you easy can put an edge into it and it stucks and stays. (the left and right…
It has a 4x2 pattern and (note) it has to be the topmost cup as you cannot stack one on top of it (otherwise I would have had to add 1 more height unit, which does not suit my needs). I need them very often, so they have to be at hand -…
Unfortunately, I couldn't find a suitable pressure bed plate holder for me, as the required number of places wasn't right for me, so I made my own, which can be extended again and again as required. There is a holder for M4 screw nuts on…
I built myself a funnel where I can put a kitchen towel in to filter and the liquid passes through well. With a normal filter, the kitchen towel sticks directly to the funnel wall due to the cohesion and there is hardly any flow. Here,…
Replacement of Playmobil carriage rear axle. Foto shows broken in front, printed (with one wheel already on) in back + mounted. Printed mine with 0.1mm layers because of small springs on the ends. Also a tiny bit of support is needed to…
fits for 20mm pipes with 40mm distance (2nd version with smaller hock added)
Because my calipers battery holder broke and without you cannot remove the battery anymore - bad design - I needed to create a copy of the broken one. I did a small bevel at the most inner end, for easier sliding over the battery contact.…
I found a cheap (12€) USB cam board with an OV9726 chip on a well known platform that has manual focus and a 50° view, so it seemed like a good way to take a look at what my nozzle was doing. To mount the board in my Ender 3 S1 I made…
Since the nozzles fell out at the slightest movement in the holder supplied, and there are only 2 places but 3 nozzles, I made this alternative holder to slide onto the station. Printed mine with 0.3mm Layer hight and recycled PETG from…
The sealring on my Luminarc glass storage series broke and its impossible to find replacement! So I created my own, printed with transparent Extrudr Flex-Medium TPU (98A) - FDA compliant. The original has 2 bigger lips, which is hard to…
Just did a new one. Print in TPU (only)
Since nearly empty toothpaste tubes always seem to tip over, I designed this holder to keep that from happening. It also happened to be a good spot for the interdental brushes.
These are all currently available results.
