Counting matching models…
Insert was designed for a 19mm diameter wedding band, but the print is flexible enough to adjust for other sizes. Printed in natural PETG and is virtually invisible on light skin tones. Supports are required.
The Prusa Enclosure temperature/hygrometer sensor (https://www.prusa3d.com/product/temperature-sensor/) is attached to the Core One via two 15x3 mm neodymium magnets. The sensor holder straddles the inside left push pin of the door frame…
Metal fork propeller pullers are difficult to use and results in the risk of broken or bent quadcopter components. This 3D print requires user to pull along the axis of the motor shaft, so no bending occurs. Device is pressed until hooks…
Raccoons can easily get into City of Toronto garbage and recycling bins and make a big mess. Two-step clip removal : this design require the user to 1) press on the mid-clip section with the thumb while 2) that hand's fingers rotate the…
Printed with screw hole vertical to prevent splitting when tightening the screw. Filament is PETG to handle creep and hot water lines. Screw hole has a small bump-out to retain the screw in preparation for installation.
Cage/basket keeps planted tulip and other flower bulbs safe from squirrels. Printed at 100% infill to avoid water infiltration followed by freeze expansion. The cage, hoop and retainers are assembled and placed in the ground. Add the lid…
Holder is intended for a single sheet, but additional sheets could be accommodated with diminished anti-rattle power. The design includes 7 recesses for 15x3 neodymium magnets. The two sheet-retention magnets could be secured with…
Metal fork propeller pullers are difficult to use and results in the risk of broken or bent quadcopter components. This 3D print requires user to pull along the axis of the motor shaft, so no bending occurs. One end of print is for CW and…
Blade was polished with 3000 grit sandpaper to minimize grounds sticking. Intentionally tight fit for the two parts. Plumbers teflon tape can be added to male thread to assist in assembly.
Organizer for key 3D printing tools such as 2.5mm Allen key, tweezers, side-cutter, needle nose plier, deburring tool, razor blade knife, flashlight and glue stick (sd card holder is no longer necessary). I have been using this organizer…
Designed for tongs that are approximately 220mm long and have arms that are 16mm wide. Belt is retained when arms are open. Printed with flex filament.
My wife takes Flamenco dance lessons via Zoom and needs the iPad camera image to include her feet. The tablet is propped on the fireplace mantle -- now with this 3D printed stand that allows the device to be inserted with various degrees…
Minor dripping developed on our Pixie that is more than 10 years old. This pad prevents coffee and hard water residue from forming on the countertop. The back feet of the Pixie should touch the back of the pad's crossbar. The small…
The Adafruit PyRuler (Engineer reference ruler with CircuitPython, product ID 4319) includes 4 capacitive touch sensors connected to an onboard Trinket M0 that can be used to trigger keyboard/keystroke sequences to a computer. I use the…
This button replaces the broken molded button on an old Ikea patio umbrella. Printed in PLA with a 0.2 layer height.
Printed with no support.
Perfect for alphabetic arrangement of lots of spice pouches (pouches that are 120mm wide by 130 high). Printed in PETG, but PLA would be just as good.
The ½ inch pex plumbing pipe is a friction fit into the 3D printed adapter. Adapter has suction bypass holes to minimize vacuum motor stall if pex pipe gets plugged. The suction tip of the pipe should also have a notch or hole to minimize…
Shelf undermount holder for 5 sleeves of Nespresso, When user pulls out selected sleeve, the remaining ones stay in place due to friction. Backstop print is optional to provide uniform protrusion of sleeves. Print Settings Printer Brand:…
Print orientation: on end.
This design requires flexible filament to permit strap installation into the cincher, i.e., the center posts are bent to work the strap into the device. Designed for a folded yoga strap that is 18mm wide and approx. 5mm thick. Optional:…
The interior of a self-built walk-in cooler is insulated with foamboard. This panel lifter is used to cinch vertical foam panels into the ceiling panels in preparation for wall screws. Printed on its side with no supports.
Designed for tablets that are approximately 19.6 x 4.6 mm. Insert tablet and press the hinged thumb piece. Print the splitter device on is narrow side. Supports are required.
Six 3x15mm neodymium magnets are imbedded into each cover (2 covers required for the entire light strip). Printed with PolyMaker CoPA Nylon (Natural color) to address elevated temperature above the stove. Note that these covers are being…
These are all currently available results.
