All models

multiboard glove holder remix

to attache to the multiboard you will need 2x https://www.printables.com/model/1074671-multiconnect-generic-connector-for-multiboard-v2

Toyota Land cruiser 80 series center console cup and phone holder

Remixed cup holder to allow space for a phone

Land cruiser 80 cup holder

80 Series Land Cruiser cupholder insert for center console

Parkside x12, Milwaukee, Bosch - 6 pack battery holder v3

Print with manual supports for the Handel. Handel is thicker now.

Gooloo GT 4000S rugged storage box

Storage/transport box for a Gooloo GT 4000S jump starter. Accessory fits under the Jump starter. Needs 6x M3x30 screws.

Portable monitor stand

To assemble you will also need M6 threaded rod and M6 Hex nuts To mount Monitors: https://www.printables.com/model/1120116-arzopa-z1fc-cover-and-multiboard-holder…

Arzopa Z1FC protective cover

Print standing upright and glue two half's together. Do a less messy glue job then I did. ;-) Orca slicer fuzzy skin settings use 0.3/0.3

Camping canister water pump faucet

Holder attaches a cheep battery powered water pump to any larger water canister with a DIN61 opening. e.g. 30l in my case. In addition to a water pump which can be bought on any major online market place, you will need some M6 hex bolts…

Parkside x12, Milwaukee, Bosch - 6 pack battery holder v2

Print with manual supports for the Handel. Handle is lower and wider. Improved v3 here: https://www.printables.com/model/1307074-parkside-x12-milwaukee-bosch-6-pack-battery-holder

Contersink depth stop

Contersinks single flute: 6mm shaft 8mm shaft 10mm shaft Bearings: 2x 6801 1x 6001 Heatset inserts: 4x M3 short 2x M4 Grub screws : 4x M3 2x M4 Part tolerances are for printing in ABS, might need adjustment for other materials.

Parkside x12, Milwaukee, Bosch - 6 pack battery holder

Print with manual supports for the Handel.

Parkside Band saw table stand

Table stand for a battery powered bandsaw from parkside. Printed in PETG, tabel and power hold down in ABS. You will need 4x M3 insert and 4x M3x8 countersunk screws. The saw is fixed in the tablestand with wedges, you will need to…

24 car fuses holder

Holder for 24 car blade fuses, remixed from original design fro thingiverse. For more details see original page.

Needle Tip Squeeze Bottle TPU cap

TPU cap for needel tip botels.

Remixed X20 6Ah or 3p5s battery extension

Extend the 2Ah to 6Ah battery. Glue the extension to the existing batteries, I used MS polymer glue. Other glue which can glue the print to PA should work fine. Mine are printed in ABS. Use a spot welder to connect the the new batteries…

Parkside x20 rivet gun accessory holder

Parkside battery powered pop rivet gun comes with attachments for different rivet sizes, but no option to store them on the rivet gun. Also it includes a compartment to store the replacement jaws in it. All you will need in addition is a…

Mac mini M4 portable monitor stand

To assemble you will also need M6 threaded rod and M6 Hex nuts For the assembly the power switch needs the cover plate glued on You can fit 2 SSDs as well, the adapters included are for:…

Arzopa Z1FC cover and multiboard holder

Print standing upright and glue two half's and holder together. Do a less messy glue job then I did. ;-) Orca slicer fuzzy skin settings use 0.3/0.3 to attache to the multiboard you will need 2x…

Flightcase lid profile

Flightcase profile to print. Print upright and use slicer to cut to custom length. Holes for 3mm pop-rivets.

Macbook pro 15 2015 headless mod

upcycel a macbook pro 15 2015 with broken display as a “desktop” computer.

3x Parkside X20 charger mod

Make you own 3x parkside X20 charger. The cover locks the chargers in place. You can reuse 4x of the rubber feet which come with the charger. Glue the 2 parts of the board and lid together. BOM 6xM3x16 socket head screws 6xM3 heat set…

Tesla P4 Fan Shroud mirrored fan mount

Mirrored it to offset the fan to the opposite side to fit my dell 7050. Uses 40mm fans, for fan grill lock at original.

Flightcase edge and corner profile

Flightcase profile to print. Edge profile print upright and use slicer to cut to custom length. Holes for 3mm pop-rivets.

Kimwipe multiboard holder

to attache to the multiboard you will need 2x https://www.printables.com/model/1074671-multiconnect-generic-connector-for-multiboard-v2

Airtag, Android Tag, Samsung Smarttag case for high power battery

Print lid and case in ABS or PETG. Seal should be printed in TPU. BOM: 4x M3 heatset inserts 4x M3x8 allen screws 2x Single AA battery holder or 1x AA 3v Holder 2x 14500/R14505 Li-SOCl2 3,6V Batteries or 2x 1.5v Lithium AA batteries Wire…

Plastik welder case

Storage case for a plasitc welder.

Flightcase lid latch

Uses 2x M3x40 screws to mount the latch. The lock uses a M5 screw and locking nut. Rivet holes are 3mm. Check out my other flightcase models.

Parkside air pump to exped synmat or other exped mats

Printed mine in TPU. Fits other exped mats aswell.

Monitor stand dual monitor arm

To assemble you will also need M6 threaded rod and M6 Hex nuts Base stand https://www.printables.com/model/1133828-portable-monitor-stand

Parkside x20 and x12 charger

Combine a parkside x12 and x20 charger. BOM 4xM3x16 socket head screws 4xM3 heat set inserts 1 Ziptie 2x 3x Wagoclamps 4x M4 nuts 4x M4x12 screws

Flightcase handel

Use M3 bolt and nut to mount the handle to its case. Rivet holes are for 3mm rivets. Check out my other Flightcase models.

Pizza peel wall mount

Allows to hang a pizza peel to the wall.

Parkside x20 die grinder accessory case

Keeps your accessories of you x20 die grinder in one place. Need 6x M3x30 screws.

Spice shelf

Needs 2 medium size command strips to mount.

USB PD trigger board TPU enclouser 12V

TPU enclosure for a USB PD trigger board labeling imprinted. Print in TPU, secure cable and board each with a zip tie.

Fairbairn-Sykes modern interpretation

Using a pre-made blade, design a modern interpretation of a Fairbarin Sykes knive. Knive tang is screwed in with a M5 nut and covered with a plug. Use slicer modifier for the grip to apply fuzzy skin. Print in a material which is not…

Parkside bandfile accessorie box

Box to store accessories and spare belts for a parkside x20 bandfile PBFA 20-Li A1 Needs 6x M3x30 screws.

Martindale No 227 machete sheath

Print pats in strong slicer profile and glue parts together.

Camping Lantern - let there be light

Enhanced Printable Model Description: This printable model provides a detailed and practical solution for constructing a portable, telescoping LED light mast. The components and materials required are as follows: Components and Materials:…

Parkside x12 battery charger 12V-32V powered

I was inspired by this video: For the X12, the converter board did not fit in the enclosure. Set the converter to 12.9V out. Weather you want to use the low voltage cut out depends on your use case. I set mine to 10V. Set the out put…

Acer MB16AP portable monitor protective cover

protective cover for the Acer MB16AP portable monitor

Wheel nut caps loosening indicator

Wheel nut caps to check if the nuts came loose. Printed with multi material system. Marker printed in glow in the dark. Also added tritium vials in addition secured with epoxy. Model fits 17mm heads, you can scale to outher sizes.

5.25 inch bay to pcie slot

Improved the lower card mount to be more stable and extended the sides so the rear mounting holes can be used.

hp zbook x2 g4 rugged transport box

hp zbook x2 g4 rugged transport box with TPU shock absorbers.

Acer MB16AP portable monitor protective cover and multiboard mount

Acer MB16AP portable monitor protective cover and multiboard mount

Haltec H-5265 air chuck dust cap

Dust cap for Haltec H-5265 tire valve quick connect air chucks. While airing up and down 4 tires at once, the caps reduce the risk of getting sand in the chuck locking mechanism. Rear part prevents sand to get in from the back, use…

Starlink 12v / 24v router and PoE cable holder v2

Print the 2 parts and glue the lap joint. This model does not house a starlink plug adapter as I have converted to normal RJ45 plugs. Board houses 12v>>48v and 24v>>48v PSUs. Also added a USB LTE stick.

Flor mat plugs

Makes the floor mats so no water or sand get trough on the car floor or carpet. Used some MS polymer glue, (e.g. patex extreme) to mount/seal.

Starlink dishy 2 flatmount for front runner roof rack

Flat mount with relatively low profile. Gets rid of the proprietary Starling plugs. Design uses IP 65 Ethernet plugs ( coupler and plug .) The base uses a 3mm polycarbonat sheet for the bottom. Hard ware is M3x20 and M3x16. Threads use…

Caming lantern dimmer case

Building a camping lantern, made this case for a PWM dimmer for it.

Camera neckount rugged case

needs 6x M3x30 screws

Uvex Sportstyle 232 P sun glasses case

Protective case for Uvex Sportstyle 232 P sun glasses

Tie down strap bumper

Bumper for the lock of 25mm /1" tie down straps. Print in TPU, needs 2 zip ties to mount.

RJ45 ethernet plug dummy IP65

replcacement dummy plug for IP65 ethernet receptical

Psion-Style Cyberdeck Shell for Sony Xperia XA2 Ultra

A compact clamshell shell that holds a Sony Xperia XA2 Ultra and a Bluetooth keyboard in a fixed, usable geometry. The design follows the Psion Series 5 idea of a screen sitting above the keys at a readable angle, with cues from modern…

Foam gun air pump holder

Attaches a battery powered air pump (oasser) manual foam gun (Alta foam 2000), allows 1 Handed use of foam gun and air pump / air compressor.

thuraya carmount external antena holder for roofrack

M6 screws to fix the clamping ring and 3x M8x30 to fix to the roof rack. Print shims to adjust play against the roofrack.

remixed tinyTouch - fingerprint unlock device for Mac

Read original design for more details and software and other configurations on github: https://github.com/zimengxiong/tinytouch

5.25 inch bay to pcie slot

Wanted a stronger lower support for a Nic.

starlink dishy 2 cutter

After scoring use a sturdy knife and a rubber to split the case of the dish in order to flat mount it.

Camping lantern step down up converter case

Camping lantern step up and down converter to drive a 12V COP, set mine to 14V.

Airtag clone card conversion

Convert cheep airtag clone to fit in your wallet. For the airtag clone see photo, no idea who is the company behind them. Besides de-soldering of the battery contacts you need to clip off the top of the button.

Roofrack DSLR mount for Panasonic GH2

Uses M8 hardware for mounting and 1/4" to attach the camera. Needs to be printed in a heat resistant materiel, did mine in ABS might work also in PETG. Dampers and dust cover need to be printed in TPU. Here an example Panasonic GH2 with a…

Dual ideal diode case

case for 2 "ideal" diode boards for reverse polarity protection.

USB PD trigger board TPU enclouser 20V

TPU enclosure for a USB PD trigger board labeling imprinted. Print in TPU, secure cable and board each with a zip tie.

Mini Grease Gun Filler

My attempt to make filling the mini grease gun less messy from a tub of grease. It takes about 3 "pumps" to fill the gun fully. Use the wiper rings to control the excessive grease. Print parts in petg and TPU. You need to glue the TPU tip…

USB PD trigger board TPU enclouser 15V

TPU enclosure for a USB PD trigger board labeling imprinted. Print in TPU, secure cable and board each with a zip tie.

USB PD trigger board TPU enclouser 9V

TPU enclosure for a USB PD trigger board labeling imprinted. Print in TPU, secure cable and board each with a zip tie.

USB PD trigger board TPU enclouser 5V

TPU enclosure for a USB PD trigger board labeling imprinted. Print in TPU, secure cable and board each with a zip tie.

Motorbike compressor (wind gallop)

Project: Slime Compressor Re-Housing Compatible Models: WindGallop light blue compressor Required Materials (BOM) Glue: B6000 or RTV Silicone Filter: Replacement filter foam Fasteners: 1x Zip-tie (small/medium) Original Parts: Compressor…

Fresh ’n Rebel Smartfinder (action) CR2477 Battery Extender 4y runtime

BOM 8mm wide nickel strip CR2477 battery printed parts Be careful not to short the battery with the nickel strips and align the positive contact. Screw in lid is left hand thread!

Painters triangel bar

Simelar to painters pyramide, if you need to prop up a small lip which would be hard to do with a pyramide.

Battery powered MIG welder

Portable Trail Welder (Karnage-Style) Trail welders are notoriously difficult to source in Europe. This project allows you to build a high-performance, battery-powered welder comparable to the US-made Karnage system. Powered by two…

Motorbike ultralight compressor (Slime)

Project: Slime Compressor Re-Housing Compatible Models: Slime Power Sport Compact Required Materials (BOM) Glue: B6000 or RTV Silicone Filter: Replacement filter foam Fasteners: 1x Zip-tie (small/medium) Original Parts: Compressor unit,…

Vlog in a box

Got the inspiration from this video: Stores: Smalrig Airplay monitor and remote trigger Magsafe camera tripod Ulanzi A100 wireless mics Magsafe powerbanks Eressa ES-D017 Ugreen PB561 Newmowa light SL-60AI Magsafe cold shoe adapter In…

Soda stream CO2 bottle cap

Soda stream CO2 bottle protective transport cap

American Optical ORIGINAL PILOT case

Protective case for American Optical ORIGINAL PILOT sun glasses, fits size L

Lenovo p520 3x GPU extension

Adds 3x GPUs to a Lenovo P520 workstation. You need 2x of the base models. Use glue to put the part together. I use 2x 20cm riser cards. Needs power splitter.

Parkside Battery Pump Air funnel & Nozzle added eyelet

3x Parkside X20 charger 4.5A 270W

Make you own 3x parkside X20 charger 4,5A 270W. The cover locks the chargers in place. You can reuse 4x of the rubber feet which come with the charger. Glue the 2 parts of the board and lid together. BOM 6xM3x16 socket head screws 6xM3…

Parkside air pump to exped synmat or other exped mats V2

Printed mine in TPU. Added Eyelet to the model. Fits other exped mats aswell.