Counting matching models…
Ultimulti MMU3 project is a DIY multi-material solution developped in parallel with the Original Prusa MMU3, with the ease of use and reliability being the two key improvement objectives, while still maintaining a reasonable…
The basic body shape was derived from the MURAT 124 model modified into the VAZ 2101, or as we know it by the export branding: Lada 1200. The classic vintage soviet ride.
Cut off the remains of the rubber part on your windshield cowl and attach these printed ones. OEM PART: 51718208483 Mirror the end part to use it on the other side. Print multiple mid parts to cover the entire length. Printed from…
___________________________________________ Make sure to also check out the MMU3 UltiMulti printable parts ___________________________________________ Chimney and Chimney-base parts are an alternative to the Prusa ir-sensor-holder-mmu2s…
ESP32-S3-EYE camera module cover. Mounts onto a 16mm ball hinge plumbus such as this one: https://www.printables.com/model/742987-rpi-camera-holder-plumbus Or onto various other RPi camera mounts , such as the Sneaks's Articulating RPi…
Camera holder for RPi camera to be used with Prusalink. Compatible with: - Prusa MK3/MK3S/MK3S+ printer - Raspberry Pi Zero W / 2 - 15cm RPi Zero CSI camera cable (Zero has a narrower connector than the larger RPis) - Raspberry Pi camera…
simple attachment for a camera Derived from MK3S+ PrusaLink camera holder: https://www.printables.com/model/424241-mk3s-prusalink-rpi-camera-holder Compatible with Sneaks's Articulating RPi Camera Mount and various other RPi camera mounts…
Compatible with MK3/S/+ printers utilizing the Einsy Rambo control board. rpi zero 2 frame: works with both the Zero W and the new Zero 2 with no risk of damaging the small components on the PCB. holds on the Zero: doesn't fall off works…
Works in combination with the cheapest available 2T hydraulic jack. One side of the pad copies the profile of the jack to fit perfectly. If the shape doesn't suit your particular jack, you might flatten it by cutting it off using the Cut…
This nut is suitable for i3 series printers or MMU2S. Pitch 2mm, lead 8mm Nut used on Prusa MINI is a different one. Tried printing it in PETG and it worked well after going back and forth with the threaded rod for a few times. Nylon…
A simple tool to help you 1. verify there are no print leftovers in the resin vat or stuck to the FEP foil. 2. filter out the possible chunks - sort of - without removing the vat from the printer. Just submerge the tool into the resin vat…
Starší, ale jednoduše tisknutelná verze krytu zadního světýlka na moped Stadion S11/S22. Sklíčko pasuje a drží bez dalšího spojovacího materiálu. Fotografie ilustrační.
Alternative xLCD cover with improved looks. Enables to reach the corner parts of the display more easily for better touchscreen experience. There were several xLCD versions shipped with the printers. Mainly, a bolt pattern differs. Check…
Protect your van against AdBlue thieves.
Printable jaws for 80mm lathe chuck
Prusa MK3S+ to Bůža Research MK3B Upgrade. Voted the most cool upgrade in the universe. Modified Einsy/Rambo case to acomodate larger screws for attaching the extruder and heatbed cable bundles. No more cracking. Cooler appearance.…
A new type of extruder gearbox: strain wave gear / harmonic drive. It sort of resembles the cycloidal drive in a way - but it's not the same as the principle of function differs. Fully printable; internal flex gear must be printed from a…
The tray (podstavec) gives your CW1 the same height as an SL1. Oh god! How this has always bothered my OCD! you can store mess in it. Spatulas, gloves, the funnel etc. you can either put the PSU inside or attach it onto the back side of…
A cover for Hormann garage door opener remote control, which had the bottom keyring part broken off. The other file is a dummy remote control unit.
A tool to help you align the T9 key when replacing a FEP foil on your SL1S resin tank. Other than that, the #1 advise for a painless FEP replacement is: get WERA 05028032001 TX8IP screwdriver. ____________ Printable on both MSLA and FDM.…
Spool holder - a total remix of the prusa enclosure fully printable one. I've re-mixed it so it can use the 6002 bearings I had plenty of lying around. And this is what came out from re-mixing it like 5 times more at least. One of the…
Rill upgrade for your BROR table. The block will be attached by two M6 screws and nuts to the prepared holes in the BROR legs. RILL wheel can be attached by four M4 screws then.
Replace a cracked lathe belt drive wheel with this 3D printed one. Printed using .25mm nozzle and PC-Blend material. _________ Opravné kolečko pohonu na stolní soustruh. T5 31 zubů.
universal angle guide: 15 ° 17.5 ° 20 ° 22.5 ° 20 ° can be attached onto a 6mm rod for convenient storage. Suitable for printing at low layer heights.
Calibration llama with USB drive / SD card / hex key holder. The RPi-extractor tool can act as a Calillama's wig.
The holder holds the two differently sized cups on the machine body. For Yaogong hot air station.
Use with M6 threaded rod or alternatively, the 3mm standoffs. Use M4 screw for the pivot
Replacement trays for Gorenje refridgerators Various sizes Two types of Egg holders Printable on Prusa XL
Re-use the old SL1 tank FEP foil by attaching it onto the CW1 platform with these little retainers. Cured prints are easier to remove. pick one of the versions and print 2X. Your CurWa will be easier to clean and won't become all glued up…
The final upgrade for the MK2. the firmware is not finished yet. need of a transistor logic inverter for the filament sensor to be used. You can do it in code, but the source code is quite painful to modify. need of a parallel Y cable…
Basically a spoolholder for CW1. The idea was: what if you could dry a filament inside the CW1? Unfortunately, the original firmware allows the heater with the fan to run just for short periods of time which doesn't make some moist…
These are all currently available results.
