257 models
This is a tool to correct the angle for a triple monitors setup for sim racing
Print approx. €0.39–€0.47 excl. taxPreliminary estimate for one variant
Modification of original for: better angles of camera adjustments (on both sides) camera can be fixed in about 180 degrees Adapter itself: massive on both sides - this is IMPORTANT against other adapters - not to be broken during…
Print approx. €0.56–€0.69 excl. taxPreliminary estimate for PETGSource material: PET
Dans la Pédagogie Montessori , Les triangles constructeurs bleus sont destinés à l’expérimentation sensorielle de la géométrie en 2-dimensions. Ce matériel se présente en une série de douze triangles rectangles identiques, dont les angles…
Print approx. €0.76–€0.92 excl. taxPreliminary estimate for one variant
Print Settings Rotate the model onto its side for layer strength. I used 15% triangular infill for my print, but if you need additional support increasing the infill should be fine. If all else fails, increase stand_thickness . Parameters…
Print approx. €6.59–€8.06 excl. taxPreliminary estimate for one variant
Print-in-place laptop stand by @Cherry_Labs. I modified hook height for my 16” Macbook Pro (2023) or laptops up to 14.29mm thick, including the rubber feet. Cherry Labs recommends printing with a 0.4mm nozzle. See his model page for…
Print approx. €4.56–€5.57 excl. taxPreliminary estimate for PETGSource material: PET
I used PLA, no brim (nor support).
Print approx. €0.07–€0.08 excl. taxPreliminary estimate for one variant
This is a canopy for the BetaFPV Air Tinywhoops, like the Air65 and Air75. The longer tail section allows a lower camera angle to be set. I also made a widening in the area of the right holder to additionally fix the antenna connector. I…
This phone holder is designed to hold your phone vertical or horizontally at three different angles: 60, 70 or 80 degrees. The holder comes in 2 different models, the lightweight or infilled model. The lightweight model prints on its side…
The angled mount hole centres suit a Ring doorbell generation 2 model with holes centres of 44mm (width) by 87mm (length). 2.0mm mounting hole may need opening up to suit non-OE screws Recommended lay height of 0.2mm (Speed) and 100%…
This is a remix of my popular Honeycomb Shelf Bracket ! I added a voronoi and a triangle pattern. The shelf bracket has the dimensions of 240 by 200mm. Take the long or short side up. You can also simply scale the shelf bracket. The holes…
A unique take on the laptop stand. It prints in place, with very sturdy hinges and is adjustable to multiple angles. Its primary usecase is raising the laptop off the table, while still being more than portable enough to always have…
✌ Angles Foldable Phone Stand. Suitable for smartphones and tablets! Features: Foldable Two different angles Print in place Portable Suitable for smartphones and tablets Perfect for travelling ✈ ;) Print Instructions: Layer Height: 0.2 mm…
Elegance and Protection for Your Frames
No more fiddling with resting your phone against random objects when bored on a flight of cafe after realizing you don't have a phone stand with you. Credit-card sized and ultra-thin to fit in any wallet. This version can hold the phone…
There are now two options to join the pieces: with glue (choose the files with the word glue ) or interlocking them (choose the files with the word click ). If you need to build a square box, print 8 Corners clamp for cargo straps glue 4…
Manipulatives representing different angles that can be used to measure, compare and combine angles. For primary school.
Someone in the comments mentioned that original canopy is too thin for TPU so I added 0.5mm thickness for it
Simple stackable painter's pyramids to print without supports. Most other I saw have circular holes on the sides, which are hard to print with no supports. This design has triangular holes for that reason.
Cellphone holder with 3 positions, I made it for looking up recipes while cooking. I'm not really good at 3D-modelling, so I designed it in Illustrator and used Fusion 360 to just extrude the surfaces 🤷♂ I also uploaded the .svg if you…
Squares See-Through Bowl - Vertically This 3D printable bowl features a unique geometric pattern of intersecting triangles, creating a mesmerizing see-through effect. When viewed from an angle, the intricate latticework reveals a…
Different sices of Humbucker Frames. If you want a specific sice: Just cut the 10.5 file in slicer
Unlike a common painting triangle, this design features a ball end to prevent the tip from digging into the plywood. Designed for use with large sheets of softwood. Screw holes are 4mm in diameter Printing with PLA is suggested (3 walls,…
My son got himself a RC Car and spent all day playing with it. Later he came to me and asked if I could build him a ramp so that he could do some jumps. I searched for existing ramps and found some who needed way more filament than what I…
the camera mount from the five33 whoop These mounts are designed and used by Team BlueEyes in the Italian Whoop League 30 deg 35 deg 37 deg 40 deg print settings: infill: 100% use tree supports fillament: tpu .2 layer also on thingiverse:…
Composition guide to look through when framing photos
It's a vase. My first vase design. Print it in vase mode. If you like check out my other designs too! Since the question came up recently, the license states that you may not use this model commercially. For me it's ok if you show the…
Increased base height to strengthen and made less deep to make getting parts in and out a little easier. Supports: No Resolution: 0.3 Infill: 20% Notes: Sliced in Cura w/ Horizontal Expansion = -0.3
I designed these feet to protect a wooden floor from the metal-pipe legs of a couple of chairs. With the exact angle of the legs, the base of the feet is flat on the floor, reducing the risk of damaging the floor. Update 2025-08-06: This…
A set of 12 small clay cutters perfect for creating ear rings or pendants from polymer clay, ceramic or porcelain. There are 6 different asymmetrical sizes (50, 40, 30, 25 and 20mm), as both a left and a right one. Best printed solid with…
A disk-like phone and tablet stand, that offers four fixed standing angles: 50°, 60°, 70° and 80°. A central finger trench supports swipe-up gestures, if needed. The stand supports different device thicknesses/sizes and keeps the centre…
Multiple Angles 40mm PVC (and others) Pipe Connectors. I designed them to make a Balls Pool for my sons but you can use them for several projects (Greenhouse, dog's house, etc.). You can easily adjust them to support different diameter…
Einfache Ohrringe mit einem Dreieck Muster
I stumbled upon a 3d model made by stigberg , printed it and showed to my colleague, a math teacher. She really liked them and wants to use them in classroom, but she pointed out that reflex angles are missing. In order to complete the…
I wanted to make 3D printed pen for a looong time. It consists of 8 blocks that are meant to be printed in different combinations of colors :) Happy printing.
Welcome to the world of Printing on Fabric!!! Its really simple! Just Follow these steps: Print 2-3 Layers Hit Pause Place the Tulle fabric Mount it with tape flat on top the printed parts Resume the Print When you use Simplyfied3D you…
(DE) Set von einfachen, stabilen 90° Winkeln. Bohrungen mit Kegelsenkungen. Versteifungsrippe in der Winkelecke. Vielfacher Verwendungszweck. Schnell und leicht zu drucken. (EN) Set of simple, sturdy 90° angles. Countersunk holes.…
Place all of the nine triangles in a square cutoff. Puzzles For Both Adults And Kids - not so difficult. Enjoy! Print instructions Print from two colors. The gcode of the base frame part has included colorchange.
Printed with pla, with layers of 0.1mm The purpose is to have a guide to avoid tangles and to secure the filament in the spool when not in use. Basically, it replaces the piece of cardboard that comes in the spool with the extra function…
Are you also trying very hard to achieve perfect cuts with a hand saw? I give up for now. That's why i created this jig. It provides 45° and 90° (which to be honest is sufficient for 99% of all our projects). There is space for 2 magnets…
To attatch Nanoleaf Shapes Trianglles with screws. After the Nanoleaf Support stated I should use a ruler to make drill holes for the Triangles I construct this drill template. Print with support! Printer: Artillery Sidewinder X1…
.3mf Ready to Print by TIXEN No supports required Sizes : 10°, 15° and 20° Please, Print it! Share it! and let me know about any suggestion or any issues Contact info: Email: [email protected] IG: @tixen.ar This work is licensed under a…
Few mounts compatible with other DeckMate system for Steam Deck printable parts that I thought could be useful. Double vertical “case” attachment Double vertical “case” attachment with backing 3 self adhesive, print in place universal…
This model work only with the OLD version of ReFill. If you have recently purchased ReFill products with the cardboard core, please download the updated flanges HERE ReFill is manufactured for usage with re-usable master spools like in…
Several versions of the Penrose Triangle illusion designed to be specially easy to print. I provide many examples and the OpenScad script used to make them. The Penrose Cubes variant is a classic optical illusion. Under the right light…
Angled Fan Mount for PC Fans (120/140 mm) This mount allows you to install fans at an angle inside your PC case. To use multiple fans, simply print additional copies and place them side by side. This lets you direct airflow precisely to…
Ran @andyroo770's model through Prussa "Simplify Model" and repaired with Netfabb
Another Audioengine A2+ Speaker Stand. This one features options for multiple angles for optimal listening experience. Print on the side for a nicer surface. Includes insets on the bottom for anti-slip rubber feet with a diameter of 10mm.
A simple but effective Corner Miter guide and Right Angle bars for alignment of your material when cutting/folding/marking book covers/pages etc. Works great with PLA. Complete your setup and organization with the models listed within my…
A desktop model to demonstrate the Euler angles typically used in aviation (roll/pitch/yaw). For the pins: You need to print 4 of them. The 18mm length is correct for two pins, but you'll need to stretch it vertically for mounting the…
Quick and easy earrings, you can resize as you like. Nozzle 0.4 layer 0.2
needed small drafting triangles to use in a spiral notebook that would also fit in a folder pocket
Sure, you could just go out and buy a few hundred of these with the change that you have hiding in your sock drawer, but wheres the fun in doing things the easy way? Parametric design lets you choose the height, thickness of the legs, and…
Remix of the MMU3-Holder to hang in in various angles
This model is compatible with the lego system.
Squares See-Through Bowl - Vertically This 3D printable bowl features a unique geometric pattern of intersecting triangles, creating a mesmerizing see-through effect. When viewed from above, the intricate latticework reveals a captivating…
Simple tool, easy to print.
I downloaded and printed a bunch of Nates' triangles https://www.printables.com/model/109169-painters-triangle-pyramid But I didn't have a holder, so I made one. Holds 8 of the triangles. Free my models a3b1b5fd
I wanted a set of painting triangles that all worked together. I also wanted to have a holder so that they could stay organized. The holder I designed it so that the triangles would all fit, but would be accessible. Also on the holder I…
Super simple to print and to use, these 45-45° and 30-60° right triangles are very useful for small scale 90° alignment checks, such as when gluing together parts of a model plane. In particular, I was constructing an FT Tiny Tutor kit,…
This is a MeshUp of two models to create a GoPro 11 Mini Mount for the TBS Source One v5 frame. I have added multiple angles If you prefere so. Angles added are If you need anothere please send me a Message and I'll add it 0Deg 5Deg 10Deg…
These are for calibrating the horizontal expansion setting for your slicer. I recommend to use standart cure settings for 0.2mm layer height, 215/55 PLA. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No…
Boucles d’oreilles en forme de triangle
Upgraded version of my favorite canopy with added rigidity and a second antenna hole for lower angles. You can print this from D40-D50 TPU , and it should be great and indestructible.
Remixed this great looking choc keycap set to make it match more aggressive angled keycaps. The following changes have been made: Deeper Homing Key icon so it's more perceptible. All angles increased to 15 degrees for easier reach and…
I printed in multi-color for high contrast and glued them together with Testor's Glue,
Hex Grip Print Bed Scraper – 2 Versions (Standard & Steep) A sturdy, ergonomic 3D printer bed scraper, designed with a modern hexagon-patterned handle for improved grip and style. Includes two models: Standard scraper and a Steeper…
This is a tool, that helps you sharpen a chisle with a very consistant angle. The angle can be chosen, by how far forward you put the chisle in the tool. All print files can be printed with PLA, but I advise you to print the “wheels” with…
The gap for laptop is 16mm, which will fit most of the modern non-gaming laptops Optionally but recommended for nice finish is M3 bolts to tight the bar. Ideally - with allen key head. But bars can also be glued in Designed to be printed…
Simple rectangle shape I use to calibrate flow, ironing, different infills
Printing Printed in Black PETG (spray painted with black outdoor paint to further limit UV exposure and to seal any potential gaps) at the following settings: Gyroid infill of 50%, 8 bottom layers, 0.2 layer height, 5 perimeters, 8 top…
A simple angle jig for 15, 22.5, 30, 36, 45, 54 and 67.5 degree angles. I use them to make inserts into 60 and 108 degree corners for my icosaeder and dodecaeder lamps. The other angles are used in Asanoha Kumiko. I printed it with 15%…
Printed out of PLA and TPU. PLA allows some flex to remove ice from tray It is designed to be printed face down with no supports. I printed with 20% infill for both PLA and TPU. Turn retractions and z lift off, and combing on for TPU with…
These simple 2 color geometric triangles are the modern decoration you didn't know you needed. These prints are quick and thin, as they are decorative items. With a bottom layer (white) at 1.5mm height, and line art (black) being 1mm…
This cellphone holder allow you to rest your phone in multiple angles as required. Perfect to put in your office desk!! #### 17/Jul/2023 #### added a plain version without symbols and letters to better print
0.2 layer height 2 walls 10% infill This remix is of the model shown in this YouTube video on how to help eliminate VFA and banding problems. Works with X1C, P1S and P1P.
This variation is exactly the same size as a standard 80mm fan to appear flush when mounted directly to fan. Low profile
Bonjour, Hello, FR : Les perforations rectangulaires du modèle original ne me convenaient pas : trop petit rectangle, la plupart étant bouchés par les ponts s'écroulant. Je remercie le créateur d'avoir fournis la version F3d de son modèle…
You can put the triangle model next to the problem and rotate it in any way to fit the problem, thanks to this you can understand which side and how you can count. Print Settings Resolution: 0.2mm Infill: 0% Filament: PLA/PLA+/PET-G/ -…
Designed to make an easily replaceable sprinker head for a ½" NPT riser or PVC fitting. It doesn't atomize, so there's minimal loss to evaporation, but this also makes it short range and more suited to gardens than lawns. If there's a…
English : Here is a tool that will help you form angles, edges and curves without damaging the fabric. Francais : Voici un outil qui vas vous aider à former les angles, bords et arrondis sans endommager le tissu. Print Settings Printer…
I needed the simplest and cheapest to print phone stand that I could use to watch Youtube. This stand offers 2 angles of the phone accordind to the height your eyes are. If the phone it is very low respective to your eyes you should use…
11/17/2025 - I didn't like the angle of the original mount that I made, so I made a few different variations to try them out and see which worked best. Figured others might like some different options as well. This is a gun barrel rest…
This remix of the Spotter Flag Simracing 8x8 LED Matrix features a redesigned mount with forward tilt options of 10°, 15° and 20°. Both versions include M6 and M8 mounting holes, allowing flexible installation on your sim rig. Perfect if…
A collection of angle corners and caps for 12mm x 9mm self adhesive trunking. They are designed to clip over the trunking and allow the self adhesive strip on the back to show through the covers. I made these as I could not find any off…
Should print perfect with just a few strands to snip at the end. Is there a limit to the number of terraces I can make in vase mode? Apparently not.
I just rounded some corners, nothing fancy ;) The original can be found at https://cults3d.com/de/modell-3d/haus/box-for-din-a6-paper
This mount is designed for the Foxeer Cat 3 Micro camera (19mm x 19mm), providing stable, fixed-angle mounts at 15°, 20°, and 25°. It fits hexagonal rods with a width of 5mm, a center-to-center distance of 24mm, and a height of 20mm.…
Quick and dirty support with 2 positions. Modeled on Onshape I added the step file for easier remixing.
I needed a shorter version of the “Prusa Mini” angles. The original variants are 7 cells horizontal and 6 cells vertical. My versions are 5 cells (H) by 6 cells (V).…
I tried to use the angles90 grips but the straps dug into my hands. The grip was too small. I made this model longer and a little thicker for ergonomic reasons. You can print this out of any material, but I printed in PLA, with snug…
仿某款笔记本散热支架，有两个角度，打印简单使用方便，使用3M双面胶贴在笔记本电脑背面对称位置即可，使用4颗杯头内六角M2*15螺丝组装； Imitation of a laptop cooling bracket, there are two angles, easy to print and easy to use, use 3M double-sided tape to stick it on the back of the laptop in a…
A 3d printable light triangle similar to nanoleaf and corsair
The part mounting to camera needs only printing once, and the angled pieces are all compatible with it. Screw holes are same distance as the original mouting plate, so you dont need to drill again. If you need it to be angled to the…
This 3d model is a remix of a other phone case, i would recomend TPU or other soft plastics, you can also use PLA and things like that.
I needed something to organize some 95mm sanding triangles used by a Ryobi multi-tool. This one can also hold the smaller 80mm triangles. Used a 80mm design as inspiration and designed a larger one in FreeCAD.
Fits into Core One. Mount holes for 120 and 140 Fans in the center of the shelf
A wall mount for the Aqara G5 pro camera. 2 versions 25 degree and 35 degree. I printed in white PETG, with the wall contact side down, and with supports for the camera mount. 6 wall loops, 25% 3D honeycomb infill. Hope this is useful to…
