HP NC552SFP Dual Port 10Gbps SFP+ Card Low Profile Bracket
Printed with ERYONE PLA 180°C With support PRUSA i3 MKS+
Print approx. €0.39–€0.48 excl. taxPreliminary estimate for one variant
- Downloads
- 76
- Likes
- 6
- Rating
- 0
29 models
Printed with ERYONE PLA 180°C With support PRUSA i3 MKS+
Print approx. €0.39–€0.48 excl. taxPreliminary estimate for one variant
Modelled from the broken comb of my HC5356 but according to ebay listings it fits following models: HC5150 HC5350 HC5355 HC5356 HC5550 HC575 Can't say it's a 100% perfect fit but it's more than good enough and is fully functional and much…
Hier gibt es einen Einsatz der genau in den SQ14 Rahmen von einer Janome MC550E und kombatiblen Modellen von zum Beispiel Elna passt. Der Stoff wird mit einer Klemmplatte gehalten und nicht überdehnt. In Ober und Unterplatte sind Magnete…
This is specifically for the TOUGHBUILT C550, C600, C650, C700 sawhorses. Držiak pre stavebné kozy TOUGHBUILT C550, C600, C650, C700. TOUGHBUILT C550 TOUGHBUILT C600 TOUGHBUILT C650 TOUGHBUILT C700
a plain version without text, confirmed fits for the TS55 REBQ and TSC55 KEB.
holder for the Panasonic charger
a gridfinity holder (2x4) for a Panasonic BQ-CC55 charger (eneloop) and 10 AA and 10 AAA batteries
This is the sliding flap between Freezer-Fridge compartments that the appliance uses to let cool air in from freezer to fridge using small servo motor and thus control the temperature. The original part has weak spot in the "8-shaped…
We wanted to use our Apeman C550 dashcam in our new car, so I designed this holder for it. I used thick 3M double sided tape to mount it in the car. Dont use PLA: it will deform in the sunlight. ABS works fine. Support is needed! 2025-09:…
Absolutely awesome work from MartinRowan . I wanted to put my fiber optic modem on a sled. Used the provided blank sled .step file and made this sled. I'm including the first iteration I made and the final iteration. Initial: Full sled,…
Skadis mount for Panasonic BQ-CC55. The original model did not have Skadis hooks so I did this remix. Print with “strong” profile 0.2 mm and use supports on build plate only. Enjoy!
Asus Zenphone max protective cover, can be done with pla or tpu 1 version is with a card slot in the back (card can not be removed from the cover without first removing the phone) 2 version is just the cover. I prefer to print it with 10%…
May 2024: Wow, 6 years of heavy use and one of the PLA-printed rails finally broke... That's quite a durability. I'm reprinting it right now :D Dec 2018: This is a replacement drawer rail for Whirlpool fridge with ice maker - "american…
There is a left- and a right-handed version of the L shape. Reportedly works with Australian version too MakerWorld | Printables
These are ear cup cushion rings for Sennheiser PXC550 and PXC550-II headphones. They allow aftermarket ear cushions such as Brainwavz to be installed without the ned to cut up old cushions. Print the ring with the thin inner edge down as…
My Son learned to open our Abus Door lock. So i needed a lock... for my lock. So i´ve design a Kids Safe 2 Part Puzzle, that my Kiddo doesn´t know to open. Additionaly i added a press fit for the Second part, that makes it harder to open…
This handle extension allows for an upright posture while pulling the compressor behind you. The handle was printed with PETG and consists of four parts that are joined together using M4 screws and nuts.
Printable with PLA and PETG (the print in the photo was made with PETG). Settings: Infill density was set to 5% and the infill pattern to honeycomb; otherwise, the print was made with standard settings. I achieved a significantly better…
I created easy cover for LED indicator on router ASUS DSL-AC55U, because 2 leds cant off and his blinking is bad for my mental equanimity in night…
I have a Belkin F6C550-AVR sitting on a wheeled cart. The UPS can fall over sideways sometimes. This is designed to fit the feet of the UPS and has sides to prevent the UPS from tipping over when moved quickly. This was printed in PETG…
ABB Basic55 is one of the most common outlet series in Estonia and probably in the rest of the EU. But they don't make 2x2 frames for some reason. I drew in the frame and highlight. It is compatible with normal ABB Basic series sockets…
Based on the Gridfinity system by Zack Freedman (MIT license). Box generated using gridfinitygenerator.com , then modified to hold a Panasonic BQ-CC55 Eneloop battery charger on its side.
This design is optimized to be printed on any type of domestic resin or filament printer, so you can protect your mobile cameras.
This is a simple remix of Dylan's Gridfinity Panasonic Eneloop BQ-CC55 UK charger adapted for the EU Plug
This is the handle used to open the flap behind which the filter bag is located. A simple 3 mm rod is required as a shaft for installation.
We wanted to use our Apeman C550 dashcam in our new car, so I designed this holder for it. I used thick 3M double sided tape to mount it in the car. Dont use PLA: it will deform in the sunlight. ABS works fine. Support is needed! 2025-09:…
Hier gibt es einen Einsatz der genau in den SQ14 Rahmen von einer Janome MC550E und kombatiblen Modellen von zum Beispiel Elna passt. Der Stoff wird mit einer Klemmplatte gehalten und nicht überdehnt. In Ober und Unterplatte sind Magnete…
These are grip files based on the later style contoured grip that came on the Feinwerkbau C55P. This is designed for the C20 Pistol, but should also work on the Feinwerkbau (FWB) C25, C55, P30, P55 and 102. The grips are designed to reuse…