335 models
Recomended to print with PET-G, ABS or any car temperature resistant material. You will need to buy 50 mm wide velcro. To atach the velcro to 3d printed holder i used MAMUT glue (one-component adhesive with high adhesion) but i think you…
Has your Dummy 13 been “Chalk Lined”? Too weak in the knees to even stand up? After printing your Dummy 13 or other articulated model, you may have a loss in stiffness of the model when the 3D printed joints wear or stretch. This can…
Prints flat without any supports . You can use it to lay down the perimeter wire for your automatic lawn mower. You can also use it to lay down any cable you want this way. I used it for a 12V wiring for my garden lights. The grass will…
Plant fastening / fixing clips - Pflanzen Befestigungsclips 30mm / 40mm variants
NEM 380, “Fixing Elements for Containers and Interchangeable Superstructures” is a standard developed by MOROP, the European Association of Model Railroaders and Railroad Friends ( https://www.morop.org/ ). The standard describes how…
After the conversion of the Einsy into the Big Einsy Case, the cable routing to the bottom was unfavorable.
I have added some reinforcements to the 3D model because in the first impression they were broken when removing the support. After printing this version, now with these reinforcing ribs it gives greater solidity. Speed - 60% Infill - 15%…
The corner is made of PLA or PET-G filament. Angle dimensions: width: 40 mm Height: 20 mm wall thickness: 4 mm Infill: 20%
Easy to print ground Fixing Pegs
Print instructions: Layer height: 0.2 (0.2 QUALITY Prusa Slicer Profile) Infill: 80% for better stability Perimeter: 4 Support with amplifier (included in 3mf)
When handling prints, maintaining or adjusting the 3D printer placed in the Original Prusa Enclosure, the Enclosure door must be open. Quite often the door moves by itself to a position that is undesirable. Using a set of these 3D models…
Winkelhalterungen für 90 ° + 135 ° für IKEA-LED-Streifen 24 Volt (403,596,95), 13 mm
The LED strips fitted to the underside of the upper LACK table use double sided tape. I was concerned that temperature may soften the glue the the lights then fall. So I designed these clips to secure the LED strip and a pClip for the…
Does your bathtub and shower faucet also require a manual switching between bathtub faucet and shower head each time, you turn off the water, especially when you have shampoo in your eyes? Well, ours did and it annoyed me. So I designed…
Hook nails for fixing boundary wire of robotic lawnmover - in my case Husquarna Automower 305
This is a simple type of mirrow wall mounting clip. Perfect for standard 4.5mm mirror/glas thickness. Please feel free to leave a coment if you wish to request to remodel it for a differenct glass thickness.
EN: Bracket for fixing the PTFE bowden cable to the Prusa i3 frame This holder helps guide the string so that the PTFE tube does not pinch between the extruder and the frame. The model was inspired by the PTFE tube guide on the MMU2 unit.…
Bracket to attach the Home Station of an iRobot Roomba 981 to a wall, with space for a baseboard. Klammer um die Home Station von einem iRobot Roomba 981 an einer Wand zu befestigen, mit Abstand für eine Fußleiste. Print instructions No…
It fits over the original rubber holder and prevents a dropping of the sun visor in case of a worn out rubber mount. It can easily be mounted and so there is no risk of braking the glass during remove of the rivets. Just put it over the…
Replacement for knobs that are used for fixating the rubberbands of covers for trailers. Print instructions Print it upside down and use supports only on the bottom side. The contact surface of the supports will end up under the screw. I…
So I did this quick model to fit a 4mm square tube to a Stickybones Fly Rig socket and be able to use a normal winder. Printed in PETG vertically with the base towards the plate. No special settings, the fit will be super tight so be sure…
Français : Kit de fixation de plinthe pour Lave-vaisselle ; basé sur pièce 00612653 - compatible BOSCH, NEFF, GAGGENAU, BALAY, SIEMENS. Version raccourcie et simplifiée : permet de fixer de manière réversible une plinthe découpée dans un…
This part usually comes with the purchased product. But it wears out over time. So I remade this piece based on my need. I wanted to share it because I thought it would be useful to you.I Also share the photo of the original piece.. Stay…
A remix of the original with support for fixing the stands to a wood desk using 5mm screws sat flush diagonally.
Ditch the overflowing jewelry boxes and tangled rings! This stunning 3D printed jewelry tree offers a stylish and functional way to organize your collection. Crafted using eco-friendly 3D printing technology, the design features a…
T-Slot Nut M3 / M4 / M5 / M6 Thread / Twist in fixing nut for PRUSA Alu Profile -Update 24/01/2025: added Tslot Fixing Nut Prusa Alu Profile.stl Scale/Resize to adjust dimensions All our designs are free to download and use—because…
Sovol SV06 Plus is a great printer, but its bed heating cables are not fixed resulting a safety issue. With this solution first 20mm will be fixed. Don't forget to print it from ABS or other hi-temp material. Installation requires 10…
2024/06/12 Update: Added the piece that allows the camera to be attached directly to the X axis motor. To place the camera, in addition to the box that protects it (capuchonSuperior and capuchonInferior), It will be necessary to use the…
For my aquarium, I needed a hose holder. The tube was constantly falling and I was making a flood. I couldn't find what I needed so I took a few other pieces and cut and put them together. I use petg plastic and standard settings. The…
Print instructions Print settings: 0.20mm QUALITY Filament: PLA 20% Grid infill 4 perimeters 5 solid layers top and bottom If you require a different model or size, please do not hesitate to contact me.
Base to securely hold an Airtag within luggage interior. Foam tape to hold base. Cover plates slide and clip onto the base to hold the Airtag in place - intent is to keep the antenna as close to case exterior as possible. Printed PLA…
TETRAHEDRAL MOUNTING BRACKET - STAFFA TETRAEDRICA Flexible Fixing Grid (Up to 9 Points) | Filament-Optimized Design --- ## 📐 Product Overview - Dimensions: 60mm x 60mm (Base) - Mounting Points: Grid design with up to 9 available fixing…
Hello, This accessory prevents the sheets from coming loose, and the tabs keep them securely in place. It's sturdier than the basic model and not as high. the supports are already in the model Thank you for your feedback.
Building instructions in separate PDF. Note: See the following page for a printable fixing plate with real NEM 380 pins: https://www.printables.com/model/1180883-nem-380-container-fixing-plates-in-h0-scale-187
You can print in any colour you want. Example was printed in PLA+, 1.33 g, ~6 minute to print on V3 KE. Use the two M3 screws that came with the printer original clip.
Remixed it with 2 and 3 ribs to have it firmer for heavy load, so I can use less of them. Print it with the holes on the plate (like the original one). Print settings Material: PETG (or any other material that can handle the load).…
Description This assembly allows you to fix objects to the wall by turning them a quarter turn. To do this, you need to fit the 2 pieces together and make a quarter turn until you come to a stop. I used this principle to attach the shell…
Hello. My proposal for creating battery packs for the size 21700 Print quality 0.2 Material: PLA , PLA + , PETG , Infill according to your reasonin
Packout rail wheel bracket Bracket will fix to packout rail and hold the spinning wheel Printed in PETG 60% infill adaptive cubic 0.42 layer height Printing Remember to mirror the second part Add pause to layer where the hexagon space for…
Držák adaptéru Sonoff Zigbee 3.0. Pro připevnění na polici nebo na zeď pomocí dvou šroubů. Adaptér je zajištěn v držáku zasunutým USB konektorem a našroubovanou anténou na druhé straně. Tiskárna: Longer LK5Pro Materiál: PETG, C-Tech,…
Bei meinem Elegoo Centauri Carbon habe ich ein deutlich sichtbares 2-mm-Wellenmuster festgestellt, verursacht durch die glatten Umlenkrollen der XY-Gantry . Der GT2-Riemen rutscht dort über die Rollen, und das wiederholt sich als Ripple…
Diffrent fixing mechanism for 3 storry 1:64 HotWheels lift. I chopped off the little cips that were finicky to print and never worked well for me. Insted the part now just fits into the poles with friction. It fiits quite well. I don;t…
Hello. My proposal for creating battery packs for the size 18650 Print quality 0.2 Material: PLA , PLA + , PETG , ASA Support as needed Infill according to your reasonin
Einfache Wand- oder Paneelbefestigung, passt auf jede Schraubengröße unter 5,5 mm Durchmesser. Drucken ohne Stützen. Simple wall or panel fixing, will fit any screw size under 5.5mm diameter. Print without supports.
Ever had trouble with warped plywood on your laser cutter? You're not alone. I've designed a neat little tool to help : a Fixing Pin for your cutter's honeycomb plate. It keeps your plywood flat, so you can get those perfect cuts every…
Done for myself, but maybe someone will find this helpful as well. Story is simple. As I wanted to put my printed winder on plank, I found that somehow main body doesn't have a screw holes or anything else to fix it on surface (donor body…
These fit into my 2003 Toyota Celica trunk and hold up the "package tray". Passenger's side is provided. Flip to get the driver's side. Toyota Celica 2000-2005 Parcel Shelf Black Fixing Blocks / Package Tray Clips 64323-10040-CO Print…
print orientation as it comes from the STL, ASA or ABS recommend for temperature stability
This is a tool used when installing or replacing the shift cable for Shimano Alfine internal geared hubs.
2020 Fixing Clip Twist_In - Clip di fissaggio per profilo 2020 No thread M4 M5 Suitable for: https://www.printables.com/model/767250-extruded-aluminum-2020-profile-4-sides-open…
When you are building an IKEA Pax wardrobe, you should fix it to the wall. IKEA provides brackets for that, but if you have a skirting board and cannot push the wardrobe to be flush with the wall, you need a spacer. This is one. If you…
Modification: Fixing the device to the board Led diffuser for BT LED version
It is easy and support free to print. Set the infill to 20% minimum.
Spacer for fixing corrugated metal roofing sheet - Distanziatore per posa tetti in lamiera ondulata Dimensions 40x23(+10)x17mm Cap-Washer Resize to adjust dimensionIf you download/enjoyed this file, please leave a like - Thks Category:…
This is my take on a concealed toilet seat fixing, made due to the original falling apart before it was properly fitted. I hope others may find it useful. The bolt is a 5mm and the nut size is 8mm across, it should be a easy press fit. I…
This is a customizable hook or eye fixing that can be attached to the bars of your pet’s cage, so you can hang toys, hammocks etc from the inside. Obviously, cages are already pretty good for hanging stuff on, however, these fixing clips…
These are a small brackets which ensure that you can fix the broken Toyota Prius 2 tailgate with some new screw/nut and with some minimal glue. Unfortunetly I made it a two years ago, so I don't know how long screw and what kind of nut…
Filament fixing tool for sovol sv08 filament holder
I struggled to insert the end pieces on v2.0. I remixed it to increase the tolerance on my printer. I run a 0.6mm nozzle but did print at 0.2mm as directed. I've simply opened up the tolerances for the two tongue parts. Please get the end…
A hanging PET bottle organizer/dispenser that can be affixed to the bottom of any shelf or cabinet. Perfect to organize your pantry. Adapted from the Ikea Kallax version (which doesn't require any screws):…
Acknowledgements: This item is totally inspired by the splendid efforts of MXRR (see box below). Those items worked perfectly well - but I have big fat fingers and found them very fiddly! Design: I modified the OpenSCAD code for my M3 nut…
3D PRINT SETTINGS Wall Loops: 3 Layer Height: 0.2mm No Supports Infill: doesn't matter really
A 3D-printable dowel for fastening lightweight objects with screws to external thermal insulation systems such as EPS or Styrofoam façade insulation. Compared with similar insulation dowels, this version uses slightly steeper threads.…
A simple fixing element for the trunk of the car. Prevents boxes or other objects from moving spontaneously during the journey and thus unintentional damage. For fixing, a self-adhesive Velcro with a width of 20mm and a length of approx.…
I included two types with the logo: embedded (print face-down and let the filament bridge the cavity) and embossed (print face up, with supports, allowing a filament color transition for the top layers of the logo). The Lotus logo is…
2020 Profile HEX T-slot Twist-In Fixing Support M4-M5 Thread 2020 Profilo Supporto esagonale di fissaggio Twist-in M4-M5 Filetto Suitable for: https://www.printables.com/it/model/767250-profile-2020-alu-4-sides-open-adjust-the-z-scale-t…
3030 Foot Cap - Low Type - with predisposition for fixing with screws Resize to adjust dimension If you download/enjoyed this file, please leave a like - Thx Suitable for:…
A neat and stylish hidden fixing floating shelf Designed to use the same bracket as my PC/Controller stand (see other listings) so you can mix n match and re-use the fixings as needed. 120mm width, perfect for a couple of small trinkets…
All you need to bring back your C64 breadbin case in a neet conditions
Xiaomi Mi 360° Home Security Camera Fixing pad
The DeckBro is a Steam Deck accessory that makes it easy and portable for hard drives to be connected. It’s got two storage compartments: one for any hard drive of the 2.5-inch form factor or less, and one for a USB-C hub. They’re…
A simple print to allow the use of a 40mm radial fan with a Satsana cooling duct instead of the stock blower. (Eg a fan that is quieter than the stock blower fan) It uses the stock mounting screws and can be retrofitted to existing…
Supports et fixations de câbles renforcé pour tondeuse a gazon Alpina, Mac allister, Jardipro, Sterwins, Stiga. Compatible avec appareils Bl440sb (2016) [299264624/a15], 460bsp450-3 (2014), A410b (2011), Mlmp148b&s (2012), Jp55b4zm…
Replacement for FIAMMA No. 98673S204 + 98673A205 Settings: - PETG - 70% infill, Gyroid
It's best to print it from TPU/TPE, but the design will also work with PETG. Use <0.25mm layer height and max. 0.6mm nozzle when printing with PETG. No support needed. Prints in 10-15min. Improved the knob - no support needed anymore.
Simple but handy. You can heat it after print and bend it to your needs. Print instructions Even PLA is flexible enough. Still, PETG is recommended.
This is a cable fixing plate to install on the X linear module of Snapmaker 2.0 250/350 series.
bracket can be printed without any supports, has to be placed on chamfer printed in PLA, used 5 walls and 10% infill
This is for the 10mm to 8 mm XY Joiner. I have included step files for the parts if you require to create a 8mm to 8mm derivative. My stock XY Joiners on my Hypercube Evo build started to split under the tension of the drive belts and the…
Since this part is near the bed and the heat can cause it to change shape over time I decided to modify the original model with stronger pins preferable print with PETG or another filament that can tolerate higher temperatures layer…
A small clip that can be used to fix the top of the “AD5M minimal enclosure” variants, that has a small recess. The reason for this model is, that the magnetic fixing does not work reliably for me. Simply print 4 of the clips and replace…
Pipe Clip fixing for pipes and conduits Ø 16 / 20 - Fascette di fissaggio per canaline e corrugato For quick installation of: RNC conduits Flexible & rigid tubing No screw needed Drill hole Ø7 / 8mm insert and fixes pipes and lines…
trying to make Lerdge iX fixing belt unbreakable Recommendations Print in PETG uses more than 5 layer perimeters I used a) 1 M5 10mm screw and nut b) 2 M3 25mm C) 2 M3 10mm d) 2 M3 6mm coupling nut (optional) if you don't use this nut…
Spiderbeam ground fixing point for 10 meter spiderbeam fiberglass pole. Three ankerpoints for tent pegs. Bottom of pole (cap) fits into it.
This is a mounting plate to attach a genuine citroen / peugeot mirror to your windscreen. In the photos I also show the metal piece it replaces. I printed in PC blend (cars get very hot and PLA will melt) with 3 perimeters, 0.2 layer…
This small fixing eyelet makes it child's play to attach decorations to the URail track system from Paulmann. The clip is inserted into the lower guide of the track and automatically wedges itself into the track when the eyelet cap is…
Clip de remplacement pour fixer une plinthe sans vis apparente (système de la marque “Skandor”, vendue chez Hornbach). La plinthe vient glissée dans le clip une fois celle-ci fixée au mur. Hauteur du clip = 26 mm
The SV06 has a X axis twist problem. One way to help with that is to tilt each Z axis forward or backward, and this can be done with the top rod fixing blocks. This model uses the same measures as Sovol's STEP files. The 44.3mm distance…
These adapters mean you don't have to change an electrical box if the fixing supports break See how to use it on youtube… Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 200 Infill: 50…
Hawse Fairlead with adjustable fixing slot - Passacavo per verricello Overall dimensions: 300x67.5x18mm Centre to centre 254mm / 10" Standard Bolt Mount Pattern with adjustable fixing slot Mounting hardware needed M10 / 3/8" bolt…
4040 RV2 Series Foot Cap - Low Type - with predisposition for fixing with screws Suitable for: Resize to adjust dimension All our designs are free to download and use—we believe sharing drives innovation. Your support fuels our…
🇨🇿 Fixační element do kufru - inspirován elementem ze Škody Superb 🇬🇧 Fixation element for the boot– inspired by one from the Škoda Superb. 🇨🇿 Vytvořil jsem dvě verze fixačního elementu do kufru auta inspirován originálním ze Škody…
Support mural pour papier toilette, design, épuré, avec fixation invisible. Pour l'impression, bien calibrer l'extrudeur, sinon jamais les deux parties vont s'emboiter. La tolérance d'emboitement a été volontairement calculée pour être…
All my GUNDE chair by IKEA are broken near the handle. I made a simple part that prevent (or fix) this weakness. I used poxypol to join this part with the chair, but other types of glue for plastics should work. Material: PLA/PETG Wall: 3…
Support pour rehausser le nid d'abeille avec l'utilisation des rallonges de pied afin de ne pas avoir à tout démonter 4 vis de 5x20 et 4 écrous de 5 (Collé au double face sur le nid d'abeille) Maintient de ces réhausse avec une pièce à…
Prefer a rather flexible material like PETG. Simply slide from the side of the column to align its parts. Once the lock set up, pull the strip to remove.
Drying rack hook to fix loose wire. Printed using PETG with 0.4 noozle and 0.28 layer height
Small anchor so that the wind doesn't blow your beach towel away. I have printed it in PETG so that it is more durable.
The base is Made for vertical and horizontal positioning of the arm I recommend to print in a high infill (at least 40%). I made it with PLA+ 60% infilo and with an arm extended 40 cm (16 inches for American friends) and it can easily…
