holder for Hikoki battery
prints standing up
- Downloads
- 623
- Likes
- 36
- Rating
- 5
58 models
Can be printed without support upright, or with snug default supports inside the catch notches
Hitachi / Hikoki Battery Changer Wall Mount requires longer screws to mount to charger screws and feet stick out a bit further then adapter but it still works
HIKOKI HITACHI Battery holder
Hikoki battery wall mount suitable for multivolt batteries. The original file didn't fit the multivolt batteries. Edited in Blender to fit the multivolt batteries. The batteries won't fall out because I kept some resistance while sliding…
prints standing up no supports
Can be printed without support upright, or with snug default supports inside the catch notches.
Adapter to connect a Hikoki UP18DA to a SUP pump hose.
Print Settings Supports: Yes Resolution: 0.28 Infill: 20 Filament: PETG
Attaches a 2.5" Rigid vac hose to the dust port on your Hitachi-Koki 12" sliding compound miter saw. Printed at 0.2mm layer height with 0.4mm nozzle.
While searching for an efficient way to store my cordless drill, I came across several solutions. However, none of them met my requirements, so I decided to design my own storage solution. This design is specifically created for the…
Hikoki/Hitachi/Metabo C10RJ to Bosch Universal Vac 15 vacuum port adapter Print in PETG
Unfortunately, the mount I found online for the Hikoki charger didn't fit. So I designed one that fits my charger. The charger can be easily removed. Printed in PETG 2-walls with 15% infill. For easier identification, I printed the…
Wallmount/ under desk mount for Hikoki/ Hitachi Charger UC 18 YSFL Print Settings Rafts: No Supports: No Resolution: 0.3 Infill: 30 Notes: tight fit PLA works fine, use PETG or similar for more robustness Category: Tool Holders & Boxes
While searching for an efficient way to store my cordless i9npact driver, I came across several solutions. However, none of them met my requirements, so I decided to design my own storage solution. This design is specifically created for…
Hikoki Battery to Festool adaptor, the tool was powered with a nicad battery. Semi permanent installation, I used a couple of small self tapping screws to keep the adaptor from sliding out of the Festool, see the photos 4x 6mm male spade…
Fix for Hikoki tool box #1 organizer tools
Designed a ZCI for my table saw - figured I wouldn't reinvent the wheel, and make an insert for just the existing slot gap instead of the whole insert. Friction fits in the existing slot but works much better if you drill and tap the…
Small bracket that can hold Hikoki batteries. If you mount them stacked vertically, as in the image, use a CC distance of at least 165mm (~6.5in). There are a bunch of these here already, but I thought they were a bit too wasteful.
Modified version of Metabo / Hikoki C18DBAL circular saw dust port by Sekellus1 to allow use with the osVAC system. Printed with Bambu P1P in PLA. Perimeters: 3 Layer height: 0.2mm Supports: only needed on buildplate to support mounting…
It's an adapter for connect vacuum hose to the sander
Here are brackets to screw your HiKoki battery charger to a wall or even upside down on a shelf. Use only the left and right bracket to mount one charger using 3 screws (3.5x50mm) for each brackets or use the middle bracket (in between)…
This is a battery holder that can be used to mount your hikoki batteries to a wall or wooden panel. There are two holes provided to mount it to something. You will need some screws and a bit of super glue to glue everything together as…
Hikoki Absauge Adapter für osVAC System
The reducer was modeled for the Hikoki saw and the Bosch vacuum cleaner. The inner diameter of the wider side is 51mm an
POWERFULL DIY JET FAN, powered with a standard Hikoki tool-battery (21V, 5S) Printed from Transparent PETG (RosaFilaments) Everything is designed in a way that you can easily change parts, improve and adapt it to your needs, need a…
This simple mounting System works for Makita Makpac, Hikoki System Case and of course the Classic Systainer. To take out the systainer, you just lift it up.
I designed HiKOKI system case front handle referred from this model. https://www.printables.com/model/841950-makita-makpac-front-handle It uses six M5 x 15 mm socket head cap screws and six M5 nuts. The handle hinge is a common shape for…
As I wasn't able to find a battery powered planer with guides to chamfer our beams, I decided to design them on my own. It perfectly fits the existing holes on the base plate. You will need some longer screws to connect the adapter and…
A reducer from 56mm OD to 35mm ID dust ports. This one is tested with a Hikoki 216mm (8 ½") Mitre Saw.
I created this insert to suit the centre section of the Hikoki Multi Cruiser Accessory Case. Allows for easy removal. The Accessory Case has large sections, however being an electrician, I wanted smaller sections to carry more tiny…
simple wall mount for multi tools - fits hikoki no supports needed
das ist ein OSVAC Absaugadapter für den Hitschi/Hikoki SV12SG Schingschleifer/Rutscher 3 perimeter 25% infill mit Suport zu drucken in PLA+ oder PETG
Should be a tight fit, shove it in the back and get cutting, I have printed it and I am using it but i forgot to take a photo before i shoved it in the hole, soz
Universal Adapter for Hitachi Hikoki Miter Saw to conect vacuum cleaner , dust bag ,dust extractor, external diameter 52,5mm
There are two versions, the only difference is the individual mm markings - on one they are proud/raised; on the other they are recessed. Choose whichever suits your printer (they are 0.1mm width so YMMV). Printed at 0.15mm for detail…
Make a shadow line lamp on your Hikoki C8FSHG mitresaw Print part 1 and 2 I made this to use a car licenceplate bulb like a 36mm dome light LED 12V and hooked it it up to the saws original laser output (That I have removed, no need for…
HiKOKI battery BSL 1225M
a dust connector for hikoki SV13YA
a cable holder for dust collection hoses. it fits different kinds of cables for machines
this is a remake of a attachment for the sub that you can inflate with the hikoki airgun. feel free to upgrade my file
this is a simple connector for you're vacuum
A bit tricky to print horisontally due to holes and the "shims" around the pivot pin hole so it may be better standing at 45 degrees. I made mine in PLA with 50% infill and it seems to work fine.
this is a remake of the Festool router dust collection system for the Hikoki Cordless router 36v for side trims
This is a remix of the smaller M32 adapter (excentric variant), but I wanted to use a bigger M40 bajonet connector.
this print is for the Hikoki RP200YLWAZ line and will hold different brand dust bags and you can put a bolt through the cartboard for a stronger joint. Holder 1 is for hot glue only V2 is for bolt mechanism you drill a hole in the…
A replacement bottom lid for the HiKOKI UC18YKSL charger with integrated wall-mounting holes. The original charger has no convenient way to mount it on a wall, so this design lets you organize your workshop and keep your charger off the…
Vacuum Cleaner Arm for HiKOKI Vacuum Cleaner This adjustable vacuum arm keeps the hose above your workbench, so it no longer gets in the way while you work. The arm swivels smoothly and reduces hose resistance, providing greater freedom…
You can leave the screwdriver straight on in "pistol" position. In one of three orienations: left, right, center. Grab the "socket_stub" file if you want a different mounting. Top two openConnect slots are locking! It was also an exercise…
Label holders for hikoki's systainers. This allows standard label cards for systainer SYS3 fx to be used. Standard plastic business cards also fit. The small one is for hikoki systainer 1 and the large is for the rest. Use double sided…
I made it so you can adjust the cutting depth on the miter saw. I'm putting a knob made by someone else on an 80mm M8 bolt. I glued an M8 nut to the end of the bolt to make it more stable. For printing, use PETG, set the infill to 30%,…
this print is for the Hikoki RP200YLWAZ line and will hold different brand dust bags and you can put a bolt through the cartboard for a stronger joint. Holder 1 is for hot glue only V2 is for bolt mechanism you drill a hole in the…
this is a remake of a attachment for the sub that you can inflate with the hikoki airgun. feel free to upgrade my file
this is a remake of the Festool router dust collection system for the Hikoki Cordless router 36v for side trims
POWERFULL DIY JET FAN, powered with a standard Hikoki tool-battery (21V, 5S) Printed from Transparent PETG (RosaFilaments) Everything is designed in a way that you can easily change parts, improve and adapt it to your needs, need a…