Search results: plastics

Sort order

23 models

P
PrintablesDaRealestKilla

DT1990/DT1770 Outer Slider plastics

Hi, this is my custom model for the outer slider plastics for the dt1990 and dt1770 headsets which is currently (aside from this now) only available from Beyerdynamic as part of a 40-euro slider replacement kit. The part put into use by…

Downloads
169
Likes
6
Rating
5
P
PrintablesCNC Kitchen

Hand Crank Adapter for Plastics Shredder

Hand crank adapter for the Precious Plastics Basic Plastics Shredder. Fits the 20mm shaft with the 6mm groove stone. Fits a 25x25mm steel tube with 1.5mm wall thickness. Includes the suitable handle. Press in two 608 bearings on either…

Downloads
116
Likes
24
Rating
0
P
Printableskatthulu

Better buckle for brittle plastics

I printed this model in PLA and it eventually snapped where the buckle deforms to fasten (circled in red). While this design is fine for injection molded polymers like nylon, it'll wear 3d printed materials with less durability. I…

Downloads
98
Likes
22
Rating
3
P
Printablesrolmos

Gaggia locking plastics for group collar / retaining ring

Many old Gaggia machines used these plastic parts to reduce the wear caused by the Stainless Steel retaining ring and the brass portafilter. It was a bad design decision, and since retaining rings are hard to come by, this is a great…

Downloads
59
Likes
4
Rating
5
P
PrintablesShyavanS

Microplastics Mega-Polarizer

A design for a water filter made to filter out microplastics using biologically activated carbon and a plant tissue called xylem. The filtration substrates are a zoomed-in microscopic view of the actual materials. Originally designed for…

Downloads
50
Likes
4
Rating
0
P
PrintablesStephen J

BarkBuster Plastics Handlebar Clamp thingys

I purchased some BarkBuster plastics for my motorbike handlebars a year or two ago and noticed that they only supplied clamps for one of the two mounting points (each). I had a slow weekend recently and copied the original clamps in…

Downloads
49
Likes
7
Rating
5
P
Printablessp_cecadet

roof rack with ski rack for 1/10th audi avant rs6 from APPLASTICS

roof cross bars fit the 1/10th audi avant rs6 from APPLASTICS. ski rack itself has a 1mm gap between the “rubber” holders. Print your snowboard or skis to fit. I did not save the prints in any specific orientation but they are flat and…

Downloads
44
Likes
15
Rating
0
P
PrintablesSamicable

Wurlitzer Front Plastics for 2504 and 2510

Replacement front plastic logos for Wurlitzer 2504 and Wurlitzer 2510 jukebox. Notes: For the "press a letter and number" piece, print letters up with supports in the center, then change filament when you get to the letters. For the…

Downloads
39
Likes
1
Rating
0
P
Printablessp_cecadet

Front ISOGRID fog light buckets for 1/10th audi avant rs6 from APPLASTICS

Introducing the Front ISOGRID fog light buckets for your 1/10th Audi Avant RS6 from APPLASTICS - a stunning addition to your miniature masterpiece. These fog light buckets are designed to fit perfectly on the front of your model,…

Downloads
36
Likes
6
Rating
0
P
Printablessp_cecadet

Front ISOGRID grill for 1/10th audi avant rs6 from APPLASTICS

Experience the ultimate in customization with APPLASTICS' Front ISOGRID grill for 1/10th Audi Avant RS6. Choose between two distinct designs - one proudly showcasing the iconic logo and the other offering a sleek, logo-free aesthetic for…

Downloads
28
Likes
3
Rating
0
P
Printablessp_cecadet

exhaust tips for 1/10th audi avant rs6 from applastics

exhaust tips for 1/10th audi avant rs6 from applastics. These will fit a 3mm led if you want to run “backfire”.

Downloads
23
Likes
5
Rating
0
P
PrintablesPowderKeg

ASTM D638 - 14 Standard Test Method for Tensile Properties of Plastics Type V

I modeled the Type V variation according to the standard instructions provided here: https://borgoltz.aoe.vt.edu/aoe3054/manual/expt5/D638.38935.pdf . I use a laser cutter to cut my material using the .dxf file provided. Please note, the…

Downloads
15
Likes
1
Rating
0
P
PrintablesJonweb

Deburring Edge jig Cutter with side burr discharge (for wood and plastics/rubber material)

Dear Gentlemen, I took the great idea of Mr. Timo, thanks to share it, please have a look of his item https://www.thingiverse.com/thing:4318301 and I made a new design based on my needs, the parts are not interchangeable with his project,…

Downloads
12
Likes
4
Rating
0
P
PrintablesРадиша

Table tennis plastics

Table tennis plastics

Downloads
12
Likes
1
Rating
0
P
PrintablesMielkeMaker

Stylized Label For #5 Plastics

A simple model of a label to fit over a wicker basket

Downloads
9
Likes
0
Rating
0
P
PrintablesProtoMech3D

Yamaha Protection plastics conveyor (sx)

This project was born to protect the graphics from rubbing from boots while driving. Material: PETG Layer Height: 0.28 Loops: 6 Support: Trees Angle: 40 Degrees feel free to print it with your parameters, mine are already tested and…

Downloads
8
Likes
0
Rating
0
P
PrintablesBottles&Cans

Push Plastics 10kg Spool Holder for Lazy Susan

Printed on Push Plastics PLA 222/52. 30% infill, skirted. 0.2 res. Simple model for installation on a 1000lb capacity lazy susan. This spindle ‘bump’ centers and holds the spool in place while it unrolls on its side. Entire apparatus is…

Downloads
8
Likes
1
Rating
0
P
PrintablesNickBrewer

Fantastic Plastics Logo

2 Versions of the Fantastics Plastics logo. Makes a great ornament! fp_eye V1 - Solid back fp_eye V2 - Open, but delicately connected together.

Downloads
8
Likes
1
Rating
0
P
PrintablesEcobra

Assistive Communication Device Plastics

Calling this one the F-Bomb board as it is designed for a veteran who recently had a stroke and liked to swear. It conveys basic needs "I am thirsty", "I am hungry" ... and "F*** You". It also has a secondary button to tell us if he can…

Downloads
6
Likes
10
Rating
0
P
PrintablesProtoMech3D

Yamaha Protection plastics conveyor (dx)

This project was born to protect the graphics from rubbing from boots while driving. Material: PETG Layer Height: 0.28 Loops: 6 Support: Trees Angle: 40 Degrees feel free to print it with your parameters, mine are already tested and…

Downloads
5
Likes
0
Rating
0
P
PrintablesDesigner 1
Downloads
5
Likes
0
Rating
0
P
Printables

WeCreat Lumos Koozie Jig — Johnson Plastics Plus Leatherette Can Holder Alignment Fixture (STL/3MF)

Take your WeCreat Lumos laser engraving projects to the next level with this custom koozie jig , designed specifically around the Johnson Plastics Plus leatherette koozie (see stock number in photos) . This jig helps you achieve accurate,…

P
Printablessongdawgdesigns

WeCreat Lumos Koozie Jig — Johnson Plastics Plus Leatherette Can Holder Alignment Fixture (STL/3MF)

Take your WeCreat Lumos laser engraving projects to the next level with this custom koozie jig , designed specifically around the Johnson Plastics Plus leatherette koozie (see stock number in photos) . This jig helps you achieve accurate,…

Likes
2
Rating
0