PET filament machine (pully)
for pulling filament true diy hotend
- Downloads
- 511
- Likes
- 56
- Rating
- 4
Counting matching models…
for pulling filament true diy hotend
This is an OpenScad script pully module based on the pully module by by droftarts January 2012 https://www.thingiverse.com/thing:16627 Code has been completely re-written, condensed, and multiple features and options added. All parameters…
2GT 20T Pully with 5mm bore that I optimized to be printed and use M3 heatset inserts. Highly recommend printing in ABS or better. Additional parts needed per pully: M3 grub screws (x2). M3 heatset inserts (x2).
A customizable pulley. Parametric Pully wheel should not roll on a threaded shaft (screw or bolt) Doing so with pla and other plastics will force the pully wheel to become threaded, deflect to one side and jam. Generated with Openscad Use…
Pully remover for Ender 3 and alike. All the other designs I found, where quite strict with the alignment and had a long screw. This design allows for more manual alignment and the screw is shorter to decrease the scew. For me it did not…
A Paperclip zipper is created such that you can mount a paperclip can glue the 2 pieces together
bike hoist pully chipped so modeled it up and made it. you need to drill out the rivet and replace it with a screw Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .2 Infill: 20% Filament: cctree…
this is just a post of the gt2 pulleys I use for frc I don't use supports but your mileage may vary
The TronXY X5SA series printers come with basic acrylic motor mounts and poorly aligned CoreXY cables leading to the Y carriages. In CoreXY it is important that the cables leading to the Y carriages are parallel to the Y axis, otherwise…
I was getting tired to remind everyone in the house to keep my door closed/forgetting to close it myself that it inspired me to make this project. Items needed: Rope (less than 5mm in diameter) 2 wall anchors 1 Carabiner 2 screws (to…
This is a minor stylistic change to Jody_T's rail cover to match the rest of the [Better Ender 3] series of parts I've created.
Belt and Pulley (square belt) Parametric Configurable (specify pulley positions and sizes, square belt is automatically generated) Internal or external bearings. Generated with OpenScad Use Customizer
this as stated in the summery is a simple little pulley, that I used to route my VR cables but could be used for numerous other purposes. Though if you intend it to do heavier lifting I recommend printing this at an angle with tree…
I built this to suspend a bike from the cieling printed in petg it is more than strong enough. it is compatible both with 6000 RS bairings using the original desighn of roller and with 6020 RS bairings using my updated desighn the…
The chain pully helps keep the chain off of your frame when you have the back wheel off. ONLY WORKS WITH THRU-AXLE WHEELS How to use it: take off rear wheel Put axle back onto the bicycle frame through the wheel pully with the chain…
On the Sovol SV08 MAX the original sliding seats (the things that connect the X-Axis to the Y-Axis) the position of the pullys that deflect the belts aro horrorbly wrong. They cause the belts to form triangles that leads to the fact that…
I made this idler pulley to replace a failing pulley on my 25 year old recumbent bike. It can be printed in either PETG, ABS or TPU. I used TPU because for my application I wanted it to be flexible. You can press in a 626 sized bearing,…
Most shold friction fit, i used epoxy myself for secure fitting.
This carriage are design to use with a OpenBuilt V-slot 2060. I'm building a delta kossel machine using 2060 v-slot for the three vertical towers. I've use this original carriage due the fact that have a heavy duty springy mechanism using…
a simple print in place pully tolarances are big, but it will stay in place
A friend of mine has a real old Hobie Cat sailboat with an all Aluminum mast. After many years of use, the masthead pulley (Nylon with a brass insert) just fell apart from weather & use. Since Hobie no longer makes or supplies this part,…
Just some edits with about 30 more filets and added geometry for printability and strength
This sleeve will slide over the idler pully for the CoreOne Premium Coreboxx rewinding spool holder. I also added an access hole in the sleeve to get at the grub screw. Note: You must get the grub screw started before sliding the sleeve…
Doctor Doolittle - The Pushmi-Pullyu - 1967 3D printable model.
I had printed the top frame before finding out there's a version with z pulley support. So I made this instead of reprinting the whole top frame
you can use this for every you want
Belt pully 20T for Prusa i3. It needs two small ball bearing (Diameter=8mm, Width=4mm). I buy them at Aliexpress. Category: 3D Printer Parts
Material PLA+ Layerhöhe 0,2 mm Infill 100 % Support 5% Zusätzliches Material / additional material: 2x Kugellager / ball bearing 625 (Ø5 x Ø16 x 5 mm) 1x Schraube / screw M5 x 35 mm 1x Mutter / nut / M5 Gutes Gelingen und über ein Like…
The starter pull start pulley on my Ryobi Whipper snipper lost the teeth. Designed in Fusion 360, printed in PETG. Update the PETG sheared off the teeth pretty quickly. I printed it again in 90 hardness TPU and it seems to be better. I…
I converted my enter 3 to direct drive but didn't have room to mount the spool above the printer. This meant the filament came in at a sharp angle and the spool would start rocking as the head pulled the filament back and forth. This uses…
I've included a picture of the original white part that wore down over time. This replacement is designed for easy installation—simply unscrew the existing screw, place Part 1 behind the metal piece and Part 2 in front, snap them…
I made this for when I'm feeding filament from above, below or really any where so the filament has less chance to break or the tables edges.
This guide quickly snaps on and off any standard 30mm spool holder. Works great with a dryer. For assembly you will need one M3 x 30mm screw and nut.
Pulley printed in 2 parts snaps together like lego 100% infill No supports I used PLA
A real tiny part... for an denon drr-m10 tape deck.... printed on the prusa mini with an 0.25mm nozzle. Verry tiny part… its the part i point at with my tweezers, i printed it in pla but i think its gonna be better in an resin printer.
these two tools help u to align the pullys as requested in Siboor Docs one is for 13mm the other is 5mm
The MDF Rose Engine 2.0 requires a stepper motor pinion/pully to drive the spindle and the phase multiplier. Here are two 3D Printable versions I made instead of sourcing from Amazon or AliExpress. I recommend printing with PETG, support…
I made this for the Mosaic Palette 2 (or Pro) upside down on a Ikea Lack table to act act as guide for filament so it does not rub and snap.
My John Deere 445 (54" Deck) spends most of it's life outside. The powerflow pulley collects water and dirt. I made this cap from TPU to keep it clean and dry. There is a ¾ NPT threaded hole on the center to allow for easy greasing of the…
I switched from a remote dropper post to a pully operated one. Unfortunately the Simplon Kibo has no internal routing into the seat post. Therefore I used the threaded opening where normally the front derailleur sits. To protect the pully…
Here are my models for a Unimat 3 pulley cover. There are four files included... Original = this is the default model, but as it has raised surfaces on the face it maybe hard to print as you'd need a large support structure. Recessed =…
The pullme-pullyu from dr.dolittle. Category: Animals
This pulley is designed specifically to fit my 40 year old Odyssey1 Dobsonian, but by editing the .SCAD file you can adjust the diameter, thickness, etc, so it may be useful for other Dobsonian style telescopes. The handles allow me to…
Hey Everyone! This pulley and adapter are specifically made to fit MBS “Twistar” Hub Set. I think it's the MBS brand low end option for mountain board wheels. I couldn't find anything else online to fit so I made these. Pulley has 72…
For custom printers using 2040 extruded aluminum. This is a motor and pully system for the belt if using linear rods and bearing.
40 Tooth Idler 608 Pulley for GT2 2mm x 6mm Wide GT2 Belts Instructions Print at 100% infill. If your machine is well calibrated it should be a press fit from one side only with the small ridge on the other to center the 608 bearing in…
Built my MK3s as a kit and a few prints in got a squeaking noise from the Y axis. From reading the forums others have seen the same on the X axis also. These washers go either side of the idler pully. Both have a chamfered side that needs…
Printing Print with supports and a configuration like this. i printed at around 4,000% (because the model was too small)