Search results: vornado

Sort order

Counting matching models…

P
Printablesch1a

Vornado 630 Replacement Fan Blade

The blade length and hub measurements match the original, but I sort of eyeballed the angles of the fins. The hub fits snug, but should press on fine. I've been running this for a year in my shop and I can't tell a difference between the…

Downloads
1,077
Likes
42
Rating
5
P
PrintablesKipable

Vornado fan knob

The rotary speed select knob fell off of my vornado room fan, so i modeled this new one. It connects to the fan using the D-shaped rotary switch on the fan. May work for other fans as well that use the same switch. It took a few prints to…

Downloads
108
Likes
5
Rating
0
P
Printablesgniticxe

Vornado 293 Fan Knob

There are two models. One is smooth and matches the original knob. The one with a seam should force the slicer to place the z scar aligned with the indicator. The picture is the smooth version, where the seam is slightly misaligned. It…

Downloads
96
Likes
3
Rating
0
P
PrintablesDouglas Hale

Vornado transom window fan adjustment block (4 inch)

The fan only include blocks for windows up to 40", my windows are wider, so I needed additional blockers. Note the print orientation, there are small flats meant to interface with the bed. I recommend using a brim and supports (as shown)…

Downloads
93
Likes
13
Rating
0
P
Printables3DeezNutz

Vornado fan feet TPU

I seem to always loose them Or it drops into oblivion. never again replacement feet for Vornado fans. please leave ⭐ review and rate. Buy me a some raman if i helped you out in anyway. https://ko-fi.com/3deeznutz Check out my other…

Downloads
84
Likes
13
Rating
5
P
Printablesmsy

Vornado Replacement Knob

A replacement knob for Vornado and other fans

Downloads
65
Likes
5
Rating
0
P
PrintablesAtomichaze

VornadoAir 530 Switch

This is a switch for the VornadoAir 530 fan. You need support and slow print between 20- 40 mm/s.

Downloads
51
Likes
1
Rating
0
P
PrintablesShinobu Tezuka

Transom Vornado Window Fan Expandable Vertical Mount

BOM: M4 Socket head 20mm x 3 M4 Heat Inserts M5 Counter Sink 12 mm x 8 M5 Counter Sink 16 mm x 8 M5 Heat Inserts 10mm or 6mm x 8 M5 Bolt H:4.70mm x 8 Ball plunger 8x9mm x 1 (Ball Plunger Set) This design is for casements with these…

Downloads
43
Likes
4
Rating
0
P
Printablesniget2002

Vornado 173 Wall Mount

This is a mount for the Vornado 173 fan. It uses the stock screw holes that are used to install the stock base. The ‘left’ mount has provisions to use a small bungie or zip tie to hold the fan to the mount if needed. The STL for the left…

Downloads
28
Likes
4
Rating
0
P
Printablesmchangcreative

Vornado Silver Swan oscillator turning axle

I printed with PETG at 0.15mm layer height. I used 100% infill and turned on “bobstro's supports," which are saved in the .3mf file. The tall end of the axle attaches to the large plastic gear with a screw. The other shorter end rests…

Downloads
25
Likes
1
Rating
0
P
PrintablesAlmightyFireFly

Vornado PivotC Clip Fan Desktop Base

Fan friction fits into base. Works great at office desk.

Downloads
25
Likes
2
Rating
0
P
PrintablesKruscle

Vornado 602 Fan Desktop Base

Fan base I made to save some floor space. Made for my fan- the Vornado 602, but it may work for other models. The neck for the 602 is roughly 48mm in diameter, so if yours are similar spec, you may be in luck! That being said, I've…

Downloads
22
Likes
1
Rating
0
P
PrintablesBill

Vornado EX05 replacement blade.

Replacement blade for a vornado EX05 fan. I printed it in ASA for head resistance in the back of my truck

Downloads
18
Likes
1
Rating
0
18+

The source marked this model as adult content.

Downloads
18
Likes
2
Rating
0
P
PrintablesEccentrical

Vornado 279-TR TPU Fan Feet

I kept losing the Vornado silicone anti-vibration feet. Without the feet, the fan makes an annoying buzzing sound. These TPU feet prevent that noise. Depending on your shore hardness, it may be a bit difficult to insert these feet. Make a…

Downloads
15
Likes
0
Rating
0
P
PrintablesDuIslingr

Vornado AIRBAR 4 Bedframe Holder

Wanted to mount the fan on our bedframe so made this model to facilitate that. The gap of which it rests on the frame is 3/4", so any frame similar to the one pictured and linked it should work as is. Fan:…

Downloads
15
Likes
1
Rating
0
P
Printablespandao

Vornado 660 Replacement Foot

I kept losing the rubber feet at the bottom of my vornado and it kept sliding around and vibrating on counter so I modelled a replacement. Printed in TPU.

Downloads
14
Likes
0
Rating
0
P
PrintablesBrian Hanson

Vornado BXR Horizontal Door/Wall Mount

Do you have a need to install a horizontal fan above a door frame? Perhaps you have a room that produces more heat than you would like, with no central air, and you need a good way to circulate the air. Then look no further than this…

Downloads
13
Likes
0
Rating
0
P
PrintablesGrant Emsley

Vornado Model 184 remote battery cover

This is a replacement battery cover for a Vornado fan remote control. Remote says Model 184 on the back. It doesn't fit perfectly, but it works well enough. Fusion 360 files included if you want to adjust it for a better fit. Print…

Downloads
13
Likes
0
Rating
0
P
Printablesbrchr

Vornado 133/533/633/683/753 leg fastening nut

I printed in PETG at 0.08 mm layer height, but I think it would work fine in PLA or other resins, too. The small layer height helps keep the threads smoother.

Downloads
12
Likes
1
Rating
0
P
PrintablesStephen

Vornado Duo Compact Tower Circulator Fan Wall Mount

A simple wall mount to convert the Tornado Duo Compact Tower Circulator fan in to a wall fan.

Downloads
10
Likes
3
Rating
0
P
Printablesdeath4u

vornado fan replacment feet

These are replacment feet for Vornado fans. Vornado_foot.stl should be printed with tpu. My printer was having problems printing tpu so I made a mold for casting rubber feet. I mixed silicone with cornstarch and pressed it into the mold.…

Downloads
10
Likes
0
Rating
0
P
Printablesjwillo

Wall Mount for Vornado Pivot3 Clip fan

I bought this fan expecting to either mount it to my desk or figure out a bracket like this! It wasn't super hard to pop the stock bracket off and frankly the stock bracket feels like the cheapest part of the fan Rotate the STL slightly…

Downloads
8
Likes
4
Rating
0
P
PrintablesJordan Pizza

Vornado (VMHi300) Knob Replacement (with small lever)

Replaces the original knob for my Vornado VMHi300 - so it allows easy control from where we keep it on the floor. The original knob wasn't super accessible so we made it easier to toggle. Includes a small pointer for the mode it's on.

Downloads
5
Likes
0
Rating
0
P

Vornado Evap40 Humidifier Slow Drip Cover

Simple print two of these and clip them onto the front of your tanks after filling. Any nozzle size should work, but a 0.2mm nozzle will likely work best. Any print settings should work.

Downloads
3
Likes
0
Rating
0
P
Printablesneopifex

Clip-On Shroud for Vornado Zippi Fan

The Vornado Zippi is a good little fan. It has cloth blades and thus doesn't need a cover of any kind, but it still moves a decent amount of air for a personal desk fan. I have multiple Zippis for home, work, and workshop (this is not an…

Downloads
0
Likes
0
Rating
0