Zaxquag
Use supports.
Print approx. €0.64–€0.78 excl. taxPreliminary estimate for one variant
- Downloads
- 9
- Likes
- 1
- Rating
- 0
33 models
Use supports.
Print approx. €0.64–€0.78 excl. taxPreliminary estimate for one variant
Benefits for the part: prevent dust from entering the stepper motor perfect fit and easy to remove inspired by prusa design little use of materials, great benefit Before you start printing, load the file into the slicer and add the same…
None of the existing z-axis stabilizers for the Ender 3 V2 fit correctly or used M5 bolts with drop-in t-nuts to attach so I created my own. You'll need (2) M5 x 8mm bolts and t-nuts and a 8mm x 22mm x 7mm ball bearing . The bearing is…
Codemonkey1973's Ender 3 Camera Mount for Raspberry Pi Camera V2.1 was very well designed but I wanted to cleanly route the cable to the back and saw room for improvement. So I rebuilt it with the following improvements: Threaded holes…
Miniature of the beholder “Xazax the Eyemonger” from the Dungeons and Dragons Adventure “Out of the Abyss”. Details : The miniature comes in a total of 22 parts for easier printing and painting Also included is a combined version that…
I made a cover and a stiffener for the Z-axis bearing in the Anycubic Kobra 2 printer. If it doesn't fit on the bearing, you need to slightly enlarge the hole with a scalpel. Original screws were used, which also need to be screwed into…
A new printer was purchased, and immediately began to experience printing problems. Once again, going over the kinematics, I found barely noticeable cracks in the fastening of the Z-axis motor. I made a new one, maybe it will be useful to…
Want to access even more models not found here ? Interested in supporting my efforts making free models for the world to enjoy? Check out my patreon page here: https://www.patreon.com/mz4250 or support me on Printables Clubs! Patrons have…
Simple friction fit adapter for basic skate bearings (outer 22mm, inner 8mm).
Quick printing wire strain relief for wire antennas. Center hole for connecting stuff. Has a gentle curve as to keep wire from de-sheathing. I kept de-sheathing some thin wire with a simpler strain relief so whipped this one up... The…
Simple and cute quick printing case for the Heltec E213 eInk node. There's even a little room for a battery if you're so inclined. Whipped this together for my desk and though I would share if anyone else with the same node wants it...…
I love the original Morse Code Paddle / CW Key that K6ARK made. I was trying to get the contact distances closer but had trouble with the pressure from my plastic springs not being enough. With magnetic returns I was able to get the…
Was missing this one, and someone asked for it :) Hope it helps, also hope it fits, didint test myselef yet. Stay frosty! All hand down to Chris Borge (Original creator or RSMM cnc) Having fun putting it together and making a list of…
Printer: Anycubic Kobra Go Orientation: Lay flat, see screenshot Supports: Trees with Support Interface Resolution: .16 Infill: 100% Concentric Filament: Zirro Glow in the Dark Blue PLA I have been searching for a good camera mount for…
9/7/24: Reuploaded the correct thicc pump files. 29/6/24: Added the top pump for MGN9H rail (I've only tested for C rail, should work the same regardless). Added a shroud base that works with the older lynx receiver without the…
Filament Spool Holder for Zaxe X1/X2/Z3 3D Printers Instructions: Place the model in your slicer as in the picture Take your print from the bed and rotate it 90 degrees on the Y-axis Insert it through the opening at the back of the Zaxe…
Here is the mini clip for the build plate. Ideal printing material is PA6-GF, PA6-CF, or similar high-temp materials.
QMX Buddy Back Case non-destructive replacement for rear case panel. Quick to swap with existing screws to allow room for your mods. Use your slicer or cad to poke holes in where you want them. Maintains the nice aesthetic of the QMX. I…
Prusa mini - zaxe xlite stealthburner adapter (not tested)
3KG spool holder for Zaxe Z3 and Z3S printers
Zaxara has been sitting half painted on my desk for over a year but I finished it. on the off chance any of you are interested in my Zaxara deck here's the decklist , I like playing Bracket 1 so don't expect a powerhouse If you want to…
VE7ZAX QMX Speaker Easy quick speaker project for the QMX with enough volume for indoor and non-noisy SOTA/POTA use. I wanted a simple, tidy, clutter-free way to listen to my QMX without headphones so I whipped up the ear-popping menace.…
For Zaxcom RX200 battery doors that the screws threads have stripped. Two models, on has a rib along the back for added strength.
This is a combination of the ZAX TPU buttplate QD Ergo Stock Lynx 2.1 remix and the Kelly Industries QD Ergo Stock Lynx 2.02 Remix. I like the metal insert found in the Kelly Industries The nut side of the QD insert is unchanged from the…
Easy little project that makes for a fast stable mount for your whip antenna on a rocky summit or anywhere else. Two crossed trekking poles, or a couple of sticks at the base are held in place with two velcro straps. Just posting this is…
I love the EmTech ZM-2... I decided to make a mini version of my ZM-2. This case fits all the bits in a compact package. 15W BNC only. This is an exact clone of the ZM-2 but I omitted the balanced antenna ports and switch. Used the ZM-2…
Simple and minimal clips for the QRP Labs QMX that let you use your Nitecore NB5000 Air power back as a stand making a tidy setup. Posting for the nine other people that have a QMX and a Nitecore NB5000 Air. Thanks for any likes and…
Spool holder for Zaxe X1 with roller. Remixed by using https://www.thingiverse.com/thing:3209211 and https://www.printables.com/model/246605-zaxe-x1x2z3-spool-holder/files
IF YOU WISH TO REMIX THIS PLEASE TELL ME BECAUSE YOU HAVE TO PAY A FEE TO GET THE RAW FILE, THANKS, -IDONTCARE
It's a TPU comfy grip for the TUMD CW paddle and flips around to protect the keys when it is packed up in your bag. I'm quite fond of this key and wanted a minimal protector for packing it that also made it a little extra comfy and easier…
VE7ZAX Begali Simplex Lower Profile Paddle replacements. Alternate paddles for the Begali Simplex. They do two main things I wanted. The bring the pads closer to my desk so I don't have to hold my fingers up so high and also have the…
Simple and cute quick printing case for the Heltec E213 eInk node. There's even a little room for a battery if you're so inclined. Whipped this together for my desk and though I would share if anyone else with the same node wants it...…