85 models
🇪🇸⚽ 🏟 Welcome to northern Spain! 🔵⚪ Mendizorrotza or Mendizorroza is a football stadium in Vitoria-Gasteiz, Álava, in the autonomous community of the Basque Country. Opened on 27 April 1924, it is the home ground of Deportivo Alavés, a…
I really like the zorro, but I needed something to protect the gimbals in my bag. So I whipped this together. It's a simple gimbal protector for the radiomaster zorro. Rotate 180 (print upside down) in your slicer to print without…
Case for the Radiomaster Zorro without external module. -Place supports under the latch part of the case! -Hinge: M3x48 screw and M3 Nyloc nut -Latch: instructions->link remixed from roadie3rd https://www.thingiverse.com/thing:2425378
Altura de capa 0,2 Impreso con AMS a 4 colores . (Amarillo, Blanco, Negro y Rojo) Relleno al 15% Altura total de 3 mm (Se puede modificar escalando en Z) Impreso sin soportes.
This a Remix of the design of @HandsomePotato The middle part is reinforced
Blade pieces are numbered in the upper side: Front[1-4] & Back[1-5]. You need 16 pegs for alignement. The grip piece is not reversible, the upper part is marked with T (top). As the thickness of the guard was very thin I used filament as…
This case holds a homemade 18650 battery pack and mounts to the nano module interface on the rear of the zorro. The pack can be easily removed for charging when needed and will easily power the radio for hours on end without using the…
I soldered 24awg PTFE wire to the batteries and ran them through the hole on the top of the radio. I kept the original 18350s in to keep it balanced. You can also use a small 90 degree usb-C adapter so you can still have access to the…
A simple screen and switch protector for radiomaster zorro. This is my 1st cut but fits well.
A little model I made of a cat as I learned to make models.
I wanted a small handle for my Radiomaster Zorro to make it easier to carry when it wasn't in its case. There are two versions, one with holes to screw into with some M2 bolts and one for threaded inserts to go in. Both versions need 2 x…
This is a backpack that houses a 2s 18650 pack and mounts to the zorro's nano module bay. I liked the original design of turnerd, but it had some flaws. It wouldn't fit when printed in a rigid material. I've extended the module adapter…
Gimbal protector for Radiomaster Zorro.
RadioMaster Zorro Gimbal/Stick Protector [Updated: 31/03/2024] Features [31/03/2024] Updated Now fits stick ends diameter up to 15mm ± 1mm Get the same stick ends from this stick ends set Clamp dimensions Bridging edges and connections…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Radiomaster Zorro battery extension holder for a Radiomaster LI ON 5000mah Battery. Tight fit, No special settings needed. I printed mine in PLA. --------------------------------------------------------------------------- Halter für eine…
Hello, This is a Ikea Skandis Pedgeboard Mount for the Radiomaster Zorro. It snaps in with a click and is simple to print without supports.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This design uses m3 x 4mm heated inserts and m3x8mm bolts for the handle and m2x10mm bolts to mount the base to the radio. I changed the overall shape and look of the handle and beefed up the base mounting tabs as the original seemed…
Precioso Zorro naranja en miniatura, es un proyecto experimental de trabajo con IA para crearles a mis primos pequeñós muñecos, basado en las especificaciones que me dicen ellos. ⭐Caracteristicas: ✔Modelo multicolor para ams (Bambu Lab).…
Quick remix of Switchs Protectors to be use with Meat Sticks Ends I used Tinkercad https://www.tinkercad.com/things/j14xQvA1ouP
The Mark of Zorro - Zorro (Tyrone Powers) with Tornado - 1940 3D printable model.
Radiomaster Zorro 18650 addon backplate holster mod. 2s2p 18650 to add your zorro battery capacity. Radiomaster Zorro lacks battery capacity. This helps a lot. You can glue the JST connector to this and make short balance lead.
I really like foxes and i always lost my usb so i came up with the idea of making a keychain for my usb the drawing is not mine i just did the conversion to 3d unfortunately i couldn't find the author Español: Me gustan mucho los zorros y…
WANTED: Monkey D. Luffy – One Piece 3D Print Poster! 🏴☠👒 Are you a One Piece fan looking for a unique collector's item? Create your own three-dimensional WANTED poster featuring Zorro ! This project is the perfect way to bring a piece of…
Es un modelo hecho por mi sobre una imágen plana en papel.
I did a case to place into my bag back and avoid to damage it. the case is designed to let the additionnal antenna in place. 2 holes are on each side and could be used as screw cases. you just have to print a lid. Print Settings Printer…
Image retouched for transformation into STL. Thanks for liking it.
Radiomaster Zorro Neck Strap Balancer and GoPro Mount Designed to be secured with M4/M5 Screws and Nuts The screw in the photos is a M5x20mm (I don't have a shorter screw ATTOW) See the last image for the dimensions Print Settings…
A new 3D figurine generated by AI, a Chibi Zorro (Don Diego De La Vega). Do not forget to LIKE, to download and to upload your makes, thanks ! Powered by Image-to-3D from MakerWorld (https://makerworld.com/makerlab/imageTo3d)
After many iterations, I've finished my gimbal guard for the zorro with the AG01 MINI gimbal upgrade and thumbgrippies thumb drops. The design fits into the recesses of the AG01 gimbals to remain in place. It's a good friction fit when…
The Mark of Zorro - Don Diego Vega (Tyrone Power) and Lolita Quintero (Linda Darnell) - 1940 3D printable model.
Super minimal holder for 18650s on the Radiomaster Zorro
work in progress, please comment links if someone else designs something with it or completes it! thanks have a great day.
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 180x240mm in size You may print at higher layer heights below the Min Depth of 0.48mm The Max Depth is 2.2mm and the Actual Depth is 2.2mm…
Wanted to make a handle for my zorro but didn't have any M2 nuts to assemble CapnBry's handle. So, I made one with an integrated hinge. It will likely be hard to press the two mount pieces onto the handle and after first installing the…
I based the design on an existing one but remodeled it to support wider stick ends, better symmetry, a tighter fit, and customizable text. The gimbal guard I created can support any sticks that will fit inside the 18mm inner diameter and…
It can hold a Sword in its mouth
A power switch 3/32 hex key holder and screwdriver holder for the Radiomaster Zorro
Stripped the spur gear on my Nitro FTX Zorro so I recreated it to 3D Print. The dimensions are exact to the real spur gear, you may need to scale up the design in your slicer. I had to scale up by 1.5%, this is very important if you want…
This was a special request by a friend, so I'm uploading it by itself. :) I'm open to commissions for custom meeples. If you're interested, send me a message. This miniature is sized for Meepleverse and for the latest version of Pocket…
My fingers have nothing else to slide on... Printed from PLA
Remixed from https://www.thingiverse.com/thing:5100822 but much stronger. I have a case missing many of the internal parts and found this one. When I first printed it, it worked but broken when attempting to use it with any cards. Its…
I pitch and I finally got sick enough of my fingers sliding around on the pots so opened up the radio removed the pots and fired up F360 and designed these little covers to fill the empty gaps in the radio after the pots were removed..…
Taken from a photo transformed into a line drawing then retouched to obtain contiguous lines. Be carefull when removing from the bed, they are very thin parts. Best results with thin walls option . Please like it.
This system of guards protects both sticks, the switches, buttons and wheels on the top of the radio, as well as the screen, all incorporated into one neat fitting unit when locked together. Installation is simple. Install one Stick &…
RadioMaster Zorro Short Stick Conversion Shortens the normal stick height by around 2mm. Prints with no supports but you might need an outer brim depending on bed adhesion.
I want to fix 2 things from original model: 2 battery the wire line is not perfect, so I hide them inside the case. Just print it with PETG, you will need 2 insert thread for the handle, and multiple M3 screw. thats it. Tip: if your…
This mod is for Radiomaster Zorro with the main board v2.2. Note the missing component circled in red. Other versions of the main board have this component installed and may make fitting the larger holder difficult. The original CR1220…
This mount will hold your RadioMaster Zorro on your Wall Control and other pegboards. This should work with other pegboards that have one inch spacing on the holes. There is a retaining clip on of the pegs so be careful when removing.…
A simple stick protection for Radiomaster Zorro, Really easy to print Print it in TPU to easily push stick in and out. I've been using it for a year and a half, really practical. btw, Since you have 2 sticks you need to print two of this,…
Original one fit great, just need to add a bit more plastic to the bit that holds the card in. Category: Computer
RadioMaster Zorro Gimbal Face Plates To be used when changing the radio to Mode 1, left hand throttle, right hand steering as normal on all stick surface radios. Additional Parts 4 x M1.6 x 8mm cap head screws .
He creado un zorro en versión lowpoly con inteligencia artificial
Upgraded the case to have a lid with a hinge
Step into legend with this masterfully crafted 3D printable STL model that captures the iconic masked hero in stunning detail. This remarkable figurine showcases Zorro in his classic wide-brimmed hat, flowing cape, and signature…
FTX Zorro Carnage & Bugsta RC Car Rear Mudguards Fits part number FTX6321 I print in TPU95A Flexi, but you could use PLA+ or PETG. I printed these for my FTX Zorro Brushless but the FTX site advises FTX6321 also fits the Carnage and…
After seeing Seth from Team Just Cuz Robotics using his version in his robot combat videos I wanted one. I attempted to print his version with the multiple TPU filaments that I had on hand in the orientation that was shown but was unable…
This is a holder for the Radiomaster Zorro controller. It is mounted to the Triple Helix driver's station. The spacers are held by ¼-20 button head cap screws.
Print with 0.2 layer hight and pause for the last 2 layers and change filament color if you want. no Support
Descubre la magia de la aventura con nuestro encantador modelo 3D "Zorro Aventurero". Este adorable zorro, con su expresión valiente y su cola juguetona, es perfecto para los amantes de la fauna y los coleccionistas de figuras. Ideal para…
El personaje de "EL ZORRO" diseñado 100% por mi en estilo FUNKO POP Altura: 10 cm Tiempo de impresión: 1 h 50 m Parámetros de impresión 3D Filamento PLA Boquilla de 0,4 mm Capas de 0,2 mm Temperatura extrusor: 215 grados Temperatura de…
Detailed 3D printable Michael Jackson As Zorro figurine, ready to print on FDM in PLA. Usage & Links Personal use: print freely. Commercial/digital redistribution is only allowed with a valid Patreon license:…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 100x178mm in size You may print at higher layer heights below the Base Thickness of 0.48mm The Max allowed Thickness is 1.84mm and the Actual…
~95a TPU use PLA as Support when possible
Zorro wall decoration. Print background in transparent, to match wall or contrasting color. Can be printed with any printer that uses pause/filament change. There is only one (1) color change.
Key Features: Multiboard Compatible: Designed to snap seamlessly into the Multiboard hex grid system. Tailored Fit: Perfectly matches the geometry of the Radiomaster Zorro for a secure hold. Clean Organization: Gets your radio off the…
Garfield Zorro Ring Figure is a character mashup 3d printable figurine model combining garfield with a zorro themed ring pose for display and collecting. This stl works great as a tabletop collectible, desk decor, cosplay accessory piece,…
This is a simple battery holder for the Radiomaster Zorro that holds the 2S battery tray that come with the TX16S. It is a bit tight but that is for friction fit. Original fusion model included for editing. This does not touch the scroll…
A jig with a variety of holes and slots for the different lighter mods I do. Unlikely to be of much use to other people, but I'm uploading it anyway so I won't lose the files - and in the unlikely event someone may find it useful. Takes…
This is a remix of a mount for multiconnect. The connector is replaced with one that you can use on opengrid.
i replacment for the trailing arm mount on the ftx outlaw or zorro (fits nitro zorro as well) snapped mine after heavy landing (😂😒) needs a bit of fine tuning but it will push in, uses stock fitting feel free to remix (if you can)
FTX Zorro Carnage & Bugsta RC Car Rear Mudguards Fits part number FTX6321 I print in TPU95A Flexi, but you could use PLA+ or PETG. I printed these for my FTX Zorro Brushless but the FTX site advises FTX6321 also fits the Carnage and…
I really like the zorro, but I needed something to protect the gimbals in my bag. So I whipped this together. It's a simple gimbal protector for the radiomaster zorro. Rotate 180 (print upside down) in your slicer to print without…
The Mark of Zorro - Zorro (Tyrone Power) - 1940 3D printable model.
The Mark of Zorro - Don Diego Vega (Tyrone Power) and Lolita Quintero (Linda Darnell) - 1940 3D printable model.
The Mark of Zorro - Zorro (Tyrone Powers) with Tornado - 1940 3D printable model.
The Mark of Zorro - Zorro (Tyrone Power) &N Tornado in Action - 1940 3D printable model.
![Radiomaster Zorro Gimbal Protector [Updated]](https://media.printables.com/media/prints/656310/images/6383851_8a45bf32-86ee-4d20-b024-95f1a2401efc_51cd78fa-4a95-4015-a0c4-142f78991a0f/20240331_224750.jpg)
