Counting matching models…
The original 10" model was too wide for my rack, so I created this narrower remix. It cuts away a great part of the screw guide, but the M3 hear-set inserts are entirely in the front plate, so this should not be a problem. I suggest…
NOTE: I am still working on the RAMPS 1.4 config file with Marlin 1.1.0. Currently the printer does move around and extrude slowly, but not print worthy just yet. Testing parts to upgrade my 101hero from its gear reduction steppers to…
Simple 4cm standoff for 1HE 19Inch rach equipment. Through holes are M6 for M6x60 screws. Printed in PETG with 50% infill for heavier equipment.
This is a case for the LCD2004 panel printable by the 101Hero. Thanks to RenatoT for the knob and BrantPeery for the base model for the shell. Print Settings Printer: 101Hero Rafts: Doesn't Matter Supports: Yes Resolution: 0.18mm Infill:…
1HE 1U Cablemanagement. 26 x 66mm space for cables.
I needed a way to mount my 19"(10" should work too) Switch to my TV Board. I came up with this solution, just print both pices, clip your racknuts into place, screw it to your device, then mount it with standard screws on your furniture.…
Brauchte für einen Lancom Switch einen Wandhalter also schnell mal eben konstruiert. Diese Version ist aber universal. Er ist 44,3mm hoch also etwas Toleranz ist eingerechnet da ich ihn aus ABS gedruckt habe und es immer leicht schrumpft.…
The little plastic fantastic is a little wobbly out of the box. I made some X bracing to stiffen it up. The braces have holes for screws, but I just used some double sided tape and it sticks on just fine. 1 drawback is that one brace…
Festplatte 1HE 19" Rackmount Filament: PLA Infill: 20%
Dieser 1HE Kabelhalter ist die perfekte Lösung für einfaches und geordnetes Kabelmanagement im 19" Schrank. Ideal für den Einsatz in 1HE Einheiten, bietet der Halter eine stabile Möglichkeit, LWL-Leitungen und andere Kabel sicher zu…
This is a pylon cap for increasing the structural stability of the 101Hero and was designed by Colin Klapka. This is being added here to keep all 101Hero upgrades I used in one place. Print Settings Printer: 101Hero Rafts: Doesn't Matter…
I took the top mount and made some adjustments for a sturdier fit. Inside the notched end is 20mm to prevent the bracket from sliding Two corners of the inner fill are curved so the bracket rotates in and locks. Print two of these to…
This is a remix of a fan shroud and the E3Dv6 carrier created for the 101Hero. Print Settings Printer: 101Hero Rafts: Yes Supports: Yes Resolution: 0.18mm Infill: 20% Notes: Supports to the bed are important. If possible, it would be good…
I remixed two models to fit to my purpose. I needed a rack mount for my Netgear GS308EPP and my Raspberry Pi CM4. Therefore I adapted the left rack mount base with some different spacings to fit the GS308EPP (75mm spacing) little loose…
This is a small clip to mount a Logitech C210 webcam to the top support of the 101Hero. The wide crossbar is meant to hold the support arm of the camera stable so you don't need glue/tape/etc. to keep the webcam in place. Print Settings…
This is a hotend & active cooling carrier design for an E3Dv6 hotend and 2 40mm blowers. The fit of the ducts is very close to exact, so it may take some filing on the carrier to get them to slide into place. Once in place, I would…
Tested with PLA+ with 25% infull and supports (for the screw holes) Requires 2 Screws: M2.5*8 to replace the existing screws at the side without the OLED screen.
This is a simple square dish for an upright NEMA17 (42mm) to sit in on top of the 101Hero frame and has a cutout for the motor connector. The two screw holes are spaced for the spare mounting holes at each tower. Print Settings Printer:…
These mounts allow you to hang the Sanguinololu LCD panel from the top of the 101Hero. Simply attach the mounts to the back of the board. The left hand mount has a cutout for the SDCard reader. Once attached, attach to the top of the…
This is a remix of Xerrako's struts to make a shorter set to be installable under the build plate to remove the chance of the arms striking the struts. Category: 3D Printer Accessories
19" 1HE Raspberry (2, 3) Rack Mount, with space for two LEDs (⌀ 5mm) and a tactile button (6mm x 6mm).
Created by Xerrako's to make the 101Hero sturdier and less likely to move while in use. Print Settings Printer: 101Hero Rafts: Doesn't Matter Supports: No Resolution: 0.18mm Infill: 20% Notes: Supports shouldn't be needed. Category: 3D…
This remix of the Modular 19" Rack Mount modifies the 1HE brackets by adjusting the mounting hole width for improved fitment. With these changes, the brackets should now also be compatible with 10" racks, expanding their usability beyond…
I remixed two models to fit to my purpose. I needed a rack mount for my Netgear GS308EPP and my Raspberry Pi CM4. Therefore I adapted the left rack mount base with some different spacings to fit the GS308EPP (75mm spacing) little loose…
19" 1HE Raspberry (2, 3) Rack Mount, with space for two LEDs (⌀ 5mm) and a tactile button (6mm x 6mm).
This remix of the Modular 19" Rack Mount modifies the 1HE brackets by adjusting the mounting hole width for improved fitment. With these changes, the brackets should now also be compatible with 10" racks, expanding their usability beyond…
Description: Additional cooling by separate 1HE19 front plate/spacer fan for the Qotom Q20300G9_QDNV01. Model 1 : Crafted for folded Penn Elcon 1HE19 R1268/1UK (Blind) (~inner h= 41.6 d=10.2mm). x2 Ruthex M4 thread insert holes 5.6mm @…
