34 models
Simple case for the ESP32-2432S028 Cheap Yellow Display (CYD). Held together with four m3x10 pan head screws. No supports but you'll have to clear the 3mm screw holes in the back plate. Note that I've already adjusted the alignment of the…
Print approx. €1.45–€1.77 excl. taxPreliminary estimate for one variant
Basic case for USB-C version of the ESP32 2432S028 2.8" module, also known as Cheap Yellow Display (CYD) / CYD2USB.
This is an enclosure for the Sunton ESP32-2432S028R development board widely available from Ali Express, Banggood, Amazon, etc. The cost on Ali Express is only about $8 USD. The board includes an ESP32 WROOM-32 module and a 320 x 240 2.8"…
Remix of the enclosure designed by @mdkendall for the ESP32 Cheap Yellow Display (ESP32-2432S028R) found on Aliexpress & similar sites. Model adjusted for the USB-C board version, which does have slight variations of the connector…
This is a small protective case for the following Sunton board: ESP32-2432S028 Note: You'll need 2x M3*4 bolts to attach the PCB to the casing. If you are looking for additional electronics projects, checkout the following page:…
I needed a case for the CYD (Cheap Yellow Display) that was thin enough to use 180° USB adapters. The existing cases was too thick so I designed my own one. The case have a cutout for the RGB LED on the backside and “buttons” for the…
Full enclosure for the ESP32-2432S028R (CYD). Gives you access to most of the ports on the device and has flex tabs to press the buttons on the underside. Hardware needed (4) - M3 x 5mm x 4mm heat-set inserts (4) - M3x6 socket head cap…
This is a remix of the really nice case by @Dsk001 . The original can be found here Alien3D Deck This remix has changed the following: Changed to using inset M3x12 socket head screws Removed logo(s) (I needed a cleaner look) Cleaned up…
Stand for the NERDMINER ESP32-2432S028
You don't need to use any thread inserts because board fits exactly. But you can use it and hide screws inside. Material: Whatever you want Infill: 5% Supports: NO
BOM: 1. 4 nos. FHCS M3x10 2. 4 nos. 8mm anti slip silicone bumper (optional)
This is a custom-designed enclosure for the Sunton ESP32-2432S028R development board, a popular and affordable (~$8) module available on AliExpress, Banggood, and Amazon. The board features an ESP32-WROOM-32 module and a 2.8-inch 320 x…
Modified backplate with larger clearances
A display stand for the cheap yellow esp32-2432S028 with USB-C Category: DIY
Desk stand for X-Touch using a ESP32-2432S028R. Use 4x12mm M3 screws to secure the front to the back. Use the USB cable connected to the supplied power cable to the ESP32-2432S028R (see photo).
👍 Do me a big favor and hit the Like button! ✨ This 3D‑printed enclosure is designed for the ESP32‑2432S028 2.8" smart display module . It’s a compact and clean desktop housing that can be placed on a desk, shelf, or table. The integrated…
added a place to put a 4mm stylus
Simple stand. Allows the ESP32-CYD to be placed vertically or horizontally. The bottom of the stand has a 10mm circular groove for placing a rubber pad.
Nerdminer wall mounted holder
its a case for the 2432S028 CYD without the button hole in the picture
Full enclosure for the ESP32-2432S028R. Gives you access to majority of the ports on the device and has tabs to depress the buttons on the underside. For the assembly you will need (4) - 3x5x5MM heat set inerts and (4) - M3x8 SHCS
A simple holder designed for the ESP32-2432S028 USB-C Module , also known as the Cheap Yellow Display (CYD2USB) . The holder can be mounted in either orientation. Additional hardware required: 2 × M3 × 6 mm screws 2 × M3 × 10 mm screws
Requires four M3x12 socket head screws. These can easily be found on amazon or aliexpress and look like this:
# ESP32-2432S028 USB-C 2.8-inch Touch Display Case A two-piece case for the ESP32-2432S028 / S028R 2.8-inch 240×320 touch-display board, commonly known as the Cheap Yellow Display (CYD). This version is designed around the USB-C board…
Case for USB powered cyd. Corners of the screen are slightly covered due to my desire to have rounded corners.
The screen I bought for XTouch doesn’t match any of the revisions found online, so none of the existing cases fit. I combined and modified two designs I found, and ended up with this. Maybe it’ll be useful for someone. The enclosure was…
If you like my design and plan to download it, please show your appreciation by giving it a like!! SUMMARY / DESCRIPTION This 3D-printable, two-part enclosure houses an ESP32-2432S028R board (the "CYD" with a 2.8" resistive touch screen,…
If you like my design and plan to download it, please show your appreciation by giving it a like!! SUMMARY / DESCRIPTION This 3D-printable, three-part enclosure houses an ESP32-2432S028R board (the "CYD" with a 2.8" resistive touch…
Full enclosure for the ESP32-2432S028R. Gives you access to majority of the ports on the device and has tabs to depress the buttons on the underside. For the assembly you will need (4) - 3x5x5MM heat set inerts and (4) - M3x8 SHCS Both…
Features Designed for the ESP32-2432S028 2.8" touchscreen Internal mounting for an AA battery box Space for a 5 V boost converter Screw-together construction Required Hardware You will need: 1 × ESP32-2432S028 / CYD 1 × AA battery box 1 ×…
Hey all! So this is a stand based around @ mdzi 's ESP32 Cheap Yellow Display (USB-C version) Enclosure (ESP32-2432S028R) model to help enclose the display. I may have a few of them just mining away with an alternate NerdMiner OS. Is it a…
Here is my enclose for a CYD that I use for Tessera on Home Assistant - though it could be used for other CYD applications. In my application I have added a BME280 and PIR (AM312) sensor, that means that as well as providing touch screen…
A display stand for the cheap yellow esp32-2432S028 with USB-C Category: DIY
