Counting matching models…
I was looking for a very simple 2GT belt clip and couldn't find anything that didn't require additional hardware for an open belt so I came up with this simple design. It features two individual parts that join together to lock the end of…
2GT-20 Pulley, 2mm pitch, 6mm belt width. No support is needed, since the top rim has been chamfered. If you printer cannot do the 4mm set screw fine enough, you can just screw it it in against the plastic and it should still work.
Without bearing, should rotate freely on a M5 Screw.
Lets save our K1s :-) This is my linear conversion for X axis. Every version i found was complete makeover. Not this one. This is cost effective coz you reuse most of your stock hardware. Designed for STOCK or POWGE idlers. No software…
Creality K1 belt clamps. Added as much material and strength in this tiny part as possible. Print in HT-PLA-GF or PPA-CF, 0.2 layer height, 3 perimeters, 100% infill. Holes are 2.8mm - slightly undersized so they must be drilled to 3-3.2mm.
Might suggest PETG instead of PLA for these as PLA seems to creep more long term. Zip tie for extra security, if you want Works great on Rook Mk1 and Rook 2020.
I modelled this part using some specs I found online.
Servo pulley replacement for MMX with 4 extra teeth using included servo hub from seleadlab MMX kit.
I needed to clamp a GT2 / 2GT belt for a custom SCARA design, with some tight spots. Most clamps don't run past a sprocket, or tend to slip if they do. I was inspired by Idegraf's design ( https://www.thingiverse.com/thing:1247615 ), but…
Remix of the v3.7 transmission so you can use a longer transmission belt if you can't find or have a 188 belt. This transmission should work with any size between 188 and 202 (maybe even 204) but the shorter the belt you use with this…
For fixing 2GT (GT2) timing belt ends in carriage slits. Use M2 screw or 2mm steel rod, or toothpick, to secure belt. Print with tough material like PACF
BOM Heat insert M3x4x5 4-5pcs M3 Counter sunk screws laying around your floor and…up to 5M length 6mm width belt! Wider ver is under consideration. Update: Added variation for 7mm-10mm belt! Update: Added covers! Update: Added STEP…
For fixing 2GT (GT2) timing belt ends in carriage slits. Use 2x M2 screws and 2x M2 L3 heat inserts. Print with tough material like PACF
For TPU for the papilio lite and similar.
These allow for the addition of M3x4Lx5W heat inserts. Mark the belt with a fine tip Sharpie or ballpoint pen and add/remove teeth as needed. Can be used to clamp the end of two belts to cut to length with exactly identical number of…
I designed this for the Skelestruder. Requires: 2x m3 square nuts 2x m3 headless screws Recommended to print slow and at low layer height. Concentric infill, 3 perimeters. Set extruder steps/mm to 1120 with M92 E1120 then M500 to persist…
Wall mounted holder for Parktool casette tools as FR-5.2, FR-5.2G and FR-5.2GT Printed in Blue PETG, but better to use PLA because PETG is stringing Print Settings Printer Brand: Prusa Printer: I3 MK3S Supports: Doesn't Matter Resolution:…
A diffusor that can be used with the NiteCore MH12GT or any other flashlight that has a head of 25.4mm wide.
Updated model for v3.7 here
Remix Geared Z for 2020, 2gt-200, 80t, 20t, mgn12, nema17, F695-2RS.
I had the bearings fail in the original tensioner for one of my printers. I realized they were only using a single bearing instead of a double and found that there were toothed options which made sense to me. You want the 20T equivalent…
This is 2GT pulley with 60 tooth for 6mm belt, and M8 thread also 13mm nut, its good thing for diy projects:)
When I downloaded this mod, I checked the X tensioner and you will need the original Prusa pulley 623, but If you wanna use Caribou pulley 2gt 16T Toothless, you can check this pulley is “dancing” inside tensioner. I prefer little pulley…
Protect your motion system from bumps and vibrations during transport, hold your bed in place, or just hold tension on that gantry while you assemble! These fit 2GT (2mm pitch) belts (both GT2 and GT3 - yes, it's confusing that these are…
I had a few goes at making a custom tensioner and accidentally arrived at one that matched the original style nicely. This allows the use of a toothed pulley that I think makes for less transmission of belt artifacts into the skin layers.…
A quick remix of the awesome @Psych0h3ad to hold a longer belt. This is for the 6mm version but can make the larger. Uses normal voron style heat set inserts (m3x5x4) and uses the orginal models's center parts you can get here:…
It uses a 2GT synchronous belt as the flexspline, featuring high precision, bidirectional drivability, zero backlash, and zero clearance.Flexspline Output. Filaments： PETG. 2.5mm POM solid beads and 3mm solid beads. 2GT-80 40 tooth 21:1…
Remenica na veterný generátor 12 V (800W) , oska s maticou M18. Červíky M4. Remeň 2GT-6
PETG 245° 0.3mm line / 0.08-0.12mm layers / speed (at your discretion) 5 wall / 4 top-shell / 4 top-shell / 30 infill
Add 0.3mm wider at clamp side
Simple adapter to use 2GT/GT2 as smartphone strap.
Why is the clearance for pins and idlers are soo tight?! Created this print because it was hard to get the pin aligned properly before pressing into place as any slight offset can make it harder to insert into the idler. NOTE: very snug…
Remenica na motorček 12V pre remeň xxx-2GT-6. Červik je 4 mm. Oska má priemer 3mm.
It uses a 2GT synchronous belt as the flexspline,crossed roller bearing, featuring high precision, bidirectional drivability, zero backlash, and zero clearance.Steel Wheel Output. Filaments： PETG. 2.5mm POM solid beads and 3mm solid…
Lets save our K1s :-) This is my linear conversion for X axis. Every version i found was complete makeover. Not this one. This is cost effective coz you reuse most of your stock hardware. Designed for STOCK or POWGE idlers. No software…
